One of the first items to check in the case of these problems, very common turbo seal fail
Пікірлер: 42
@shiyoushi57785 ай бұрын
Can you believe I was quoted $500 of labour to fix this seal in my sprinter? Glad I found this video, even I can follow along with this.
@VanlifeTroglio Жыл бұрын
what code was this one throwing?
@yogib373 жыл бұрын
wow welcome back. been a long time hope you doing well. I wish you were closer to me so you can help me change out my Key tumbler
@Bmx19ride Жыл бұрын
This was beyond helpful! I'm so glad I found your channel!
@timpearn93833 жыл бұрын
I enjoy watching your work! I think you may have forgotten a cover under the airbox? Or is that not needed?
@xmas42032 жыл бұрын
I saw that too. But at least now I know how it looks and how to best take it apart to replace that turbo intake seal.
@ManWander12 күн бұрын
i'm surprised that hose did not blow off from the pressure after you greased it
@scottelmore14273 жыл бұрын
Was it your intention not to replace the metal shield?
@tradmanmike33602 жыл бұрын
SO GRATEFUL TO FIND YOUR CHANNEL! NEW SUB. FROM USA 41... ALWAYS THUMBS UP!!! THANK YOU SO MUCH FOR WHAT YOUR DOING. YES!!! DO IT YOUR SELF IF YOU WANT IT DONE RIGHT!!!
@m.montgomery68359 ай бұрын
is that the same for Metris? I am experiencing power loss and MB service said that I need full turbo charger replacement. I started having this problem after injection cleaning service.
@morrisletshepa282 Жыл бұрын
Mercede benz sprinter 315 2010 leaking engine oil from exhaust pipe
@ebutuoyebutouy3 жыл бұрын
Thanks for sharing. Stay safe.
@jbcali16179 ай бұрын
I'm in love with the clarity, sensibility, responsibility, and accent ❤
@stevebays616 Жыл бұрын
Hi, very great videos, i have a vito v6 2008, I have a intermittent power loss, mainly first thing in the morning, i will change the turbo seal as per video and clean the EGR valve, i have also been told there could be issue with pipes and an air sensor, do you have any videos about the air sensor?
@morrisletshepa282 Жыл бұрын
Mercedes-Benz sprinter leaking engine oil from exhaust pipe
@robertlewis3712 Жыл бұрын
There was a panel under the air box. Why didn’t you reinstall it ?
@iandorling Жыл бұрын
Could wire the switched wire of the camera to another switched wire in your van so when you turn your ignition on you get a live camera image while van is switched on
@christopher61613 жыл бұрын
YAY no toyotas lol You have to admit most MB parts are FAR superior quality, especially things related to safety like the doors and clamps etc
@oldmcguy Жыл бұрын
Thanks, I am beginning to understand what is going on:
@rahhalettahiti46352 жыл бұрын
all great but you have forgotten the lid that is under the air filter and above the turbo
@a1superkeys4822 жыл бұрын
Hi had you heard something about that, I get a 2008 dodge sprinter 2500, I’m getting the code 2641-008 B60 (Exhaust back pressure sensor ) plausibility error, I just change the sensor and still the code it’s coming back right away it’s cleared, I Check the three wires plug connector, looks ok 5v, solid ground, good continuity signal wire to the Pcm, I put some extra ground from the battery to the frame and motor, Pcm case and nothing, i tested both sensors in another car and works good, the lifedata is showing always 5000 hpa or 72.3 psi i think it’s a default value. I check in the other good car and shows the same with the plug disconnect. Any of you guys has heard anything about that, any ideas what could be, That one is in limp mode also doesn’t go over 60 haven’t boost pressure, thanks
@rangerousy Жыл бұрын
Did you ever get it fix , my sprinter just started doing the same thing, and also it doesn't go over 60 either
@becoacamba6133 Жыл бұрын
@@rangerousy greetings, I get it done doing Egr & dpf off, but maybe are another options, I did that because was the most quick and cheap for me.
@fix63502 жыл бұрын
Could it be that this is why the vehicle smokes black?
@loudring62472 жыл бұрын
No, that's most likely your pdf not doing its job. Might need to clean it or replaced. You can run some liquimolly fluid in your pdf and do a regenerate the exhaust system should help clean and burn off excess ash buildup.
@supersaulflores4055 Жыл бұрын
You may have bad injector copper washer.🤔
@Neverstopfishing_A_M_ Жыл бұрын
Hello, nice video, do you have one for the turbo actuator repair?
@ricardopena90132 жыл бұрын
I have the same problem my 07 sprinter 2500 loose power i replaced that and same problem I don't whats next to look someone told its maybe catalytic clogged I don't any help ?
@loudring62472 жыл бұрын
No, that's most likely your pdf not doing its job. Might need to clean it or replaced. You can run some liquimolly fluid in your pdf and do a regenerate the exhaust system should help clean and burn off excess ash buildup.
@jean-marctorrini41772 жыл бұрын
Sincerely a great thanks from France !
@drsony82 жыл бұрын
You forgot to put back the engine top cover 😀
@michaelt29612 жыл бұрын
Great video. Could you tell me the type of silicone grease you are using? Thanks
@khalidelkharbachi61262 жыл бұрын
Thank very much for this clear explanation!
@richardspringer3440 Жыл бұрын
V. G. Thx
@ricardopinto17653 жыл бұрын
I'm having a problem in a 313cdi sprinter at work engine light flashing van don't push at all loses power very very much... That's can be my problem? 🙏
@lovekeshsharma19992 жыл бұрын
Hives, I have 313 cdi 2003 model . It is going in limp mode on hill . Need to stop engine and start again then it’s works again. How you sorterd your problem? Any idea.
@brunogoeseverywhere9082 Жыл бұрын
Hi, we have exactly the same problem! Have you been able to solve this?
@mareknosek93773 жыл бұрын
Amazing content !
@kenmackenzie73383 жыл бұрын
Hi great video, thanks. Was that the cause for the limp mode?
@thereissomecoolstuff3 жыл бұрын
I would have flipped and siliconed the turbo seal. Really enjoy your videos. Keep them coming.