You're seriously the best at tech, you've saved me so much money through these videos
@gmbntech6 жыл бұрын
Thanks Orringe - great to hear. Any videos you want to see on the channel?
@orringejuice65116 жыл бұрын
GMBN Tech I'd like to see a video what all the knobs on forks and shocks do? Like high speed, low speed, bottom out, all of that because I'm so confused but I can't find anything on it online, thanks so much for all you help, keep up the great videos, thanks 😀
@laurentp896 жыл бұрын
Maybe consider buying a some merch from GMBN store then, that would be a nice and you can get some cool kit, just a suggestion.
@laurentp896 жыл бұрын
Great to hear, congratulations for the new bike.
@horrovac6 жыл бұрын
I (as Nicolai Lund-Jensen below) have a couple of issues with the process described. I'd take neither files nor sandpaper (nor polish for that matter) to the stanchions. Use a break-off knife (stanley, utility knife) blade and place the sharp bit parallel and against the surface at about 90° angle, and drag it over the burr. The stanchions have a hard coating so the blade won't "bite" into that, but it will bite into the (soft, aluminium) burr. You'll be able to get it absolutely flat and smooth like this. Then clean out the scratch (only here you can use some fine paper to rough up the surface INSIDE the scratch. Put your filler ONLY inside the scratch, don't get any around it. The stanchion coating is made to be porous so it can hold some oil and lubricate seals and bushings (not bushes). If you slather resin/varnish over it you're sealing the surface and degrading the lubrication in that area. Let it harden (in case of epoxy resin you can use your hair dryer to warm the spot up, this results in a harder fill. Then use the blade again in the same fashion to scratch off the excess resin/varnish. When applying the filler you need to make sure it is only inside the scratch, but makes a nice "bubble" above it, as it will shrink a bit while hardening. If you find there is a slight depression in your filler and you can't reach it with the blade, apply some more. When you're done, if you can, inspect the repair under high magnification. The filler surface should be dull, without any shiny spots. If it's shiny, you need to apply some more. Don't bother polishing, it is not rough enough to damage anything, and the little bit of roughness allows it to hold a bit of oil to aid lubrication. This process is fit for a functional repair, as it will restore the surface in a best way I know, however it's not fit for cosmetic repair as it will leave the surface of the burr shiny and thus visible as an imperfection. If you want to also repair it cosmetically, use an abrasion tool (a file or sandpaper) to lower the surface where the burr was, so it can hold some resin.
@leonlasic8606 жыл бұрын
Thanks for the preciced explenation!
@carraig0425 жыл бұрын
I like this much better and was thinking the same thing when I was watching this video. Will provide a better surface and less chance of making things worse!
@troytully56885 жыл бұрын
This worked so well for me. You can see the metal come off, go slow, takes 3-5 min per scuff depending on the depth.
@jusphit4 жыл бұрын
I like this approach! What kind of epoxy or filler are we talking about? i have a long scratch on mine :(
@horrovac4 жыл бұрын
@@jusphit I'd say any epoxy you are comfortable working with should do. In the meantime I discovered the UV-curing resin, that would be quite well-suited for the purpose. resin-expert.com/en/guide/uv-glue . Clean and fill the scratch, shine some UV on it and you can remove the excess immediately.
@nicolailund-jensen34536 жыл бұрын
Top tip: Use a sharp blade from a utility knife to remove the filler material. If you hold it parallel to the fork stanchion, you'll get the right curvature straight away and will save a lot of time on polishing afterwards(If you even need to polish). Bonus tip: The blade is hardened steel whereas the stanchion usually is aluminium, so you can also use the blade to remove the burr to begin with, which will again leave you with the same curvature as the stanchions. Works a treat.
@fearless29623 жыл бұрын
Is that without using the 1200 grip paper instead?
@zacharynield4822 Жыл бұрын
Any chance there is a video example of this somewhere?
@shiro-r4m6 жыл бұрын
I would recommend using regular steel needle files. Regular needle files will only take off the burr when light pressure is applied. Once the burr has been removed the file will skid across the surface IF you work with light pressure. The diamond coated ones are basically like sandpaper. They scratch up everything they touch. These coated files will scratch the surrounding vicinity of the nick and go straight through the anodisation.
@Cinnabuns20096 жыл бұрын
Im not familiar with the 'type' of anodizing they use on fork stantions but "Hard anodize" does come in black and IF its Hard Anodize, its upwards of 60 Rockwell hardness and your file won't do anything to it. It will actually damage the file. Have you tried this with a regular file? I figured Doddy suggested diamond files because this is in fact hard anodize.
@shiro-r4m6 жыл бұрын
Cinnabuns2009 the whole point of using regular files is to not mess up the anodising that is left around the nick. But aside from that, my files are 63hrc, which is a pretty standard value for quality files. The raised burr is aluminium and is easily removable with a steel file, when the burr is gone the file will just skate across the surface. That doesn't ruin your file by the way, unless you're exerting a lot of pressure on it.
@ShadowlordDio Жыл бұрын
@@Cinnabuns2009 Diamond files are harder than 60 Rockwell hardness . so you must use steel file
@rugludaIIur6 жыл бұрын
Great video. I've used a razor to remove burrs before with some success. Then the same procedure with emory paper and polish. Instead of nail varnish you can also use an epoxy which is a bit tougher.
@endurotruckererniedesjardins6 жыл бұрын
Try P O R 15 . Its a epoxy resin paint used for automotive restoration on anything rusty and old. This stuff is super duper tough paint. Stones off the tires wont even chip it. When i weld up a new trailer in my shop i use P O R 15 to paint it. Stuff last forever compared to paint. I used it on my 888rc and mt 66rc. Never know they were fixed. I have found the seal alway seems to need to be replaced once it runs over a nic and get cut by it. Change the seal and your brandnew secondhand.
@swatidey84823 жыл бұрын
You r really intelligent dude.👍👍 Keep sharing ur knowledge
@gogovitch666 жыл бұрын
Very helpful! 👍🏽 How long is this nail polish going to last on the stanchions? Thx
@Metal-Possum6 жыл бұрын
I started doing this on some 1997 Z1 Bomber stanchions. The gold anodizing they have on those things is hard as nails, some wet/dry sandpaper in a fine grade (800-1000) and a careless attitude made them smooth without affecting the coating.
@thechaosengine30206 жыл бұрын
When we transport bikes on the bike trailer at school we slam the dropper posts and put bits of foam pipe insulation over the stanchions and any other bits that look like they might rub. Cheap as chips and you can just tear it to size if you're in a hurry.
@mxandmtb22026 жыл бұрын
Thank you so much for this I just used this on my bike, and I was just about to get new forks Thank you so much 👍🏻👍🏻☺️
@heirilosman49266 жыл бұрын
Thanks for the video Doddy. Can't say I did not wince through the whole video. You are a brave man.
@PedroFTeixeira6 жыл бұрын
I've commented on a previous video, but I think you should look into ceramic coating, to see if it works.
@godfreytan10012 жыл бұрын
Thank you for the tip. Saves a lot of money and hassle.
@ViktorJ0van0vski2 жыл бұрын
So can i bassicaly use my girlfriends black nail polish ? Is that the same?
@dominichirst45186 жыл бұрын
Aluminium foil and water works really well to take out scratches. It is used on chrome so is really effective on forks etc. Flat square of foil, a bit of water and patience.
@arjunabernard81924 жыл бұрын
What metal polish did you use? I tried Brasso and it ate the epoxy right off.
@paulwolfram7774 Жыл бұрын
Hi Doddy, is this also gonna work on a small dent in the stanchion tube!? Many thanks in advance!
@henrik56375 жыл бұрын
Thanks for good video! Any chance you could make a video on how to service a dropper post e.g take it apart clean change seals etc
@p10tr3k74 жыл бұрын
Thanks for this video ❤
@generalhavok74866 жыл бұрын
One of the best vids ever! So valuable,thanks!
@djrouge33006 жыл бұрын
Fantastic vid Doddy
@civiprepper2 жыл бұрын
There is actually a repair that can be made with epoxy. I have also seen brazing rode used and then sand smooth. I prefer epoxy and then spray with a Teflon paint. Great advice here for smaller job's.
@shiro-r4m6 жыл бұрын
Restoring the surface of a precision component with sandpaper without any form of rigid, straight backing will create small lumps in the surface and alter the geometry of the stanchion. You will probably not be able to see the lumps but they are there and they will put extra wear on the seals. Please use a nice straight wood or metal backer to avoid sanding lumps into your stanchion.
@tone346 жыл бұрын
Sanding block on a round surface? dont know about that one.
@shiro-r4m6 жыл бұрын
If you feel so inclined you could certainly make a sanding block precisely matching a section of the circumference of the stanchion plus offset compensated for the thickness of the sandpaper and double stick tape/glue. I was trying to keep my comment short but I should have mentioned that low sanding pressure should be used. With care it's certainly possible to correctly sand a cylindrical surface with a flat sanding backer. It's for sure better than just using your finger.
@PP_Mclappins4 жыл бұрын
From my experience This is unnecessary when working with such a small scratch, if you take the time to work precisely and within the parameter of the damaged area. Doing This is a waste of your time.
@pathikdesai58533 жыл бұрын
Amazing idea but will this work for inverted forks of my motorcycle?
@nickwatkins52276 жыл бұрын
Great video Doddy hope I never scratch my stanchions but if I do I will now know what to do 👍.
@ZychuZychu6 жыл бұрын
I cant believe you didnt show the finished job :/
@Rudilink5 жыл бұрын
Agree
@SKBKER5 жыл бұрын
because it most likely looked shit . You don't put that much epoxy and you don't sand the dame stanchions . You put a dab of epoxy in the scratch and then use a blade to cut the excess away .
@大内大内高手4 жыл бұрын
我想知道这是什么胶水?
@CRYPTOGUYRY4 жыл бұрын
@@SKBKER if you watched it he used nail polish not epoxy and wasnt sanding ... 1200 grit dont sand son he did nothing you are talking about hahahaa
@陳民勝-z5z4 жыл бұрын
@@大内大内高手 指甲油
@p199a6 жыл бұрын
Should you use anything on your stancion like lubricants after every ride ?
@archetypex656 жыл бұрын
dd410 you don't have to do it after every ride but it should be part of your regular maintenance. I like to coat my stanchions with pure silicone spray (make sure there are no petroleum distillates in the ingredients some market theirs as; silicone spray when it's not really a true silicone spray) after every other ride. The most important thing is to make sure that the fork is clean there is no dirt and debris near the wioer seals. Once clean and dry spray a light coat of silicone being careful not to get any overspray on the brake caliper and rotor. I usually cover the brakes with a big towel. You don't need too be liberal with the silicone just one or two short sprays. Then just lightly wipe off the excess. Give the forks a few bounces and you're good to go. You can do the same for the rear shock as well.
@p199a6 жыл бұрын
thanks bro
@Mr.ZiggedWhenHeShouldaZagged6 жыл бұрын
Can also spray silicone onto cloth then wipe onto uppers. I use this trick for car door seals in Canadian winters to keep doors from freezing shut and avoiding a big mess.
@freerideinkmtb24204 жыл бұрын
How long do u recommend for the nail polish to sit before using? I know till its rock hard. But how long did u wait in this video?
@cosmicrebel47583 жыл бұрын
Thank you.
@Bad.Rabbit6 жыл бұрын
I think I'll start transporting my bike with the dropper slammed to protect the stanchion from now on
@Andy-tc2gt6 жыл бұрын
yeah definitely worth doing
@rp003.06 жыл бұрын
That's what I do plus it takes up less space!
@VanDungLe25106 жыл бұрын
Well, i'm just gonna roll an inner tube around that dropper stanchion. It's a hack. Seth's Bike Hack show this. How it works is kinda like a Gravity Dropper post
@th_js6 жыл бұрын
Yeah I always do it
@blazebraff91683 жыл бұрын
This helped so godamn much
@VanDungLe25106 жыл бұрын
What does the metal polish do ? I mean, after you've filed the scratch down, put some nail vanish on it, smooth the surface out with emery paper; it pretty much smooth at that point right ? And would silicon spray affect the metal polish ?
@felderosa6 жыл бұрын
Dũng Lê Văn it's just another finer level of sanding to make it even smoother
@satellitehunter74402 жыл бұрын
Could you use a gold color nail color to match the gold stanchion or only the nail clear coatings? Great tip, thanks
@Revexet2 жыл бұрын
did u already used gold nail polish ? or the clear one and it is totally fine without any problem of using it ? ?
@KiwiKiller886 жыл бұрын
I have a minor scratch on both my stantion and shock. I have filled in the scratch with nail polish then sanded and finally polished them. They are minor, but I can still feel them. Will I eventually have to replace these parts because they will wear through the seals?
@mrfailure936 жыл бұрын
Excellent video
@BRANDOAN4 жыл бұрын
Hi Doddy, any tips on working on a scratched kashima coat?
@happydoggo5925 жыл бұрын
Could you use a sharpie to hide the scratches after filling them
@cameronlesley24286 жыл бұрын
Fantastic tip, thanks
@clairefuller61442 жыл бұрын
What is a better seat for this bike?
@virkelie25 жыл бұрын
About spraying the fork with silicone spray - does that in any way interfere with the oil inside the fork?
@gregstinson57254 жыл бұрын
Technique seems to work fairly well. However, just one or two applications of polish hasn't seemed to fill the scratch. I've removed excess using a razor on my first few attempts, as others below have mentioned, but it might be pulling some of the fill out or leaving a small lip. This is possibly why the video just sands down the fill, rather than cutting away excess. I have a feeling this repair just buys some time as I can't imagine the polish lasts very long being exposed to oil, grease, and friction.
@ninjabolk96762 жыл бұрын
I have a question - the stanchion of my fork has a scratch but its barely noticeable but when I touch it using the tip of my finger nail I feel like theirs a ridge on the scratch
@nannattack Жыл бұрын
Can one use black nail polish? Does it have to be clear?
@Mcfc2Rich3 жыл бұрын
Should you buy forks with marked stanchions 😕
@theonlycranny4 жыл бұрын
Can you use black colourer nail varnish to match the forks?
@alf3071 Жыл бұрын
can you use superglue instead of nail varnish?
@madisonjenn21756 жыл бұрын
I just bought a pair of 160mm 36's with the intent to lower them to 100mm for a dirt jump build, they were cheap because there's a little gouge in the stanchion, but it's about 30mm above the fork seals so once lowered it will never rub over the top seal. Are there any internal o-rings I should worry about it rubbing against and damaging?
@_Steven_S6 жыл бұрын
Madison & Jenn it could rub the bushes inside the lowers if the gouge has rough edges.
@jasoneastabrook6 жыл бұрын
I didn’t even realise this was such a problem, luckily I have a brand new fork being installed to my bike right now so I will definitely be watching out for scratches now
@shanestarita38076 жыл бұрын
I have a Suntour Epixon 27.5 TR that I'm bumping to 140mm... how can I get it more progressive as it doesn't take tokens like RS and Fox?
@dlaps99754 жыл бұрын
Is it necessary to use the metal polish?
@fukcg00gle954 жыл бұрын
I know this is old but that's a sic wristwatch you're rockin. Noice 👍
@karlwilliamsart3 жыл бұрын
Looks like an old Oakley watch 👌🏽
@kay198336 жыл бұрын
Is metal polish the same as paint polish? you know, the same paint polish we use when working on car paint job?
@jrich20886 жыл бұрын
I just found a scratch last week! I’ll have to try this.
@RiderLasak6 жыл бұрын
U safe my money, thx a lot bro.
@rickclark78465 жыл бұрын
I have a set of forks and they have a gash in the stanchion that is clearly visible should i repair it ot leave it?
@christianhehir71296 жыл бұрын
Such a good video
@brandonaustin30406 жыл бұрын
Christian Hehir been out for 10 seconds how would you know
@MrAllstar6 жыл бұрын
Bit of a sloppy job if you ask me, not surprisingly we are not shown the end result which is normally standard practice for these kinds of video. For one I would stay far away from my stanchions with cheapie diamond files(very aggressive grit) and not slop nail varnish all over the place, nail varnish should be very carefully applied and only in the chip. Also you don't want to sand the good areas of the stanchion, so it would be wise to use masking/painters/tape to mask off everything but the filled scratch when you come to sand it and only sand the surrounding areas on the final smooth off sanding with ultra fine paper. PS.. you can get black nail varnish and all kinds of colors, I'm sure it's possible to find one in near the exact shade of most stanchions.
@Petr3884 жыл бұрын
do girls like to paint their nails with kashima colour? :D
@bongomenMAX4 жыл бұрын
Very usefull
@andi1831 Жыл бұрын
I try it
@joejoemtb8011Ай бұрын
Can you use black nail polish?
@samuelmiserotti59085 жыл бұрын
Love this channel,
@carlloin72635 жыл бұрын
What if you cannot feel the scratch? I got such I light scratch the other day. Can I just coat it with epoxy?
@elizabethmcdonald20206 жыл бұрын
could you use a colored nail polish to match then go over with clear?
@Trinity10iloveyall6 жыл бұрын
Elizabeth McDonald yes
@LongLiveEnduro6 жыл бұрын
Awesome quality video!
@gmbntech6 жыл бұрын
Cheers Chris
@2stocke9x6 жыл бұрын
I’m Looking to buy a newer fork for my bike, should I buy a used fork with damage (like the one in the video) and repair it (like in the video) so it runs smooth and I can use it, thanks.
@thechaosengine30206 жыл бұрын
I'd be wary of buying anything that's damaged mate. If a person is happy to sell something that is damaged I doubt they will have taken good care of it. And that's just the damage you can see. Too much of a gamble and you'll have to spend even more to get it fixed.
@gmbntech6 жыл бұрын
@Blake, like ChaosEngine has said, it's a good rule of thumb not to buy damaged stuff
@2stocke9x6 жыл бұрын
GMBN Tech thanks Im going to buy a undamaged fork, do you have any good suggestions for a fork with 150mm of travel or more?
@sushirolle4014 жыл бұрын
Does it work for the rear too?
@ethanbranchi17846 жыл бұрын
What would you do if you had a Fox Kashima fork, shock or dropper?
@braedenmurray35983 жыл бұрын
Same
@hunterwright3864 жыл бұрын
Great video, but you didn’t show us the finished product! How do I know what it supposed to look like?
@BobbyChainsawMarmot6 жыл бұрын
GMBN Tech, is there any disadvantage to using colored nail polish as opposed to clear varnish? My stanchion is black so I'd like to use black polish, but don't want to do so if it'll damage the stanchion
@Revexet2 жыл бұрын
did u did it and did it help ?
@BobbyChainsawMarmot2 жыл бұрын
@@Revexet Yep, I used black nail polish and it worked like a charm
@ViktorJ0van0vski2 жыл бұрын
Can i use my girlfriends black nail polish is that the same or i need this nail varnish thing?
@allanshpeley4284 Жыл бұрын
You can wear whatever color nail polish you like while you fix the fork.
@j.f.47656 жыл бұрын
Does this work with fox 36's kashima. Its doesnt feel rough. But I have a small amount of scratch. When I feel it, it doesnt feel like there are any scratches.
@Azkardt6 жыл бұрын
nice n' smooth af doody...as always :D great vid!
@braedenmurray35983 жыл бұрын
Thank you so much it saved me from buying a new fork.
@andrei37205 жыл бұрын
I just preadure washed my bike and the dropper post was going wierd down...like it rubbed on something. Im now home and i have a 13cm scratch
@kainpwnsu2 жыл бұрын
AH! I'm glad I filed this video away in case of disaster, and my ticket finally came up. Your guidance worked perfectly! I just finished polishing up a triple gouge I filled with a spot of clear epoxy. It looks like a tiny tiger took a swipe at my stanchion. My poor Fox 36s have a battle wound, but will wear it safely and proudly. Every ding cones with a story to tell! It would be great to see a video about filling dings in carbon frames. My Yeti Lunch Ride has many (many) miles on it, and has the scars to prove it. The white and occasional black scar really stand out against the turquoise paint. I assume automobile touch-up paint would work, but I'm not sure if it will negatively react with the carbon.
@engineerofalltrades5 жыл бұрын
I would use filler in just the scratch area not anymore like in this vid. All the polishing thins out the stanchion coating.
@driftordie00284 жыл бұрын
What is the lower part called and if it gets scratched does it matter
@zyoungson6 жыл бұрын
What happens when the filler breaks off inside and knackers the fork ?
@flickmybeans75075 жыл бұрын
New forks 😂
@SKBKER5 жыл бұрын
If it's done right it won't come off
@stevent15655 жыл бұрын
There are some who agree n disagree with this method based on the comments. I dont think either way is wrong but which is better depends on the nature of the damage. I found epoxy good for deeper chips but not effective on shallow chips. Nail varnish + super glue mix is very effective for shallow chips but needs to be done properly to last (i dont agree with filing the chip). However filing the burrs is not the best way. Using a very sharp stanleys blade to shave off the burrs is more effective n isolates the chip. Just fill the inside of the chip, use painter's tape n make a hole almost the same size of the chip n just paste it on the stanchion. It makes isolating the chip effective to fill in the chip without slapping the varnish/glue mix all over but only inside the chip and a bit around it thn remove the painter's tape when done. and LEAVE IT FOR 24 hours to complelely harden (best in warm room). This is extremely important or it wont last. Next use a harder thn painter's tape material like any excess frame protecter film, make the same size hole as the chip n replace it with the painter's tape so as to isolate the chip n the varnish/super glue mix. This is for polishing the excess filling with very fine emery paper without buffing the uneffected area. Dont use the blade to shave off the varnish as most of the time you will just pull out the whole filling. Keep light firm pressure with the emery paper n polish the excess varnish+super glue mix on and around the chip until it is almost smooth over. This requires a lottttttt of patience so dont rush it. This method require more steps n patience but it is well worth it n the chip is barely noticed. Mine has been on for the last 6 months with no issues.. even if it eventually comes off i wld do it again as the effort is worth it if it last a few months n save a load in buying a new fork. I guess a good nail varnish and super glue is the ghetto resin epoxy.
@justinrees51326 жыл бұрын
Useful
@florianheptner91963 жыл бұрын
How much of a problem are these scratches on a coil fork
@braedenmurray35983 жыл бұрын
Huge
@JogBird6 жыл бұрын
cool
@MrWaarden6 жыл бұрын
A bit too much nail varnish? You just need to fill the scratch and around 1mm outside the scratch. Then you don't have to sand it as much. Good vid as always!
@bluestraycat6 жыл бұрын
Great video Doddy, as always! I can't figure out though why you use brake cleaner with the sandpaper. Why not just soapy water?Am I missing something? Keep up the great work love your videos
@christianhehir71296 жыл бұрын
Much needed
@gmbntech6 жыл бұрын
Glad to be of help Christian!
@jacksonmississippi38576 жыл бұрын
Thank you ❤️😍🎊 you for your help
@gmbntech6 жыл бұрын
Thanks for the comment Baasir
@Iskrenm505 жыл бұрын
I have a scratch its very very small do i need to do that?
@obecyclist52392 жыл бұрын
What if the scratch is just a hairline? Do I need to do anything?
@8evvied4 жыл бұрын
My front forks are matte black, when they scratch the silver comes through and looks obvious, as long as the scratch isn’t too big a quick little fix is a black sharpie, doesn’t fully hide it but makes it much less obvious
@pugz38386 жыл бұрын
What if the scratch is above like the cashima print on a fox fork where u shouldnt be usin the last few mm of travel, is that just as important
@cup_and_cone6 жыл бұрын
Let all the air out and compress the fork. If it goes into the seal it needs addressed.
@pugz38386 жыл бұрын
thechosendude niceone g thanks f tellin me
@th_js6 жыл бұрын
Nice
@gmbntech6 жыл бұрын
Cheers Tomi!
@th_js6 жыл бұрын
Hi I have one question and would appreciate if you could answer it here, so I have a really really small nick on my stanchions that I can barely feel with my fingers (we are talking about less than 1mm) so do I need to do anything about it?
@rowanconnolly65306 жыл бұрын
#askgmbntech where do you get replacement sag/travel indicators?
@Nikica3586 жыл бұрын
ZIP TIE :D
@jtaraiza24806 жыл бұрын
zip tie or your local bike shop
@_Steven_S6 жыл бұрын
Rowan Connolly if you mean the o-ring it's in the full service kit, if you mean the 30%, 25%, etc gradings on the tubes.... new fork.
@stoenchu1226 жыл бұрын
Guys can you make some commentary over the new trunnion mount shocks about how you can brake on of the eyelets if you let on bolt loose and fucked up the thread? PS bad english, sorry
@Primarch_Vulkan6 жыл бұрын
#AskGMBNTech Hey doddy, how do I fit an ISCG chain guide/bash guard to my new Canyon Spectral if it doesn't have the mounting points on the frame? Thanks and keep up the great work on the channel.
@789oGaming6 жыл бұрын
The Flash I'm pretty sure you can't fit the one which has ISCG mounting. If that bike would have regular bottom bracket instead of pressfit you could install ISCG adapter. I have 2016 spectral and I have installed chain guide using e-type front derauiller mount.
@Primarch_Vulkan6 жыл бұрын
The 2018 Spectral has a SRAM GXP BB which I believe isn't press fit (not 100% sure as I'm pretty clueless when it comes to BB types) so I'll have a look into an ISCG adapter, thanks for the info.
@789oGaming6 жыл бұрын
I believe it is sram gxp press fit but not 100% sure. As far as I know canyon doesn't make frames with threaded bottom bracket option.
@chvhndrtntlr34823 жыл бұрын
hey where is the finished job? I know something going wrong here
@brandonaustin30406 жыл бұрын
Kind of prefer videos early 🤙🏼
@jackbeames76436 жыл бұрын
Can you do what you’ve done with kashima on fox forks. As I know kashima has something special about it??
@MrWaarden6 жыл бұрын
I bet u can do the same thing on a Kashima coated part.