My stihl had been leaking bar oil. in this video I show what I did to fix the problem.
Пікірлер: 27
@hikerdude52653 жыл бұрын
I have 026 and my pump is identical to yours. Amazon has pump kits labeled for 026 but the pump in much different then what is on this vid and what I, you, actually have. Viewers really need to be careful lining this up. Just because Amazon sellers call it a 026 or 024A pump, doesn't mean it is. If you are just looking for the intake hose and filter, (leaky part), this will work. This was really useful, thanks.
@johnclarke6647 Жыл бұрын
There is a big flat washer that keeps the clutch from tightening down on the worm gear and binding it up. It has the word “Top” stamped on it. The Top side goes outward. The oil system on the 024 is a constant running system. If the engine is running, it is pumping oil to the bar. I usually replace this system with one that only oils when the sprocket is turning, but it requires a lot of new parts.
@KRAMPUS_G60_16V Жыл бұрын
I have older version of the same saw with that problem. So just replace that oil hose, and hope it works. 🙂
@st76504 жыл бұрын
Thanks for the post mine has been leaking for a while large amount of bar oil once it sets over night all the bar oil leaks out.
@machigane79023 жыл бұрын
At 4:40 it looks like your needle bearing is damaged. And you should grease it when you have it apart before reinstalling (lithium grease).
@DennysCountryLife5 жыл бұрын
Nice work man! You basically stole that thing for $100. I still see them sell for $200+ around here. Good job on the fix!
@wayneberry87032 жыл бұрын
Great job mate
@duxburydom52284 жыл бұрын
Great video!, thanks. I'm green to saw mechanics. I unfortunately shredded my o24av oil pump, and everything up to the sprocket. i cant find a replacement anywhere for the oil pump. Is there an alternative setup, or OEM/used part you suggest I use for the o24av oil pump?
@bucksgarage14 жыл бұрын
I would look on ebay for parts. It surprises me stihl cant get you parts. Those saws are getting old though.
@jgbelmont4 жыл бұрын
I replaced one on my ms360......mine still leaks. Replaced oil cap also....still leaks.
@JasonTylerRicci2 жыл бұрын
I have an 024AVS (Super). I cannot find an OEM or comparable aftermarket tensioner for these saws. Any idea?
@lindaputnam96984 жыл бұрын
Not the right fuel line for the 024. Will need a straight one. That fuel line fits some of the 026 saws.
@bill154cub4 жыл бұрын
Don’t park Harley’s near your saws,lol
@keithsage15934 жыл бұрын
024 damn good saw..
@lucasskinner96734 жыл бұрын
Link to the parts you got? Did it hold up? Thanks i have the exact saw
@bucksgarage14 жыл бұрын
Haven't had a problem since. HIPA Fuel Line Filter Intake Manifold for STIHL MS240 MS260 024 026 Chainsaw www.amazon.com/dp/B06WWCVHBT/ref=cm_sw_r_cp_apap_jyq5VVXvynFPW
@WorldsOkayestFarmer5 жыл бұрын
Pretty good video quality up close! Hope china holds up for you! #WorldsOkayestFarmer
@Adlerwolf10005 жыл бұрын
How have u get out the oil pump? It looks like there is a ring on top ?
@bucksgarage15 жыл бұрын
There that is part of the clutch and it comes off easy.
@Adlerwolf10005 жыл бұрын
Oh ok. I have the same saw and I like to put out the oil pump but I can't get out this silver ring which secures the pump in the middle after you put out the clutch. Or is this ring part of the pump itself? I am not sure. Thanks for ur help ;D
@bucksgarage15 жыл бұрын
I thought you were talking about the clutch safety band. I dont beleive there was any ring that I removed before I took the pump out, just the 2 screws holding it in.
@Adlerwolf10005 жыл бұрын
So the silver ring in the middle on top of the oil pump is part of the pump? Because I took out the two screws. But it fits tight..
@bucksgarage15 жыл бұрын
As far as I remember. Here is a like to the parts diagram. goo.gl/images/YNMThr
@ClayBlasdel444 жыл бұрын
he left out the part where his installs the new part