Spyder Auto Installation: LED Halo Headlights Install Overview

[@royblckbrn]

Easily the best explanation and video that I have found on this. I have watched a lot of videos. Should have started and ended with Spyder.

[@Fukuyoutube]

I just quick spliced the led lights to the low beams since I have daytime running lights and didn't want the halo lights during the day....and quick spliced the halo wires to the running lights since they are off during the day....no need to have volt meter hope this helps!

[@tylr577]

I know this was 5 years ago, but I just got a set of headlights like this so I might as well ask. Did you use a CCFL converter at all for that or was it really as easy as connecting those wires like you said above??

[@andrews6411]

If you are worried about cutting into OEM wires I'd imagine buying a headlight socket extension harness wouldn't be a bad route to do the splicing on

[@Mac10.]

Do you take those little white caps off

[@theflossy7696]

Hi I bought BMW 06 E90 3-Series 4Dr Sedan Black Dual Halo Projector Headlights Lamps what type of gauge should the connectors have?

[@tommyd6665]

Can you tap into the headlight harness ?? Or just the turn light signal harness??

[@danboy0481]

I have 2010 GMC sierra. Would I remove the DRL fuse so that only the LED and HALO are on during the day?

[@1JayTheJet]

When I hook only to the battery to check the lights only thing come on is the LED and no Halo. Do the connectors have to be connected to the Halos when checking with battery? My battery is in the trunk and is to far to check with connectors on. HELP PLEASE... ANYBODY

[@Jake.24v]

Great video!

[@VeeNYC]

awesome explanation... spider is the best..

[@nicolevogt9042]

are the quick connects being used all 16-14 1/4 size ? I assume they are as they are blue and usually color coded to size. just wondering as and the wire gage of the red and black halo wires are much smaller in gage size from the ticker white and black led gage size it would not split the wire to much while it splits into it or would it even catch correctly and be able to close?

[@JeffCalloway]

Matt Cobb - Did you use a CCFL Inverter

[@88holstein]

On my lights for my 2002 civic, there is no white wires at all. Where do I connect the black and red wire to?

[@royblckbrn]

Black is always ground and any other color on the lights will be power.

[@mcalhad]

This video leaves me with 1 big question: when you use the quick connect and connect the red and white it looks to have a white wire coming out of the other side of quick connect which is needed to connect this to the parking lights....is this wire a seperate wire or part of the 2 white wires you splice into the quick connect just made one white connect back up on one of the white wires.....the same for the black wires..that is what has me puzzled.

[@michaeldevaney73]

i got 2014 dodge how do you hook the Halos up on my new lights I got three red wires two whites and 1 black how do you hook up the wire

[@andrewwitter4200]

U ever figure this out? I have the same issue

[@Durrelliful]

What if I dont have white and black wires? I have the black and red, but no white/black...

[@spyderauto]

Black and Red wire are for the HALO's White and Black are for the LED's Black - Ground White - Positive Red - Positive

[@michaeldevaney73]

+Spyder Auto i got 2014 dodge ram how do you hook up the Halos and lights I got 3 red wires two white wires and one black wire how do you hook them up

[@88holstein]

Have you found an answer to this yet? Spyders response doesnt seem to answer your question.

[@flex7224]

my halos dont have black/red they have white/red. So when I go to splice my halo wires (white/red) to my LED wires (black/white), would I connect red to white and white to black? Just doesn't seem right connecting the white halo wire to the black LED wire.

[@Razaille]

Is there a guide to replace the bulbs for the low and high beams?

[@Shadoefax760]

They don't need to be replaced, it's rare they ever burn out. They'll outlive the car.

[@MrKL83]

My bright halo ring ain't working. What gives?

[@jacksagrafsky4936]

On my Spyder halo headlight the turn signal/running light goes from the back of the fixture to the front corner leaving a amber two wired bulb in the rear with a two wire lead that ends at a gray connection. Now I can not find the matching plug for this bulb and wonder if it can be connected to the running light wires at the halo and led bulbs connection.

[@_valve]

Why don't they just come finished, Ive done everything the video says and they still don't work

[@johnpadula2983]

They're directions suck they don't even give you directions for the type of headlight they send you

[@rburnette9]

I’m dealing with the same problem. The directions don’t match and the only black and white wires run back into the headlight and don’t hang out like in the video. Very confusing

[@dravenpace8723]

John Padula for real!!! Especially on the instructions they don’t tell you shit about wiring and that’s the most important part!!!! No one needs to know how to put bulbs in that’s the easiest thing to do

[@hershelwilkerson4230]

This video is not thorough enough and it sucks for someone who doesn't know anything about installing headlights. It skips steps for the sake of time. Please try again

[@خالدالشهري-خ7خ]

Headlights ford explorer2006_2010 ??????????????????????????????????

[@rubydell6192]

These headlights are trash, trust me spend the extra money for better quality headlights.

[@Shadoefax760]

It's become so much easier than this, literally plug in new & done. Most fools have problems because they order what they think are correct lights for their car when there wrong. Use vin to order your parts. It's not this hard at all. Literally plug into existing plug once you removed old headlights.