This helped me alot I thought my car hood was cooked but now i realize i can just go up in sanding grits then I'll finish with a buff to remove the haze
@highbeamed8 күн бұрын
LMFAO same
@tikman31715 күн бұрын
🤣😂🤣😂🤣😂then your clear coat will keep getting thinner & thinner. Use polish compound is good enough for newer model car 🚗
@givemeabreak87842 күн бұрын
Sand and sand and sand and oops there's no paint 😂😂😂. Yep just buy our sanding pads 👍. DON'T blame the ad !!
Жыл бұрын
Very nice video, but a side-by-side comparison would have been awesome, with one side of the panel sanded and polished, while the other one left as is at the beginning.
@ogkev19248 ай бұрын
You didn’t see the difference? The end result looked way better
@Topcoatdetail Жыл бұрын
Kovax are dry sanding discs. Water is not required
@jacobshank93628 ай бұрын
I agree; furthermore, it is actually advised not to use any lubricant from Kovax, because it will cause more clogging issues--these dry discs already have a substance on it designed for dry-sanding efficiency.
@Gone_Rogue3007 ай бұрын
Mines have many cracks in her. Ive veen sanding it down to the weave to remove the cracks
@bmci007 Жыл бұрын
What sealant would you recommend on a budget?
@BeaterCollector10 ай бұрын
A wet on wet sealant, there all the same. Spray the sealant, let it flash then paint over it. Done like a da done done.
@gzus14827 ай бұрын
@@BeaterCollectorWait, you're talking about sealer not sealant right?
@GoogleUser-yj1wy5 ай бұрын
TurtleWax
@thisisyourcaptainspeaking22595 күн бұрын
@@BeaterCollectorPaint over what?
@Lolatyou33214 сағат бұрын
What's the point of doing 1500 grit -> 3000 grit? A fresh clear probably doesn't even need that and if it does it's probably going to hit into the paint..
@sthildas4857 Жыл бұрын
Good advice, I detail paint CSM says this will only take off 1/10th of the total clear. Orange peel paint is the bumps. Do every step, thx for this great advice. Use a DA.
@sthildas4857 Жыл бұрын
Jason Rose wet sanded a paint section, then measures each layer with his Positector. From base to clear... 1.7 base 1.8 paint 9.0 clear 12.5 Total
@Rabbit.7607 ай бұрын
Dude I swear to God the clear coat looked better before u started
@MisterManiac456 ай бұрын
No if you rewind it you can notice it looks a tiny little bit better after but imo this is too much work just to make it barely even noticeably better
@natescustombuilds3 ай бұрын
You can literally see air bubbles or lint at the start of the video, the polish made it way better.
@Rabbit.7603 ай бұрын
@@natescustombuildsI can't see any of that... I see a deep and clear reflection at the beginning and at the end I see body shop tracks
@Rabbit.7603 ай бұрын
@@natescustombuildsI believe what you're seeing is the heavy metallic in the paint
@natescustombuilds3 ай бұрын
@@Rabbit.760 it’s lint or air bubbles, trust me my friend I know what I’m talking about, look at my videos that I uploaded for proof I’m not just talking out of my butt, I know how to paint and have enough experience to know that’s air bubbles or lint. A polish will always 100% everytime make your paint job look better.
@user-cv5oq1jt4j2 ай бұрын
looks great , what would you recommend on using as a sealer thanks ?
@ghostwarhammer0077 күн бұрын
So clear coat then sealer? Whats sealer?
@robertcarlos787 ай бұрын
When you wet sanding what speed you put on?
@simsneon210 ай бұрын
No, check your paint thickness first
@SARKAZYMYT7 ай бұрын
Not necessary at all lol
@akmalhaqim4679Ай бұрын
Please anyone let me know what speed on DA polisher for the sanding & is there any hand pressure applied when sanding or just guide the DA throughout the surface??
@krystallyn83513 ай бұрын
Can You Do This Same Process For Dirty Paint, Dust/Dirt?? Right Now We Are Cleaning Up A CandyApple Paint Job !
@Gamer_Marcy_God3 ай бұрын
Can I use a DA machine I use for normal paint correction to do this type of sanding Dave?
@customspraymods3 ай бұрын
Ideally a smaller orbit is best 2.5mm. But the 21mm or 15mm seem to work so why not hey.
@minchia04 Жыл бұрын
How many coats of clear coat do you need to prevent sanding through the clear and into the paint?
@customspraymods Жыл бұрын
2 coats of clear is about 80 to 100 micron thick. This takes off no more than 10. It’s only really levelling the high spots.
@Praise___YaH Жыл бұрын
Guys, Salvation is so Simple HalleluYAH translates “Praise ye YaH” YaH is The Heavenly Father YaH arrives via the TENT OF MEETING YaH was Who they Crucified for our sins - Ancient Semitic Cuneiform of Moshe (Moses) - Isa Scroll (The Original Isaiah) Isaiah 42:8 "I am YaH; that is my Name! I will not yield my glory to another or my praise to idols. Isaiah 43:11 I, I am YAH, and there is no other Savior but Me. Isaiah 45:5 I am YaH, and there is none else.
@DiscreetspdАй бұрын
Nice and easy way but not for the uninitiated 🥺
@martinhoogenraad45279 ай бұрын
How often van you do this, before you ruin your clearcoat.
@turk0108 ай бұрын
Depends on how much clearcoat you have.
@dompesky1693 ай бұрын
Can you do this without the compound and polish?
@customspraymods3 ай бұрын
No
@user-jv1oo9cr7d6 ай бұрын
Sending machine not use??
@BeaterCollector10 ай бұрын
It doesn't work. You must have 7 coats of clear to help prevent breaking through. Just do 3 coats and do the sanding by hand with a fine grit 2000, it always comes out perfect.
@31acruz5 ай бұрын
Can I use my regular polishing DA to wet sand? why use a sander ?
@customspraymods5 ай бұрын
Normally a sander has a smaller orbit to a DA. The smaller orbit makes smaller scratches which are easier to polish out. You can use a DA but keep that in mind. 👍
@daviddeavila90196 ай бұрын
What kind of machine was that to sand
@TennisDK-hy7hr Жыл бұрын
Is it safe to wet sand with a DA polish machine? I have only wet sand by hand and its hard
@sthildas4857 Жыл бұрын
At this level of cut 1.5 2k 3k..each layer improves the other. Good compounds with bring back 3k use a da.
@kevinohagan963 Жыл бұрын
No do not do this, especially with a d-a. Use your hand 👍
@daddychill8070 Жыл бұрын
@@kevinohagan963how come?
@kevinohagan963 Жыл бұрын
@@daddychill8070 many reasons but the main ones being it will cause pig tails and unevenness of the clear coat. This is what you want to avoid, when you use your hand you wont get this, plus you actually feel what you are doing!
@matiusteddyc.856 Жыл бұрын
why wet / Damp Sanding when it's fresh?
@Lalo-qj5ek4 ай бұрын
Will strip off the clear if you don’t wet it when it’s fresh
@PierreDuToit-to7mbАй бұрын
No sealant on fresh clear. Wait a the very least a month.
@techlabs93852 ай бұрын
What sealant?
@NycForgiato2 ай бұрын
ready for a sealer? what sealer?
@customspraymods2 ай бұрын
A paint sealer like ceramic coating or wax.
@nastysoda92123 ай бұрын
starting at 1500 grit way too much, gonna have scratches and swirls
@customspraymods3 ай бұрын
Nope.
@user-jv1oo9cr7d6 ай бұрын
W you use da sander machine no problem?
@AbdulSamad-mw4re10 ай бұрын
How many passes do you have to make when wet or dry sanding
@Dub-ry4cs7 ай бұрын
You’re trying to eliminate swirls and scratches which you can see when sanding. You only want to sand just enough to remove those. Don’t want to do too much that you eat through too much clear coat.
@jacobDDonyoutube11 ай бұрын
can I do this with my orbital sanderDA/polisher I have crows feet and too be safe should I start with 2k instead of 1.5
@j.waylonmusic6424 ай бұрын
Do not mess with the paint at all if it has crows feet. You will regret it.
@jacobDDonyoutube4 ай бұрын
@@j.waylonmusic642 I did it I regretted it but I did hand applied clear coat hopefully itll preserve
@huh_what_jdm808911 ай бұрын
Will this help with a little yellowing in clear coat
@_Stupid_Idiot11 ай бұрын
No
@danbanks7930 Жыл бұрын
Also you can start by not getting your car painted at Mako they are trash😅😅😅
@zackeryjames-ej2iz11 ай бұрын
I like to see you do better.
@ClutchCobraKID110 ай бұрын
😊
@GaryThatsgary2 ай бұрын
What's new ?
@customspraymods2 ай бұрын
Wait. That's not the best comment ever. Why not?
@GaryThatsgary2 ай бұрын
@@customspraymods I wasn't trying hard enough?
@scootalong425421 күн бұрын
“Nice and easy” uh hu
@MustangFourSix Жыл бұрын
Do you have an email so I can send you pics of my car to get advice on how to fix clearcoat and also what is sealant
@darrylburge3620 Жыл бұрын
3000 is over the top Finnish with 2000 then lambs wool then sponge pad lambs wool will get the 2000 scratches out
@JAGMotorworks3 ай бұрын
Sealer? Like what
@ashketchum18273 ай бұрын
A wax, polish or coating.
@aps552411 ай бұрын
Hi can you spray my 40 year old car
@BeaterCollector Жыл бұрын
I tried EXACTLY the way he did it, it didn't work.
@customspraymods Жыл бұрын
Can’t learn in 60 seconds sorry
@keithpeterson3805 Жыл бұрын
Lol might aswell just fuckin sand it back and repaint it bro
@customspraymods Жыл бұрын
@@keithpeterson3805 and get more dust.
@cesarbrizuela578711 ай бұрын
@@customspraymods😂
@AmazingYT10 ай бұрын
What happened?
@chiefwraps7711 Жыл бұрын
No, it is NOT "fixed." You have removed some of the clear coat that is a protective layer to the base coat paint. Now the smallest rocks or debris will scratch and chip all the way through the clearcoat and base coat. You should have resprayed the clearcoat in order to maintain the same level of protection as the factory when the vehicle was manufactured.
@sthildas4857 Жыл бұрын
We detail cars like this all the time we measure the depth of paint...you may not do this on very thin paint...just use a da with Meguiars 105/205
@baldy1209 Жыл бұрын
Thats really not how it works, however, you are correct, manufacturers put as minimal paint as possible on so you really shouldnt be flatting and polishing. in fact, id bet to use 1500 sanding this its already been painted before. When respraying anything to a decent standard, 4 coats of lacquer then you can sand it back properly :)
@PatricioGarcia19738 ай бұрын
you only remove less than a tenth of a micron of clearcoat.
@juansaladzar7 ай бұрын
Easy way? This is a ton of steps & very labor intensive brah 😐
@davidmichael3189 Жыл бұрын
Might as well buy a new Bonnet
@keithpeterson3805 Жыл бұрын
Yeh lol this amount of fucking around may aswell just sand it back and repaint it
@misssummersalt Жыл бұрын
How long should we wait for the clear to dry before doing any sanding?
@customspraymods Жыл бұрын
This was painted the day before.
@sthildas4857 Жыл бұрын
The longer the better...CSM says the day after with new clears 👍
@charliedurham201110 ай бұрын
That shit looked horrible at the end..all kinds of haze and scratches..was this a joke?
@keithpeterson3805 Жыл бұрын
Why polish a turd. Best way to fix clear coat is to actually fix it.
@customspraymods Жыл бұрын
Pro. Obviously👆
@keithpeterson3805 Жыл бұрын
@@customspraymods been a spray painter for 21 years mate lol