Stage6 R/T Variator Installation || Piaggio Zip AC to LC

[@oscarharrison9100]

very useful video, thank you!

[@trentroger9923]

Instablaster...

[@jmcci2069]

Excellent Job 👍👍

[@zoekaran]

eutixos uparrxoun kai tetoioi youtubers kai ksefeugoume apo tin routina tou beauty kai tou katanalotismou! evge

[@MrBerenguer67]

Hi Thks for your excellent video whitch pressure the Waite spring on malossi kit thank you

[@binostuning]

This is not a mallossi kit

[@tarace9997]

C’est quoi la petite rondelle que tu a mis avant de remontée le vario ,j’en est aussi un avec mon multivart mais je pensais que c’était une bague de bride ?

[@MrBerenguer67]

Hi mate thks four your video i have a Piaggio Zip 50 2t when i drive and give a full throtle the speed cut down i cleaning the caburettor and i change the spark plag and still the same this happen to you thks

[@binostuning]

Thank you! Check your fuel lines that go to your carb, check the jets or look for air leaks at your intake or crackshaft seals.

[@kyledavies3101]

Could you show us a video of the bike running?

[@binostuning]

Extract yes I will film a video today Tomorrow it will be on KZbin

[@yilberthgomez3438]

@@binostuning g

[@MrBerenguer67]

Thank you for your video whitch size rollers you put in also whitch speed you get thks

[@binostuning]

I'm using 5.8gr rollers for stage6 streetrace with primary gear kit for more speed. Revving to 11K rpm and top speed ~130kmh

[@ants4193]

when you switched your belt from the standard piaggio one to the malossi one was there a big improvement? and is it okay to use this variator with the standard belt?

[@binostuning]

I think I didn't see any improvement other than the better longevity. Yes it's ok to use the standard belt with this variator, unless you have the complete overange kit installed.

[@youtubenutzer6236]

Does the Malossi belt your using now goes up to the highest point of the rear pulley? Im searching for a belt that is longer like the original so I can use the full 134mm (Same like oversized kit) of the rear pulley diameter. My vario ist big enough for a longer belt but I don’t know the perfekt length

[@binostuning]

I don't know if it goes all the way up on the pulley, I haven't measured it. But if your looking for a longer belt, search at maxiscoot or get an oversized one that matches your preferred length.

[@hakont.4960]

Dude, never tighten nuts with an impact driver, unless you actually limited it's torque somehow.

[@binostuning]

My impact have a torque choice.

[@hakont.4960]

@@binostuning Ah, should work well then.

[@deurlii7920]

Those bolts secure parts spinning upwards of 15000rpm, trust me you want those tight tight.

[@rokpavlic2575]

When im putting the variator in and then the pulley gets in a bit hard and when i try to electric start it .. it makes crunching noises and its not suiting so what do i do?

[@binostuning]

something is not fit properly or the teeth of the starter motor are worn

[@R_T_Remko]

Why you put the bigspring upside down??? Its not good metal on letal in clutch.. ( sorry for bad english)

[@binostuning]

Yes this is true. Is wrong to put it this way. The correct way is the opposite but I don't have it in the video.

[@R_T_Remko]

@@binostuning you switched it I hope haha

[@binostuning]

@@R_T_Remko yes I did. Also the stock black spring fits better for my setup.

[@R_T_Remko]

@@binostuning what is your setup?

[@binostuning]

@@R_T_Remko Now I'm running stage6 Street race cylinder just with port matching, yasuni c16 pipe, stage6 R/T variator, stock belt, stage6 sport clutch, mallossi clutch bell, pwk 26, stage6 reeds valves and block, polini primary gears, electric water pump. Probably 10-12hp

[@matis_5828]

Hi can you tell me what is the weight you put in your variator plz

[@binostuning]

They are 5.8gr

[@matis_5828]

@@binostuning set up ?

[@binostuning]

@@matis_5828 you can watch my latest videos

[@scottgehlken2330]

where do i get these parts

[@binostuning]

maxiscoot.com

[@АндрейНауменко-ж7г]

Hi, what variator belt size did you use with this RT variator?

[@binostuning]

I was using the standard Piaggio belt but now I'm using a mallossi one, I don't remember the size.

[@АндрейНауменко-ж7г]

@@binostuning thanks for help)

[@loca4159]

How mutch gram rollers comes with it?

[@binostuning]

6 x 3.5 gr

[@loca4159]

Thanks :)

[@jasonjod1ail]

Hey ik this video is old but what main jet are you running

[@binostuning]

On 17.5mm dellorto I am using 78-82 main jet

[@sunnybeachweddings7037]

How many grams are your rollers?

[@binostuning]

With my current set up is around 5.5gr

[@Objclips]

You put the clutch spring back on the wrong way👀🥴

[@binostuning]

Yes I realised that soon after.

[@Objclips]

@@binostuning no worries just thought I’d let you know pal 🤙👍

[@mohammedkarim8349]

How is That indicated