Without a doubt, the best laid out and executed design of any waste oil furnace/forge/smelter on KZbin. The real clincher though has to be the homemade outriggers at all four wheels.
@dalemiller94442 жыл бұрын
Thanks, I did see someone build a similar burner. I couldn’t find screw jacks that would work, so it built my own.
@grassroots9304 Жыл бұрын
Yes, those stabilizers are a nice touch!
@bigalremington2 жыл бұрын
Thanks for this straight forward build. I'll be keeping this design in mind. .....for both applications of heat and foundry!
@Biokemist-o3k Жыл бұрын
Absolutely awesome setup my friend. I have been researching these builds because I am getting ready to do a bunch of castings for parts that are for obsolete engines and equipment. Thank you for the awesome build.
@dalemiller9444 Жыл бұрын
Thanks, you won’t be disappointed with this setup.
@ridwanepribadeeh1997 Жыл бұрын
ALLAAHU AKBAR. SALAM FROM MUSLIM BROTHER IN JAKARTA INDONESIA.
@AnthonyCelata Жыл бұрын
WOW.... Thats a real nice piece of equipment I didnt even hear that lid drag at all. I really want to know how you got that inside lining so perfect. looks like its was some kind of cement mix and you made a mold or something
@dalemiller9444 Жыл бұрын
Thanks, the liner is 3000 degree refractory. It looks and feels like concrete but it can withstand 3000 degrees f. I used a 5 gallon to get the inside form. Works great, I can melt copper, brass and iron with no problem.
@Eisenmann86 Жыл бұрын
Very good idea for fuel burner i like it, 👍👍👍 what is the highest temperature ? can you melt iron ?
@Eisenmann86 Жыл бұрын
check my furnace if you like kzbin.info/www/bejne/mX6VnISpYrysb7M
@philmenzies24772 жыл бұрын
Nice job. Did you make the nozzle as well? It looks a bit like a Nudge burner 🤔
@dalemiller94442 жыл бұрын
No, the nozzle is a Hago Siphon Nozzle SN 609-8 (.75 GPM) with Hago Adapter, SN 609-56. I think I bought them on Amazon. I did make the spin vain.
@ibercombuss.l.quemadoresin56742 жыл бұрын
Hello. I am interested to know if you can manufacture this burner in series?
@charles1759 Жыл бұрын
Where do you get fan on end of nozzle
@dalemiller9444 Жыл бұрын
Made it myself out of a large washer.
@charles1759 Жыл бұрын
@@dalemiller9444 what did you cut it with
@charles1759 Жыл бұрын
I have all the other parts but I have been stumped on how to make this. There is another video on here that shows the something like it but doesn't say where he got it. Maybe you could make a video on that
@kirkwerner18999 ай бұрын
did you make the fan/mixer ?
@73superglide622 жыл бұрын
Do you have part on part on the end that gas and oil sprays out of
@NoOneButRonPaul Жыл бұрын
What's the long red hose/pipe connected to? Compressed air?
@dalemiller9444 Жыл бұрын
Yes, it’s connected to my air compressor located in my shop.
@NoOneButRonPaul Жыл бұрын
@@dalemiller9444 thank you.
@MaliksGarden3 жыл бұрын
can we use this in a kiln
@dukedez15 жыл бұрын
That’s a lot of galvanized pipe Be careful with the fumes from that burner.
@dalemiller94445 жыл бұрын
Yes, galvanize fumes are hazard. The way this Burner is set up, only the tip get hot. All the heat is inside the foundry. Thanks for your concern.
@nnnnnnnnnick55573 жыл бұрын
With how hot thta thing is it'd burn off all that galvinized crud real fast