Welcome to the Spektrum AR636 Receiver AS3X and SAFE PC Programming Series! If there are any questions, please leave a comment below! Thanks for watching!
@JoshWeaverRC5 жыл бұрын
Dave, Good luck with the series. I'm sure it will help a ton of people a ton.
@NoonzAirborneRC5 жыл бұрын
Awesome! THANKS Dave. For learning all this and sharing it with everyone!
@bchboy12065 жыл бұрын
Awesome this will give he me confidence to buy one and program it. Thanks!
@linhearts4 жыл бұрын
Thank you. I finally got the AR636 in my Avistar working.
@wmdayman4 жыл бұрын
Sir you are a godsend. Thank you very much for what you have done. I have all the material to program these receivers but being shown how is a blessing.
@TheRCAirMarshall4 жыл бұрын
William Dayman my pleasure! If you get stuck or need help leave a question in the comments!
@larrysteele19564 жыл бұрын
Absolutely the best "how to videos" on the 636 programming. I'm 70 and these videos made me seem like a 20 year old techie to the guys at my club. Friend has a used Eflite 1.2m Spitfire that he was fighting with. I listened as he explained problem to another flier. Then asked if I could take a look. I did the PROPER preflight check and found the gyro corrections were wrong. I downloaded a clean version and the version in his receiver. Comparison showed I was correct! Somehow the reversing of the elevator and ailerons had been changed. We reset his aircraft as a NEW model and reloaded the receiver.....Flies Great....Smiles everywhere!!
@TheRCAirMarshall4 жыл бұрын
That's awesome! Glad to help!
@ryano.87684 жыл бұрын
Thanks Dave, this is a big help in me re-programming my AR636 for my Eflite Ultimate 2 which came with messed up programing :)
@phillipchou39875 жыл бұрын
This information is very helpful. Thank you very much!
@marshallspahr84824 жыл бұрын
Great series! I am having problems with my AR636 arming after I've completed a successful binding and following your instructions/video. The only difference I can find is that now there is a newer version (1.6.1) of the SAFE Model Builder that I am using and the only difference I ran into with it vs your instructions/video is that when I am on the 'Switch Setup' tab, the 'Flight Mode with SAFE on' selection is grayed out and does not allow me to set it to 3 as you do in your video. Other than that difference everything else is the same and followed. After the AR636 did not arm up the first time I reset it and repeated the procedure by following your videos 1 - 13 again and had the same results. After two failures I did load the SRM file that was created and saved prior to making the changes with the SAFE Model Builder and it did allow the AR636 to complete arm up so it is something I'm doing in the SAFE Model Builder program that the AR636 doesn't like and preventing it from completely arming up. Any ideas? Thanks
@carlospaioletti78294 жыл бұрын
Hi Dave great information this whole series about AR636! By a chance will you also talk about heading gain? Thank you!
@rhuffines135 жыл бұрын
Dave i need a watch out for tree button
@TheRCAirMarshall5 жыл бұрын
rhuffines13 Not sure if I can help with trees!
@renelioeanjie14854 жыл бұрын
1000000000% thanks it took me out of my confort zone, and I will be using AS3X on my OV 10 BRONCO. {my Christmas present} 🎄🎄🎄😜😜😜
@thomasjent14314 жыл бұрын
Thank you for your instructive video on the AR636 Receiver and programming it! I have 3 of these receivers and one AR9030T (not in a model yet). I assume the A,B versions like AR636A are just later versions of the same thing? Our systems are working fine, but was wondering how, or if, some of the original programming could be programmed slightly different. Glad to be learning about this!
@TheRCAirMarshall4 жыл бұрын
Thomas Jent thanks for watching! The AR636A and B models are OEM receivers that were originally installed in a Horizon Bind And Fly model. There are some minor hardware difference and some of the very early AR636A models may be locked. If you are unable to register the receiver it is locked and there’s not much you can do with it. If you can register it, you should be able to follow along with this entire series without any complications. Let me know if you have any other questions!
@brianjones67494 жыл бұрын
Hi Dave, I clicked the Link for Safe Model Builder and got this notification on the RC Groups Site: RCGroups Message Invalid Attachment specified. If you followed a valid link, please notify the administrator
@jaynap19705 жыл бұрын
This is awesome. Thank you for taking the time to do this.. quick question,. Will this work for the AR7350 7-Channel AS3X Receiver as well
@TheRCAirMarshall5 жыл бұрын
The AS3X settings will work, yes. But things like the firmware upgrade and the SAFE model builder are going to be specific to the AR636.
@chrisfrombrisbane2 жыл бұрын
Appreciate your work. Thank you very much.
@youtubecreativ3 жыл бұрын
I have a problem with the Spektrum Receiver AR636. If I move it back and forth with 2 fingers, the ailerons move. If I fasten it with a Velcro fastener and for sure in the right direction, then the spectrum receiver will no longer work. Should I not lash it down with Velcro, but fix it with double-sided adhesive tape. Thanks for your information.
@ddfwaj4 жыл бұрын
Hey Ken, great series! What Telemetry is available from the AR636 or what can be added? Thanks!
@TheRCAirMarshall4 жыл бұрын
The telemetry is fairly limited on the AR636. It will send back Rx Voltage, signal loss, etc. and will also pass AS3X gain data. It’s not a full range telemetry Rx. The new AR637T sends back a ton of data!
@ddfwaj4 жыл бұрын
The RC Air Marshall ok cool yeah I was hoping it would also send back battery voltage too but this does not sound like it would correct? Thanks again for the help, looking at options as always.
@TheRCAirMarshall4 жыл бұрын
It won’t send flight pack voltage, no
@hamishgurung92834 жыл бұрын
Hi, I just purchased AS3X programming audio interface SPMA 3081, while using AS3X program app, once plugging the audio plug in mobile or iPad , it’s shut down after 3 seconds. I tried many times but still doing same and I can able to use app problem.will anyone explain why?? Thank you
@TheRCAirMarshall4 жыл бұрын
I’ve honestly never had very good luck using the Audio cable and now use the Bluetooth module when I am connective via Mobile. I know the audio cable had some odd requirements, like the volume had to be turned up all the way for it to work right. Maybe try that. If the app is crashing, you may want to consider trying the Bluetooth module.
@davegogo103 жыл бұрын
@@TheRCAirMarshall In the overview of the AR636B Product Detail (enter SPMAR636B on Horizon search panel) Spektrum states that "due to the changing nature of Android FSK modulation its no longer compatible with the 3081 cable" and so to use the SPMBT1000 Blue tooth cable. However the manual has not been amended to this fact. Spektrum should be absolutely ashamed of their standard of documentation as if information is not omitted - then its fraught with errors.
@JamesLewis-mp9zn Жыл бұрын
Have you ever used one for a helicopter in place of a gyro?
@marcoliantonio4 жыл бұрын
Hello 👋🏽 ! Thanks for the video. I am an Italian and I have a serious problem with the Spectrum app. When setting the RX with the app, is the server connected to the RX? Because the manual says no. I have an eflite cirrus with dx8, I tried to configure the RX with the app, I moved the flap command to another channel and through the radio I can't fix it. do you have any advice for me? thanks
@treadhead19454 жыл бұрын
Hey Dave, if I wanted to assign the flight mode switch to AUX 1, how would I do that? For now I have a Dx6, which won't give acess to AUX 2. Thanks a ton, this series has been invaluable to me as I muddle my way through my first ARF build
@TheRCAirMarshall4 жыл бұрын
treadhead1945 what type of airplane are we talking about? Is it a full house, with throttle, aileron, elevator, rudder, flaps, and retracts? That will help a bit in offering up some suggestions.
@treadhead19454 жыл бұрын
@@TheRCAirMarshall this is the Hanger 9 Hellcat. Throttle, aileron, elevator, rudder, and retracts
@TheRCAirMarshall4 жыл бұрын
Got it! So if all you want is a flight mode switch, (you don’t have enough channels for a separate panic button) you would set up the AR636 to use Aux 1 as the flight mode switch and in your transmitter set up whichever switch you want to be the flight mode selection switch to the Aux 1 Channel in channel assign.
@treadhead19454 жыл бұрын
@@TheRCAirMarshall looking at the flight mode switch in Spektrum Programmer, the choices are unassigned, Gear, aux 2 3 and 4. I currently have it at unassigned
@TheRCAirMarshall4 жыл бұрын
@@treadhead1945 gotcha... That is a limitation of the Spektrum Programmer Software. Even if you do not intend to use SAFE, you can work around this by using the SAFE model builder application. In the Spektrum Programmer, you'll need to export the model you're working with by going to Models, then on the line of the model you're working with click the More button on the right side of the model line item, and click export. Save the file somewhere you can remember it. Next, open the exported model file in the SAFE model builder, and under the Switch Setup tab, you should be able to select "Use Standard AR636 Flight Mode Switch" and select Aux 1 as the flight mode switch in the selection box on the right. Save the newly modified model file and import it into the Spektrum Programmer. When you look at Flight Mode switch, it will show nothing at all selected. This is okay. In the actual XML code of the SRM file, if you care to look, on line 1501 of the code you will see "flightModeSwitch": 5, - which tells us that the flight mode switch is Aux 1. In the XML code 4 = Gear, 5 = Aux 1, 6 = Aux 2, 7 = Aux 3, etc... You should be good to go after that!
@stevewooten2624 жыл бұрын
how can I assign a switch and mix the r knob for the gain adjust?
@TheRCAirMarshall4 жыл бұрын
steve wooten this is an awesome question. In order to reduce confusion I would rather not answer it in a public forum. That’s fairly advanced and a bit outside of what Spektrum recommends and how things were designed to work and there are some precautions as well that I would rather address privately. Please shoot me an E-Mail to rcairmarshall@gmail.com and I will let you know how to do it there. 👍
@alexzarnas43864 жыл бұрын
Does this work for AR636A or AR636B receivers pulled from BNF planes?
@TheRCAirMarshall4 жыл бұрын
Alex Zarnas yes, it does! With rare exception this series applies to Open Stock retail AR636 receivers, as well as AR636A and AR636B receivers found in BNF models.
@edwyn13264 жыл бұрын
How do I make the As3x work for me? I create the 3 models and in none of them when moving the plane the servos move in the only way that works is if I increase the value above 50% to the head gain but when flying it does not correct me the flight because I have activated the head if you can help me I would appreciate it is an AR636B receiver
@ConservativeUSA674 жыл бұрын
Hi Dave so you post to my question on HH FB forum got removed. It was such huge help yet not sure why the removal ??? This is what I wrote back to you. So I wanted to say thank you but now no longer can read your well documented explanation with my v900 safe launch issue. This was my response. Igor Julian Kos badge icon Author Dave wow, thank you for this beyond comprehensive explanation and your kind help. I have three planes that I use Safe on and no problems right out of the box. The Timber X I barely use it on, the F16 during hand launch is a life saver and the v900. So reading your input (twice 😉 )as well as watching your video I do understand it . Especially with the throttle to elev. mix. The v900 is the first plane that Safe is giving me problems during launch, basically I launch at 3/4 throttle on a 4s or sometimes little less like 1/2 Throttle and it is then when the plane starts to dip down in safe and I quickly reach with me left hand to pull full back on the up elevator and it is still not enough to get level flight nor a climb and she is heading for the ground ever so slowly. So my instinct at that stage is not to give more power as suggested by others and I actually know that would pull it out of the dive as that is sort of scary to do in my case so I flip safe off (gear switch) quick and she pulls up fine and then I'm in full control. No issues with rolls, only pitch. When I'm up in the air and hit safe at a safe alt. and I test safe on it actually does what it is designed for and does not nose down and keeps leveled flight and limits my bank angles as it should. I spoke to HH and explained this and they sent me a new AR636 thinking the gyro may be bad but the new unit does the same. They even programed it for the V900 and now It is placed exactly as the BNF had the previous one installed and matches the Model Builder mount instructions as well. Same thing happens again so my solution was hoping for more up elevator travel while in safe so I can keep level flight and even climb in safe. So watching your video I still was not sure what to adjust . I saw the Thr to elev. mix and left that alone as I know that as thr increases pitch will go up and down elevator is needed but during flight when I went to full thr I did not get any crazy nose pitch up problems so I left that be. The only thing I though of that would help is to up the Flight mode 1 Elev pitch angle from 45 to 60 as I assume the higher number the more up elevator. Now I did notice more up travel on the elevator on the ground when safe is on but now I question that move because it could also mean that this change could perhaps make the v900 go into a climb now during safe, which actually I could handle better as down elevator has super throw. So to be honest I do not know if I helped the situation or not. As you said it is not complicated but the first time making adjustments to safe without an actual flight I do not know what this launch will be like. The F16 I can throw that like anyway I like and that plane levels perfect at any throttle or angle thrown so that spoiled me. I made it into a belly lander why the hand launch. Almost always the f16 gets launched at full thr but never ever dips, just levels. So now the only change I made to the v900 is the 45 to 60 pitch axes increase and honestly I do not know what to expect. So sorry. These are my unchanged thr to elev mix settings below. Again I so appreciate your input on this. Huge help but coming from Nitro days and Futaba FM 4ch in 1984 this is a little change up 😉
@gregdee5304 жыл бұрын
Can you confirm the DXe tx will work with this Rx and the re-programming?
@TheRCAirMarshall4 жыл бұрын
Depends on the DXe, I can only speak to the DXe that is purchased separately, not the DXe that comes with ready to fly models. For the DXe that is purchased separately, yes it will work not problem. You may have to do some reprogramming of switches, but the transmitter will work.
@gregdee5304 жыл бұрын
@@TheRCAirMarshall thanks, I should have mentioned it came with an RTF Carbon Cub+ with safe, as3x, and gps.
@TheRCAirMarshall4 жыл бұрын
Gotcha, I’ve never reprogrammed a DXe from an RTF model, but my understanding is they aren’t as capable. Not sure what the differences are. They will definitely bind to an AR636, but getting it programmed with the switches where you want them could potentially be a challenge. If it will program like any other DXe it should be fairly simple using the Bluetooth module or the USB Programming cable to get the DXe set up the way you need it.
@gregdee5304 жыл бұрын
@@TheRCAirMarshall I have contacted HH etc many times and can't seem to get a definitive answer on what it (Cub S+ RTF DXe) can do or be adapted to. I have thought about buying an OE spare part in the rx items in the Cub S+ and binding to that which I'm guessing should logically work as it can't see what model it is in provided the orientation and mount is identical to the Cub S+. A TX in Australia on a DX6I or similar is over $300, but I may have to end up purchasing a stand-alone Tx like that to be able to put safe/as3x in other models it seems. I'm a Mechanic by first trade, and now a builder, this Electric mumbo jumbo does my head in frankly lol.
@chuckyfreebirdking87093 жыл бұрын
will this include the ar636b i just crashed my aeroscout sunday and want to buy the fms 1800mm ranger pnp.......thanks
@TheRCAirMarshall3 жыл бұрын
Yes 👍
@chuckyfreebirdking87093 жыл бұрын
@@TheRCAirMarshall thank you
@SuperMagnum20117 ай бұрын
Thank you . 🇬🇧
@Santanig54 жыл бұрын
Dave, there is a large community at www.rcgroups.com/forums/showthread.php?2135213-Eflite-SAFE-RX-in-another-plane who can help answer questions and provide guidance for your viewers, Flightengr is certainly a standout among them. The thread was originally created by Jim Suenaga who transplanted the original EFLR310013 SAFE receiver from the E-Flite Apprentice into a E-flite P-51D "Dallas Doll". The thread has come along way since then and has most likely influenced the SAFE product as a whole. Glad to see someone has created a video series, but keep in mind that we learn new things all the time about the technology and the forum will have the latest information. Cheers!