SMD Soldering - QFN Package

[@chloemcholoe3280]

Soldering has never been so emotional

[@Thesnowiswhite]

Emotions harm business. Emotions are not bad, but very dangerous.

[@MrFrezeeTr]

Tears dropping from my eyes while watching it :'(

[@yanyanyan25]

And soothing, calming and relaxing.

[@electronicscaos]

Everyone must agree that it is way better than that annoying beats in viral diy videos.

[@vrushabhmaral7759]

If you really loves work , then Brain will release good dopamine 😊 good presentation 🎉

[@popiyag]

This method looks very easy. But practically it is not. Usually we happen to do this kind of work as a rework. There are many parts already installed nearby. Here there are no other parts, no pads connected to ground. The thermal pad of the chip was ignored. And the board appears to be a double sided (two copper layers) only. When it comes to a board of eight ten layers with heavy density of copper and several pads connects to ground , picture is completely different. We have to use a hot plate to preheat, under the cradle, which holds the board and place everything under the microscope. Then we have to perform the soldering as in the video, sometimes with the help of hot air gun. Everything should be done very carefully, taking care not to burn any connector or part because under the microscope we can see very limited area only. When we perform our duty very carefully, the worst thing is our employer used to bring his laptop to show us these type of videos and points us " See , how quickly the youtubers do this."!!!!!!!!!!!

[@vasiavasin5180]

вот и хуй-то!!!а автору похуй на это!......и это,я бы слал на хуй таких клиентов!!!

[@NicolaiSyvertsen]

For hobbyist projects you make sure to make PCB designs that make manual assembly easier. You don't use the smallest pitch ICs or 0603 passives etc. And chips like these are often soldered with solder paste and hot air.

[@ManishKumarIITG]

Next time your employer says so, ask him to hire the youtuber.

[@aaliyahagwan]

@@NicolaiSyvertsen Yes

[@aaliyahagwan]

@@ManishKumarIITG 😂😂😂

[@Virtu0city]

Two o'clock, middle of the night and I’m watching some random dude soldering... Good night

[@siriokds]

The same, at 3am. Two years later in the middle of pandemia.

[@zoraamethyst2147]

3 am and us

[@DavidockAI]

Same but in 2021

[@freemasonry666]

3:25 am

[@homelessguy3266]

Same as me, mate... 5 o'clock in the morning 😅

[@alexm7056]

This method only works well for a footprint designed for "handsoldering" with iron. That is why pads on breakout board are long enough so it is easier to get heat transfer with regular soldering iron tip.

[@hansfritz7827]

Dont forget the power pad under the part, you need hot air to mangage to that :)

[@klazzera]

it can also be achieved with soldering iron from below since there is thermal connection

[@JoseGustavoAbreuMurta]

I managed to weld a 0.5mm QFN 28. I learned with you. Perfect! Thank you very much!

[@richardsilva-spokane3436]

Excellent macro photography and editing. Perfect soldering technique 👍👍👍👍👍

[@The.Ordinary.People]

I think there is a big issue, no solder on the ground/central pad if it's necessary.

[@shost58]

not good, need thermo fan for soldering central thermopad chip

[@thomas_2412]

Damn... the music makes it soooo refreshing

[@weinickchan]

i like your confidence anchoring the second spot without checking if there is any misalignment..

[@MeepMu]

I've never seen something so beautiful in my life!

[@serviciotecnicotab3115]

MUY BUENOS TUS VIDEOS GENIO NOS INSPIRA A TODOS LOS QUE HACEMOS ESTO SALUDOS DESDE ARGENTINA

[@johnsim3722]

The advantage you have here is the large pads to allow you to use a relatively large tip when soldering. It's sucking the solder up from the joint. Problem is that when you follow the manufacture's footprint guide you get minimal area. In production thankfully I'm using a stencil and a convection oven. But sometimes I do need to rework these devices and what I do isn't too dissimilar to this video. Using a large chisel tip iron, lots of flux (liquid rather than paste) and make a big blob of solder to be dragged along the side of the IC. Replacing these ICs you need hot air. What I've also found is that with ICs that have a large thermal pad you also need to add a heater underneath the board. Set it to 100 / 150C so that your hot air has less work to do. You'll do less damage, or none at all, this way! Replacing just carefully put down some solder paste, you don't need much, and then again back to the hot air. But they really are an absolute pain these packages!

[@omarquispe4556]

I u u

[@cris101879]

77ii

[@user-rs8zg8ey2b]

QFN are a breese, csp even easier, what is tough is the new 56 Gbaud packages.

[@hugepines3990]

@@user-rs8zg8ey2b BGA1156 ;P

[@user-rs8zg8ey2b]

@@hugepines3990 We now have 60x60mm 3488 pad packages (80amps), these need everything correct to get them working. I still believe the 56 Gbaud are the hardest, everything needs to be perfect.

[@matthewpeterson5159]

watching this makes me ask myself why I waited so long to get into SMD (as a hobbyist)

[@tonyennis1787]

Be prepared to practice for a long time.

[@ДмитрийДубравкин]

А пузо-то не припаял? Надо-бы сначала феном...

[@vas9l.matb.vashu888]

У него просто для показа, так задевает, а тебе конечно, феном надо будет угреть

[@vas9l.matb.vashu888]

Дыру видел в плате под микорсхмой? Второе, у него была цель пузо паять? Или ноги тока?

[@Евгений-ж2и3у]

Вот вот, а у пуза как обычно земля и микруха не заработает, или вообще в аут уйдет!

[@aleksandrmatlachov3934]

Перегреется и сдохнет, так нам и надо.

[@Thesnowiswhite]

Платон Карпов, цель была убить микросхему? "Пузо" к плате паять надо обязательно. И потом каждый слесарь знает где бывают дырки. Отверстие это не мешает никак. Феном не феном, а залудить выводы микросхемы перед пайкой обязательно надо (Есть исключения. Но не в данном конкретном случае.). )

[@martinwashington3152]

Thanks for making this video, I'm getting in to SMD/SMT boards myself and this video was very well presented and explained :) I'll subscribe :D

[@briandelgado3726]

Tut tut 6⁵⁵33 a eoyeruyuey3y3ygggegertgrte tree teddy toy tree

[@samuelgonzalez317]

Dude, you make this look like art

[@janbalga7702]

Very nice work. Great close-up.

[@Pixell_Eletronica]

Perfeito! Eh gratificante e relaxante ver um trabalho assim bem feito

[@oskimac]

the saddest qfn soldering video... :-(

[@MarioMartinez-vl4wf]

when said "unfortunately solder mask damaged..." plus the music, I almost cried

[@berembah]

They use the video plot in latest movie, really sad. The move title I think "You beautiful feet shower my lip"

[@gavincurtis]

I see this particular package type causing a lot of cold solder failures in equipment we repair. Seems that the TQFP packages are better as their actual leads are more capable of dealing with thermal expansion?

[@TheOriginalSycHolic]

if you didnt notice the best joints he did was the 2nd row when he did only a few at a time and started away from it and slid in lightly touching the side of the chip with the tip only... 2:45 But here is a question the small brown pads in the corners is that for automated grip points or they maybe ground or heatsink contact points or something? also long as the trace isnt damaged you can always paint over trace cover with a matching clearcoat and use alcohol to blend the edges.

[@KallePihlajasaari]

The brown bits are exposed parts of the leadframe that have been cut flush, they help to keep the leads and the IC from moving while they encapsulate the part. The leads are cut and trimmed and the rest of the leadframe is removed at the same time.

[@mikaelkalki3171]

This is such a beautiful video

[@sergeydanilin5204]

Если так на печатке запаять - не сложно. Плюс брюхо не пропаяно. Я паяю так: аккуратно залуживаю посадочное место и чип. На чипе должны получиться бугорки на выводах. Совмещаю чип и посадочное место. Грею феном до момента посадки. Проверяю микроскопом правильность посадки.

[@e.w.2396]

Simply the best !!! 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻

Very professional, excelent work

[@ВладимирК-ф8ф9д]

У этой микросхемы должно ещё припаиваться пузо, поэтому - термофен. Нужно облудить все контакты до пайки. То, что ты показал - конечный этап для контроля посадки микросхемы.

[@HOLLYWOODlosANGELES]

*C'est bien présenté, j'ai compris maintenant comment souder ce type de composants. Merci*

[@j.lietka9406]

Still came out clean and perfect!

[@nheng6913]

Nice video, love the wave effect. It's so easy on boards without ground planes and on leaded solder though. And no thermal pad. Can be a living hell without preheater on bottom and proper temperatures/times.

[@elbakkali]

Thanks for making this video super my friend

[@puaktopblm]

А подложку припаять?

[@killerpigszombi3382]

Если микруха не нагревается то не нужно

[@ТолянКурасава]

Подложку потом на саморезы там есть дырочки

[@killerpigszombi3382]

NEY Industries, ну это логично, но по факту я так понимаю это делалось что бы сделать видео перфекциониста. Так же можно снизу прогреть и подложка прихватится

[@3JIbIDEHbv2]

у Россмана гораздо лучше видео по пайке "qfn + Rossman" kzbin.info/www/bejne/o6OUhomGqKqrn6c

[@alexkross125]

С обратной стороны олова лупануть через отверстия

[@bjl1000]

for the central ground pad , I would put solder in the hole , from the bottom and heat the pad through the hole with my soldering iron.

[@clkunde]

I preffer to use hot air to sold QFN's packages, specially because the central pad!!!

[@branieffpulido]

If there was a reaction of I love it on youtube I would put it ... that work so neat and perfect I loved it

[@themadatheist1976]

Nice debating if I should get cheap hot air gun or just use my soldering iron to add the 2nd m.2 connector and the capacitors for my laptop MSI decided to leave off.

[@mhwong1865]

You forgot to solder the thermopad/GND Pad that located underneath the chip ,which may be very important for the performance of chip align with the specification.. when soldering QFN with thermopad . hot air soldering and drag soldering method shall be applied

[@agustinflorespatolin7333]

Excelente pero una duda la parte de en medio no es necesario soldarla?

[@AThreeDogNight]

You make this look really easy although I know that it is not, especially with a soldering iron. You must have done this for quite a while now.

[@UCanDo]

Какой микроскоп вы используете?

[@marciosouza5864]

Muito bom seu trabalho, deixo aqui saudação do Brasil.

[@sophon1999]

มาเป็น Fc sub ใหม่ครับ

[@chino123224]

What type of microscope you use??? And thanks for the videos saludos desde mexico

[@michaelschecker2716]

I solder QFN with hot air in 1/100 of the time. The best moment is when the QFN allign itself.

[@Peter.Jensen]

Please show 🧐

[@DatagorElectronics]

Hmmm. And what about a big central thermal pad? It can't be done without a fan, isn't it?

[@MrMubeenyou]

MrDatagor i think there should be heat sink paste under IC chip

[@Androkavo]

Some vias holes in thermal pad allow you solder on top or bottom layer by soldering iron

[@DatagorElectronics]

Agree!

[@DanielKolar-qo4ci]

And some ICs have on this pad GND power pad. We are using hot air gun for these chips

[@Bavlogic]

Androkavo and what if no holes on the other side??? And it's 90% of the time

[@ok-eh7zm]

you make it look so easy

[@ТимТимыч-э9х]

Просмотрев видео вспомнил ролик где чувак говорил это просто охуеный зум 🤣

[@kynkai]

this is so satisfying

[@revenger9900]

True😋

[@bidz1947]

Concur. Most therapeutic... N relaxing I find when replacing large SMD ICs.

[@WhatAWondWorld]

Красиво! Спасибо!

[@beteadaniel2240]

Soldering only the terminals of component without the soldering the thermal pad can lead to malfunction due to overheating. For this type of component air heat soldering method is better to be used.

[@adamw.8579]

Exactly, preheater and hot air, basic tools for SMD repair. Others methods are patchworking and not reliable.

[@StoesA]

Funny, taking a QFN package and soldering it to an extension board... Good soldering though!

[@karmachameleon600]

Sometimes it is required when you need to test the circuit on breadboard.

[@KaiDon1]

I enjoy listening to the backgrond music.... very relax.

[@Majidmohamod]

Me too, you can find it here kzbin.info/www/bejne/pniqnquchp6ieNE

[@burntable]

2:34 thanks for keeping it real!

[@fadifadi-4u]

Beautifull work!!!

[@MartinWar]

1:12 Why we need flux on the two corners ? (or it is soldering paste?) What kind of flux can be cleaned by alcohol?

[@robin_dong]

Use flux to fix the QFN-chip looks like a good idea. I will try this method later.

[@elcomentador2408]

Nice video, like the music.

[@MovilOne]

Good! 👍

[@謝坤宏-r8z]

you don't need any soldering for central Ground pad? oh, there are some people mentioned.

[@rechtsgelijkheidvooriedere9419]

Huw abouut the heatsnik pad at zee underzide ¿

[@AsthmaQueen]

actually makes me think doing a QFN might be easier since the tabs are so small and less likely to bridge than TQFP.

[@mattlanderclairzil7316]

Goog work bro..

[@tamyboy1]

It is a totally different ball game when those leads are not this long. Which is 99.9 percent of the time. But thanks for the video

[@user-rs8zg8ey2b]

And with high speed signals (these are not), you cannot solder to the leadframe (side of package), well you can, but it reduces high speed preformance.

[@MadJDMTurboBoost]

@@user-rs8zg8ey2b Why is that? I was under the impression those were just test points and if solder sticks to them theres no issue. I'm curious why that would impact high speed performance?

[@user-rs8zg8ey2b]

@@MadJDMTurboBoost My company is doing the bleeding edge of tech, high speed data, each year we reduce the sice of the ac coupling caps, 0402, 0201, 0105, etc, each disturbance of the high speed signal has a reflection, the smaller the component the less reflection. The pads on the part keeps getting smaller, so now you cant solder to the leadframe like I did 5+ years ago, it just screws with the signal (in a bad way).

[@mineown1861]

Where did you get that metal siphon you had on top of the alcohol bottle ?

[@mohamadaldarwish6678]

Professional 😍👍

[@r3montickplay951]

Great Job !!! Thanks for the cognitive Video =)

[@nikolaykalinin3395]

Прекрасная пайка,очень аккуратно и с умом!

[@RahulElectronicspoint]

Nice video sir

[@zubershaikh5546]

Very nice which tools you use plz tell me I'm waiting for you sir

[@TheAerotrike]

Перед установкой лудится и плата и корпус мс потом феном припаять. схема сама центруется. Излишки припоя при нажатии выходят в виде шаров.

[@killer199786]

Всем русскоязычным 1) он не припаял массу микросхемы, которая одновременно выступает теплоотводящим элементом 2) паечные мосты снимаются только чистым жалом при нанесении флюса каждый раз 3) он за каким то чёртом снял старый припой, и сам же написал что нужно быть осторожным, для тех кто не в теме объясню, если много тыкать паяльником в такие посадочные места, то контакт просто перегреется и оторвётся от текстолита А вот вам инструкция как надо делать 1) Аккуратно лудим площадки с флюсом, в т.ч. и массу(пузо) на печатной плате 2) включаем фен на 270 градусов и усаживает микросхему на свое место 3)еле еле толкаем микруху под феном, если микросхема вернётся на свое место, то убираем фен, она на своем месте 4) если есть не пропаянные ножки, аккуратненько с флюсом тонким жалом пропаиваем каждую отдельно а не все подряд Профит, микросхема установлена

[@TheBypasser]

Neat, but not a QFN soldering you expect :) The "real" one is not much harder though, the main difference is you also have to tin the package terminals to get the same pillow shape as you got on the PCB pads. And better use a blowtorch with a catalytic nozzle as advised in some (can't recall which one exactly) repair note instead of hot air gun, makes things way easier as nothing gets blown off.

[@tforgo]

Great footage quality. I would aprecheate voice over music. Explaining stuff, pros and cons. Etc.

[@hightttech]

Nice camerawork.

[@DSD-u2m]

What is the temperature when you solder this IC?🙏🙏🙏

[@ilangokrishnan5956]

You didn't soldering center thermal pad and using more flex on rework.it is very easy work .

[@customthings3081]

And what about the power pad? how did you make the soldering?

[@АндрейБондаренко-г1ы8ы]

Отличная работа👍

[@thecoba42]

Hey all, I've been trying to find some flux cleaner like OP used in his video. The dispenser looks pretty practical, can someone point me to where I could find that kind of bottle ? Thanks !

[@gateitogototo8976]

it's pretty important to use the thermal pad too

[@IsaacOLEG]

very nice, but some have a middle leae part, joined with one of the pins, I suppose then one cannot avoid hot air is not it ?

[@SoorajGopakumar]

That was nicely done!! What magnifier do you use?

[@pierdolio]

Why is your image so clear compared to others, I've seen, doing the same thing with a microscope?

[@melissayang7067]

hi Adam, we are selling microscope, you can see them in my channel.

[@Ivan....Ivanov]

Лютый флюс... Даже маску жрет )

[@MrPepe2162]

How's underneath on that one how you engage good connection if there's no re-heat under components.

[@huczula3534]

In which temperature you soldering?

[@mdkashemali3451]

You can also use Hand sanitizer instead of the alcoholic flux remover, because hand sanitizers also has alcohol mixup more than 70%...

[@jasonmorgan661]

Theres that damb toothpic and same can of flux....😌 love it lol.😃

[@buckler19]

Can you recommend a comprehensive tutorial about the basics of IC technology? (PCB fabrication, main surface amount elements and their function, main applications)

[@mhwong1865]

Use Solder paste method with drag soldering is most suitable for QFN chip that have thermal pad

[@kobtcom]

the ground under chip is not solder. so effect to chip high temp. and unstable work

[@tarekfiliachi6350]

NICE SOLDERING AND VIDEO.

[@PiotrK2022]

@Androkavo LOL, center pad should also be soldered, because in that case solder acts as thermal-paste and center pad acts as heatsink... Without it chip may overheat na fail again.

[@masprassaja3818]

So satisfying, next buy flux. :)

[@chinthakasandamal8283]

Super smooth

[@htd7814]

Hello ! What kind of camera do you use to record videos? Verry clear image. Thank you

[@rcarioca]

Questionable soldering by relying on contact with bare copper side pins

[@UedersonThec]

Very good! Trabalho muito bom!

[@MaquinasAbiertas]

You missed the power dissipation pad.