stock 4910 compared to ported 4910

[@dubbssawshop]

I've said it before and I'll say it again, the 4910 Master!!!!! 👍🏻

[@Doc-Cole_Trickle-of-Chainsaws]

👍🆙D

[@justinweaver8107]

Agree

[@Bkellyusa]

Interesting video. It exacly matches the performance of the 4910 you ported for me. After your porting work it was almsot comical how fast that little, lightweight 50cc Echo could cut. Mine sounds exactly like yours as well. Thanks again for porting my saw. It really made a difference.

[@ragercrepair9301]

Man the difference is mind blowing! I thought a muffler mod and limiter cap delete was helpful on mine, but that porting is definately needed for the thing.

[@chrismuncey3861]

Holly 💩🤯 dude!!!. That's unbelievable.

[@mitaraho]

I picked up a new 4910, I'm waiting till after the first of the year and I'm overpaying you to make one up for me. Thank You Charles, Tim O'Hara

[@timberslasher4899]

Thats a big ol' difference!

[@dan-dan-da-treeman]

Amazing difference.

[@justinweaver8107]

Night n day wow!!!

[@jamesfarmer1523]

Pretty impressive.

[@crazyfeller5704]

I have a spare tank for a 490- not exactly pretty, but should hold fuel. Let me know if you want it.

[@sunbear1973]

👍👏 very good

[@tedneitzel]

Sweet!

[@JoshSmith-v1c]

Saw shouldnt crackle in the cut..a touch to lean

[@CharlesBrisco]

Not to lean verg of to much timing ported 4910s have no pull if there lean they will fall right on there face

[@Doc-Cole_Trickle-of-Chainsaws]

👍🆙CB

[@Witschor]

Why is that stock one so rich ? It fourstrokes the hole cut. Could you not adjust ist leaner?

[@CharlesBrisco]

It's still 100 %stock with limiters still in

[@Woodman_Custom_Sawing]

You can lean it out as far as the limiter caps allow and it still runs like that. It might clear up a little but it's in and out of 4 stroking.

[@Witschor]

@@Woodman_Custom_Sawing and that should be in the epa range 😂

[@Woodman_Custom_Sawing]

@@Witschor it's super annoying. I did a small muffler mod and leaned out the carb and it's still hard to get it to clean up in the cut. I haven't taken the time to defeat the limiters on the carb. Thinking about sending it to Charles.

[@tantonrosencranz2718]

Night and day difference

[@jeffshannon4096]

Wow

[@jeffshannon4096]

Is your porting available and if so how much? Same saw

[@forrestebert5276]

Hell I just bought a new in the box one for $250 with an 18” bar ! I’ve tried to get you to port it for me but no reply for some reason?? So I guess you only port fellow You Tubers saws and that is your choice too bad though!

[@CharlesBrisco]

I sure I sent a message back to.u

[@forrestebert5276]

@@CharlesBrisco You did but it was to go to someone else to do the porting. That’s not what I asked you to port mine for me. I’m not knocking you or belittling you it’s your choice and I respect you for that plus I have a line on more new ones but I’ll keep that source to myself. Plus I contacted you before about a 4310 and your reply was the same so I don’t know what to say but your work is Great and I wanted to experience it myself but I have others that will and so that’s where I’m headed to Charles.

[@CharlesBrisco]

@@forrestebert5276 I only port here an there an my messages get pushed down fast easy to loose track of were what was messaged to who an were

[@forrestebert5276]

@@CharlesBrisco No problem maybe I’ll meet you at saw fest in October

[@ricksanchez7459]

They ain't much stock, and you have them figured out, so its a huge, comical gap.

[@slaxxx]

L stock saws