iMachining 3D - Brillen Modell fräsen - 16MnCr5

[@Slovnoslon]

Представьте весь опыт фрезеровщика на универсальном станке, который только может быть. Точное понимание величины съёма материала от вылета инструмента и многое другое. Всё это оптимизировано и очень просто в использовании. Аймашининг работает просто идеально.

[@harryt622]

None of these videos finish the part. If you're not going to finish it during the video at least show the finished product at the end.

[@TheWireEDM]

The finsihed part was shown in the beginning of the video, as is customary to show first what the end result will be and people can then just skip the whole video if they are not interested.

[@Penguin_of_Death]

Yeah...try paying attention to the beginning harryt622

[@stexxvan]

but he just doesnt show the most interesting section of the manufaturing where the Solidedge actually makes sense...... what he shows for this enough a simple notepad. 2d milling

[@JaakkoF]

@@stexxvan They show here exactly what makes companies money: getting material removed as fast as possible with the least amount of tool wear and programmer fatigue. Finishing is always the same, you can't skip anything in it.

[@cnctobi]

Die Schnittgeschwindigkeit kann man aus den Angaben ausrechnen, Vc für beide Fräser ist 436 m/min.

[@dunichtich100]

16MnCr5 is the steel with the highest kc1.1 not only the cam here is good, but the mill has to be incredibly strong and still to mill at such speeds! :0

[@JaakkoF]

In SolidCAM there is a slider from 1 to 8 I think, that you can select the aggressiveness of the cut based upon your material holding, type of operation and machine rigidity. I used a clapped out Primero with a top speed of 8000 RPM and 6000 mm/min feeds and it purrred happily with the setting 5 with a part held in a vise.

[@RD-ij2sz]

Cutting through alloy steel life a knife through butter . Excellent ..👍

[@jlw1911]

As a Mastercam user... that tool path is just sexy. I wonder if this path works like mc. Do you set a step up? What Is tool diameter? SFM? WOC? IPT?

[@TheWireEDM]

Nope, it works completely different to MasterCAM. In MasterCAM you have to figure out all the options and hope it works. In SolidCAM, you tell it the tool length, tool diameter, tool material, helix angle (not necessary but helps in vibration cals), workpiece material and/or hardness and the solid model you want to machine, the initial workpiece block, select machining aggressivenes with a slider from 1-8 and hit go with your feed & speed pots at 100 % and go have a coffee. MasterCAM is childrens playground stuff compared to this.

[@chribo_h2941]

künstler sind das die sich sowas ausdenken ^^

[@tomthompson7400]

looks like sci fi ,,, amazing , like to see finished part though

[@elias38]

It's at the beginning of this video.

[@baovu14]

what endmill and what fixturing is that? looks like flame-cut matl

[@TheWireEDM]

The material looks more like standard bar stuff, not flame cut at all.

[@OriginalJetForMe]

What machine is that?

[@SolidCAMgermany]

+Rick This part was milled on a Hermle C30

[@rickmann258]

+SolidCAM Deutschland I wish my Tormach could do that :-)

[@SolidCAMgermany]

:-)

[@sunside79334]

+SolidCAM Deutschland what else than a hermle. ;) watching the video i was already impressed about the stability and smoothness of the milling process despite the heavy workload on the end mills. those hermle machines are just ridiculous when it comes to precision combined with power and speed, and worth every single cent of their price. great vid as well, it's like TPC porn.

[@TheWireEDM]

Your Tormach can do that, just use slightly less aggressive slider setting in SolidCAM. Heck, you can even mill stainless on a crappy wood router with this software.

[@wawanmuldiantoro7159]

Wow.. what's the speed of the spindles?

[@steveprice766]

It tells you at the start

[@شكاكي99-ص4ح]

نوو

[@ДмитрийЛесоруб]

Увидел.😁👍 Против ЧПУ не спорю.😄😄😄 Только ручная фрезеровка-ближе к сердцу...😉😉😉 Хороших дней... Хороших дел...😁😁😁👍👍👍🤝🤝🤝

[@ronnyh411]

also da es sich beim 10er Schaftfräser eindeutig um einen vier schneidigen handelt, beträgt fz 0,1154mm/U geht man auch beim 16er Fräser von z=4 aus, so ergibt sich logischerweise ein fz von 0,174mm/U wirklich sehr beeindruckend!!!

[@Dan81825]

Genau, fz und mm/U oder sowas :D Kannst mir des kurz erklären? Ich interessier mich echt dafür :)

[@ronnyh411]

Dan81369 was soll ich dir genau erklären? dich etwa mit allerlei formeln zubomben? xD

[@StarWarsUnited123]

fz = Vorschub pro Zahn....umso mehr "Zähne" also Schneiden der Fräser hat desto schneller kann man logischerweise den Vorschub wählen. mm/U = Millimeter pro Umdrehung....das ist einfach die Angabe des Vorschubs

[@Dan81825]

StarWarsUnited123 ronnyh411 Passt so, danke euch :)

[@88690]

ronnyh411 Da ihr ja anscheinend vom Fach seids, hier mal die Frage warum hier überhaupt null gekühlt/ geschmiert wird? Sehe da maximal so eine Druckluft Zuführung, hätte aber erwartet das bei derartigen Vorschüben und Geschwindigkeiten eine Flut von Emulsion eingesetzt würde. Der Maschinentisch ist ja nur am rumwackeln!

[@petercarr5105]

What end mill are you using ?

[@Gurpreet6672]

1/2 inch varimill.....

[@21qq21qq]

viel Spaß beim abdeckeln

[@millakilla]

2:25 get sum!

[@taystew]

2:56 lol i just imagine the guy that wrote the program was coked out of his mind that day.

[@Cerebralcinema]

+Taylor Stewart (Picwick) Solid Cam writes the program. If you're referring to the brief pause, the same thing happens on the opposite side @ 2:29. It's because the spindle changes speed. Machines typically aren't programmed to change spindle speed in mid feed. Although it's possible to do it, it's generally not recommended.

[@515sheriff]

+Taylor Stewart (Picwick) I seroiusly doubt it. And, yes Solid Cam does write the actual program.

[@TheLuRage]

ae/ap?

[@ilanv2693]

איזה מכונה מבצעת את העבודה ?

[@ubbgn]

I want to see that tool! : )

[@Chalera4x4]

Demonhera do caralho 👏 parabéns

[@michelrosier468]

Looks like waveform milling I use with Edgecam. Either way.. Porn! Love it.

[@steveprice766]

I prefer pornhub. 😁

[@juliocesartenorioolivera5118]

Hi porn europe😅😅😅😅

[@mohammedarkia8986]

Very nice

[@andrerothweiler9191]

Mein Chef würde mich sicher dazu zwingen alles ohne Cam zu programieren :( so lernst's besser Juuuunge

[@arezkihassaine7450]

je voudrai bien acquérir un matériel de tournage numérique pour fabrication de différents moules. j'attends vos offres et orientations.

[@hieungoquang4312]

Sài phần mềm gì đó ad ơi

[@wippy748s]

impressed big time !!

[@majid.mughal1430]

I need a job i am programer

[@ichbin4040]

BÄM BÄM BÄM! Ausserirdisch!

[@Ima184mm]

German Steel!

[@leegordon5834]

When I try this type of machining I just break tools.

[@bobbanaszak9356]

Are you using shrink fit tooling?

[@leegordon5834]

No

[@Gurpreet6672]

try 1/2 inch carbide 4 flute varimill with stepover of 7% of diameter of tool...speed and feed depends upon the material you are using...

[@TheWireEDM]

***** Basically the only way to get a tool path like that is to use SolidCAMs iMachining. It knows how to calculate chip loads, unlike MasterCAM and others.

[@YorenM]

true, i never used it but i hear many good things about it!

[@majid.mughal1430]

4 year experience

[@nitroglicirin]

a lot of empty of passages without work.

[@GyrosGeier]

Conventional vs Climb milling, see en.wikipedia.org/wiki/Milling_cutter#Conventional_milling_versus_climb_milling

[@depenthene]

+Simon Richter I don't agree with Leoni 48, but his comment has nothing to do with conventional or climb milling. I think he means there is a lot of movement without tool engagement.

[@GyrosGeier]

Yes, that's a direct result of only using the tool in one direction.

[@TheWireEDM]

..and it still beats all the competitors in CAM.

[@qinjeremy]

bravo

[@TheLuRage]

Vc? fz? ae/ap?

[@TheWireEDM]

All variables in SolidCAMs output. Vc depends mostly on material, tool material and aggresiveness of the cut, but with SolidCAM you just select what material, how aggressive you want to cut and that's it, it figures out all those variables for you and changes them on the fly.

[@enriqueguzman71]

CHINGON

[@generalwalter8201]

EIn Kleiner Tipp ( KSS ) Kühlschmierstoff :D

[@cedi98]

dir auch einen kleinen tipp :) wenn man keine ahnung hat sollte man lieber nichts sagen ;)

[@phammr9869]

vãi thật

[@toast47624]

WOW! That was ridicules to watch.

[@islamjaber2544]

mohammad

[@arezkihassaine7450]

je voudrai bien acquérir un matériel de tournage numérique pour fabrication de différents moules. j'attends vos offres et orientations.