Sparex Ferguson TEA20 # 18 Servicing the Timing Cover

After removing the timing cover n through changing the crank seal and governor shaft seal.
Here is a link to the Kangaroo Stew where I bought it and got it running.
• Kangaroo Stew # 165 I ...
Some of the links I talk of in the introduction are below.
Queensland Tractor Spares Web Site:
www.queensland...
Queensland Tractor Spares Ferguson Parts Category Short Cut:
www.queensland...
Queensland Tractor Spares Technical Tab:
www.queensland...
Queensland Tractor Spares Downloadable Sparex Catalog Tab:
www.queensland...
Sparex Australia Web Site:
au.sparex.com/

[@gbowne1]

Dad always said if you didn't make somewhat of a mess nobody knew you'd been working. Righto Lance, good one! :)

[@BundyBearsShed]

Good point, lol.

[@assumptavaughan887]

Hi bundy. If you use a little heat around the housing the govenor seal will pop out with a little leavering. I have removed a few that way. Brilliant video once again.

[@BundyBearsShed]

Thanks for the tip!

[@mikemarinell4148]

I'm 53 years old with my 1st tractor, a 1948 TO20 . I love it and need it badly, though I haven't even heard it run. Watching and learning from your videos is the best!

[@BundyBearsShed]

Best of luck!

[@transliv03]

You're a great teacher, Lance. Thank you for passing on your knowledge and experience.

[@BundyBearsShed]

My pleasure!

[@Tod_Unctious]

What a great video Lance. Very helpful and informative. You will be responsible for a plethora of te20's all being refurbished during lockdown. As we all follow along with your great videos. Great work. 👍👍👍👍👍

[@BundyBearsShed]

Hope so!

[@darrenblattner2508]

The front seal is leaking on my 245, I was hoping there was enough room to change it without pulling the front end apart. After watching this I don't think that will happen. Thanks for the videos Lance, keep smiling.

[@BundyBearsShed]

No I dont think you can as it is in from the back too from memory.

[@paulbuxton5583]

Nice tutorial again Lance, Thanks, Paul. Surrey.

[@BundyBearsShed]

Very welcome

[@mikecoster4703]

Hi mr bundy...i have a tea20 having trouble with Governor not working great...turned the adjuster screw in til touches..doesnt do anything..turned it in 1 full turn works a little..do i keep turning it in until it works the way it should????

[@BundyBearsShed]

There is a video where I set up the governor on my gold FE35, exact same process, start there wnd work your way through.

[@peterdabrowski2328]

Hi lance. Is this the same process for the mf35 petrol? Do u think I need to remove the front axle as well?

[@BundyBearsShed]

Yes the exact same job.

[@johnkinnane547]

G'day mate just a question, why do they still use leather in the seals especially if they become very hard, and have you ever cracked a timing case when you hammered the seals in? Great to see you mucking around in the bundy shed you can tell your in your glory. John PS how is your weather . Regards John I'm going into hospital next Monday the 18th

[@BundyBearsShed]

Leather seems to last well if it doesnt dry out. Weather is good, getting a bit nippy though.

[@charleshart6992]

Excellent stuff, looking good!

[@BundyBearsShed]

Thank you! Cheers!

[@markbray4537]

Hi lance , I’m just serving my timing cover and round the adjuster needle on the side of the cover seized up. Any ideas on freeing up as don’t want to snap the screwdriver slot off ?regards mark, learning heaps from your videos and have now stripped my tea20 !!

[@BundyBearsShed]

Try gentle heat and by gentle I mean a map torch not an oxy.

[@karllynam2612]

Hi Lance. Are there cast markings on the front of the timing cover re timing/piston position?

[@BundyBearsShed]

No you need to use the marks on the flywheel.

[@whalesongservices]

Lance, Are there any differences doing this with a TEF that I should be aware of? Thanks for the outstanding videos!

[@BundyBearsShed]

Yes they are different but there is a free workshop manual on my web site might shed some light on it for you.

[@MrRandyj72]

I notice the governor screw on my tractor is broken. I can't find replacement ones online. Is there anything special about that screw? Could I have one made?

[@BundyBearsShed]

Nothing special at all easily made mine is 1/4 unc

[@MrRandyj72]

@@BundyBearsShed thank you sir

[@PaulHigginbothamSr]

Mr Bundy's bear I have some sockets for square heads which would have made putting in that wired in shaft holder a bit easier

[@BundyBearsShed]

I have some but use them so little I couldnt find them, lol.

[@colinmew6695]

Why did you not jet wash or steam clean engine before starting this rebuild??

[@BundyBearsShed]

I want to keep the original barn find patina where I can.

[@TigerUNC52]

Hey Lance. Really enjoying this series. Wanted to let you know that this video is in the Fergie rebuild playlist twice.

[@BundyBearsShed]

.

[@bobwilliams7343]

I think your the same as me I,ve got thousands of pounds worth of spanners sockets pliers but always seem to end up with an adjustable spanner or what ever,s closest to hand

[@BundyBearsShed]

Yeah that seems to be the way it is, lol.

[@scottleininger2404]

Awesome

[@BundyBearsShed]

Thankyou

[@pm270100]

boo gee tek term//get the shit out /// leather is good more embedabity

[@pm270100]

EMBEDABILITY

[@BundyBearsShed]

Leather is a good seal for sure.

[@krishanthisandaruwan9063]

Can we use rubber seal for governor shaft?

[@BundyBearsShed]

Sure can.

[@krishanthisandaruwan9063]

@@BundyBearsShed thanks