Spec-D Head Lights for the Scion FR-S - Install Video

Find out More: ft86speedfactory.com/spec-d-bo...
------
Spec-D Headlights for the Scion FRS. This video walks through the install process and also shows how they will look when installed.
Additional DRL wiring tips are available at the website link above.
------
Snapchat - Ft86speed
Twitter - / 86speedfactory
Instagram - / ft86speedfactory
Facebook - / ft86speedfactory

[@gdyment]

I bought Spyders, but used this for clarity on which pins/wires are DRL vs Low/High/Park. Would be nice to know if/how you wire it to come on with both DRL and Low/High/Park though.

[@DustyShedGarage]

Them lights look gorgeous

[@MrAdventure96]

Electrical wiring is not my forte. I blacked as soon as I saw the wiring.

[@BigFatBabyLegs]

yeah i dont understand why it cant just plug into where the original headlights connected.

[@aaronsadventures23]

Also waiting for the HID install video as was promised in this video... Please!!

[@ikonzoro1075]

Thanks for the wiring instructions

[@HippoReacts]

Don't slice at the wiring and tap in there, use a needle and push through where the clip connects and push the wire that is clicked into the clip out. Once it is out you can tap into the wire there from the rear of the clip like the factory wiring. You can wrap it around where the metal clip is clamped onto the wire and secure it nice and tight. Then slide the metal clip back into the plastic clip. Click it into place and repeat for all wiring. You don't have to move the rubber moisture boot out of the way since the wires are so thin. It will fit slugly into place and the rubber moisture boot will act as an anchor for the wire. You can also solder that onto the metal clip end as well if you like. This is the best permanent way to make sure that the wiring is done right the first time. Nobody wants to take the bumper off more than they have to!

[@XthTerrorOfDeath]

Is it possible to buy the harness clip for the stock headlight and just wire it into that so it can be a kinda-oem install? Not a fan of cutting into the wires behind the harness if I ever go back to stock

[@NiTheGod]

do you have the HID tut? the one with drilling the hole and stuff?

[@DDzeal]

On your website wiring document, there is option for having boomerang always on using diode. Can you tell us what type of diode is needed? Thanks alot!

[@Taz_RCF]

where can i find the link to install HID's with the Spec D headlights? Also are the High beam lights built into the system? I am currently using an HID kit along with OLM high beam lights in order to maintain my high beam function

[@Gs_constructioninc]

Do you have a video on how to install an HID kit on this headlights??

[@JR007x]

thanks guys!

[@rodrjo13]

Are these plug and go or do you have to do some wiring? please need an answer so I know if I should buy or not.

[@LeoJr]

How do you install the HIDs?

[@josephalsayegh]

How do you install the HID please send me the link thank you

[@pooyammehr]

I can not find the video for the HID install on these headlights. Anyone has the link?

[@360undead]

Please explain how to wire using Diodes so they are always on

[@moderatespark7620]

I cant get my boomerang and turn signals to come on. Only my low beam. Help? He didnt go into specific detail on how to wire the boomerang to come on during daytime/lowbeam

[@OreoVII]

Getting that side marker off was not explained articulately at all. Good video otherwise.

[@ELITEANGEL17]

Where's the "other video" for hid install??

[@chriskardaras7451]

hey i cut the red wire so that i only have the indicators working from the headlights but now it is flashing way too fast because i think it knows the front indicators are disconnected? how can i slow it back down?

[@Dazaroy4445]

same trouble. did you find how to solve this?

[@ilikesubwayrina]

Just wondering, Would those fit on a 86 GTS (Australian Model)? The GTS comes with OEM HID Headlamps, and the connector pins are different, there is 8 instead of 6 i think..

[@SkippyRoberts]

It'll fit

[@ilikesubwayrina]

Thanks man. :)

[@zAce31]

Where is the tut for installing hID?????

[@mosesosuna]

Why does my high beam not work ok my projector

[@BigFatBabyLegs]

I'm not doing any of this. Why didn't they just make a harness thing that sits between the OEM harnesses???

[@jibaitaco]

waiting for the HID install video....

[@rustyshackleford6913]

Guys! Do the video on how to install hids in these!!! There's no guide anywhere!!

[@mkovac1984]

Wow, these don't fit with the Vortech kit? I figured the housings would be similar to stock.

[@dvious_86]

Same with full blown kit. I had to go back to stock or cut and reroute my intercooler piping.

[@Aaron-fb6mb]

@@dvious_86 can you explain a little more?

[@dvious_86]

@@Aaron-fb6mb the back of the housing on the OEM headlights clears the Full Blown Motorsports intercooler piping for the FRS. The BRZ housing is shaped a little differently and Full Blown will give you a silicone coupler to join those two pipes routed slightly different. Now if you have after market headlights the back of the housing on the passenger side won't clear the intercooler piping by a little bit. In my case specifically I had the Spyder headlights and already powder coated my intercooler piping. I wasn't trying to cut the pipe and add a coupler. So my only option was to go back to the OEM lights. I hope that helps.

[@alanroco1045]

My wiring harness didn’t match the connect that was to my car

[@ibangomez4486]

I Installed mine and the headlights are working fine, but now my tail lights aren't turning on, help?!

[@FTspeed]

Email us at [e-mail] www.ft86speedfactory.com/contacts/

[@SuperKenshi21]

I accidentally touched the ground wire on the positive slot and all my lights went off. Did I blow my drl fuse ?

[@EricKremer]

Did you ever get that fixxed or are they still dead? Something similar happened to me but I didn’t touch anything to anything

[@asherwong9417]

@@EricKremer same

[@drewking8446]

what if you wanted them for drl's, and low/high/parking lights? or i guess on all the time.. would you wire it to both the possitives (the top left and lower right)? or just one of the connections? my brain is farting...

[@pinedasentertainment2418]

Drew King im trying to figure that out😭

[@mountainbikeanddrone9064]

Did you try this wiring both drl and low/high/parking lights. ? Will this work?

[@meliodas4560]

​@@mountainbikeanddrone9064 You should be using a relay and diodes to do that. Or just buy the always-on module.

[@Davinkyy]

Not sure what I did wrong but it seems my high beams come on along with my low beams

[@JAWZPB]

The connector coming from my spec d doesnt hook up to any connector on car side.

[@colehayes3376]

I'm having that issue right now, did you ever figure it out? I think I've just gotta tap the spec d headlight harness into the stock harness and bypass the clips all together.

[@rejve9289]

Is it possible to fit these lamps into Subaru BRZ??

[@FTspeed]

Possible, yes. You will need an 8-pin connector to 6-pin adapter or you can spice each individual function. It is not quite plug and play.

[@JayFidju]

FT86SpeedFactory where do I get the 8 to 6 pin connector

[@zF3AR]

Hid install????

[@erroldc]

Need a wiring tutorial for 2017+ 86 install.

[@kohlmannn]

Multimeters are fantastic tools

[@erroldc]

Yeah we did that and it looks awesome, but the thing is that we’re trying to figure out how to keep the DRLs to stay on without turning on the parking lights.

[@angeljuarez9006]

Did u ever find the video or tutorial on the wiring?

[@erroldc]

No I haven’t, but my friends and I just used a multimeter and tested every connection to see which goes to which and it worked the only thing that we needed to test is how to keep the DRLs to stay on without turning on the parking lights. I believe or have seen the DRL wire is hooked up to the fuse box if I’m not mistaken.

[@Martykoi]

where can we buy these headlights?

[@FTspeed]

www.ft86speedfactory.com/spec-d-black-boomerang-style-headlight-frs-1522.html

[@daanatorres]

bolt pattern for frs?

[@Aaron-fb6mb]

5x100

[@SkylineGTr1627]

Highly disappointed in these lights. 1. Extremely dim at night 2. Clearcoat came off 3. Noticeable gap around headlamp when bumper reapplied 4. High beam flap gets stuck. Need to tap the headlamp to bring it down. 5. Boomerang faded out after 2 years of minimal use I am now i need of a left headlamp b/c of number 5....thinking about switching to Winjet. I forgot how I wired it and will need to undo the wiring...

[@dkaplan100]

Wish I could find my 10mm to do this 😂

[@peterwelsh6975]

Please stop telling people the wrong way to wire stuff in!!! T clips and strip and twist in places exposed to weather very bad idea.

[@brendanb7965]

69th comment

[@Tyborg425]

would it be possible to install halos into these?