String trimmer pull cord repair

[@SHONEY21Z]

Link to full video of step by step. kzbin.info/www/bejne/pKaQfX2qacl0odE

[@cotamanninetynine]

This video is so chopped up its useless. The guy skipps over IMPORTANT issues that a person trying to fix his trimmer would need to know. The MAIN ISSUE is the way Craftsman designed the pull starter. The entire starter assembly is made of PLASTIC. There is a lone steel retainer washer that is tasked with keeping everything together. My retainer worked its way up the shaft and allowed the spring arm to escape its retainer hole in the housing. Once that happens, the spring unwinds itself and the pull cord just falls out. Any good mechanic can figure it out. I am using a small amount of EPOXY to hold my retainer lock in place.

[@SHONEY21Z]

kzbin.info/www/bejne/Z5eulZywlN5njJo Agreed. Terrible design. And good idea with the epoxy!

[@edwardjenner1381]

THIS. If you just put the retainer back, it will likely just come off again. I think at the very least you would need a new retainer - these are single use. I was thinking about how to fix this. Would rather not epoxy, but may go that route.

[@SHONEY21Z]

@@edwardjenner1381if you bend the tabs down a little, they should hold. Try tapping lightly on the plastic the retainer sits on to flatten it a little, that should help hold the retainer in place

[@SagaSix]

I came here to say the same thing like wtf was the point of this

[@SHONEY21Z]

@@SagaSix did you check the link to the full step by step version? kzbin.info/www/bejne/Z5eulZywlN5njJosi=kKKz9OFZT0Yy5cak

[@davidkish1251]

You cut out a lot of good information like is clutch screw reverse thread or standard and a lot of teardown information not shown.

[@SHONEY21Z]

That’s my fault. Thought I hit record while song that and actually hit stop recording. Recorded my lunch instead. I will likely get another one in with the same issue and I’ll make a better quality video. Sorry for the mishap.

[@deejay8564]

I agree with you @davidkish1251. All the information I needed to know, he skipped it or remove it from the video. So instead of helping other people, it becomes harder to understand what this man was saying in his video.

[@SHONEY21Z]

Agreed. I on remaking this video as soon as I can. Thanks for the feedback 👍

[@SHONEY21Z]

It’s hard to hear and I didn’t do a good job explaining but If you shove some rope or pull cord down the spark plug hole and fill up the cylinder space with rope, the piston can’t turn over and locks the motor in place. Then you can turn the torx screw and remove the clutch bell housing.

[@E85_STI]

Yeah sucks because I have this trimmer but I took it all apart but the video is just not detailed enough to help so just look around there are other videos. I pretty much figured it out in my own the video is sort of helpful but I’m order to remove the clutch screw you have to remove the spark plug, put some string into the hole and fill it kinda so when the piston travels up it locks in place so you can remove the screw. It’s a normal lefty loosey screw.

[@FJBsaidcornpop]

What caused it? And is it not just going to do it again? Has to be a reason why it malfunctioned. Good video anyways. Thanks!

[@SHONEY21Z]

It could happen again. That lock washer should stay on but it’s a dumb design. If it happened again I would probably get a new lock washer or maybe melt a little of the plastic so it has a lip and won’t pop off.

[@FJBsaidcornpop]

@SHONEY21Z I've got a Craftsman WS210 pole saw that has been used twice that did the same thing the other day and I haven't had a chance to fix it. I think I'm going to fix it and sell it or give it away to somebody in the family and get me a Stihl.

[@SHONEY21Z]

@@FJBsaidcornpopthat’s probably a good idea.

[@dennyhall4466]

I’m putting the pull string back in at video minute 2:02 putting it back in which way does rest of rope go around it? It would help me so much thanks. Otherwise your steps have helped me the entire way thanks

[@SHONEY21Z]

Once the pulley is in, with the string fully pulled out, you need to grab the string from the pulley side, between the pulley and the plastic housing, an pull enough of the loop inward so you can wind the spring. Hook the rope into the little notch on the pulley and rotate clockwise about 5 turns (depending on how long the rope is). Then hold the pulley in place, it’ll now have tension, and make sure the rope is fully pulled out and slow the pulley to unwind, which will pull the rope back in.

[@SusanVernon-us5uh]

Yes can you tell me what way does the pull cord wind up what direction

[@SHONEY21Z]

kzbin.info/www/bejne/pKaQfX2qacl0odE If you didn’t fix it already, this video has more detail. If I remember correctly it’s counterclockwise but I’m not 100% positive.

[@rooseveltroberts2743]

This video doesn't show how to recoil the spring.. Not a very help video🤨

[@SHONEY21Z]

Apologies, camera man error. Didn’t realize til almost done. I’ll make a new one when I get another opportunity

[@morganbaxter8793]

Probably a long shot you see this but the T15 you use at mark :33. I can’t for the life of me get that screw out. Just keeps spinning. Any tips?

[@SHONEY21Z]

Is the screw spinning or is the motor spinning?

[@morganbaxter8793]

@@SHONEY21Z just spinning

[@SHONEY21Z]

Are you sure it’s a T15? Some ppl say their trimmer had a Phillips screws. If it is torx, are you sure the screw isn’t stripped? If it’s unscrewed but never came out, that’s because the screw is built into the clutch drum and you just need to pull it off. And finally, make sure you have something blocking the piston or the piston will just go up and down as you turn the screw

[@RobertPelton-ki1jg]

No if you are mechanically inclined it’s not chopped up. Ty

[@SHONEY21Z]

Check the linked video for a more in depth video

[@Lupz-uo1oi]

when i install the pull string everything is good until the point that i close everything up and connect the handle. The pull string is hard to pull. any idea why?

[@SHONEY21Z]

Something is hanging up. Is the spring in correctly? Is the road too big/long? Is the retaining washer on and in the right place? Did the inner white recoil sit into the larger one correctly? If all of that is fine, then it could be something with the clutch. Maybe you missed a washer or something. Check the longer version of this repair in the description, there’s more detail

[@Lupz-uo1oi]

I will double check. Thank you!@@SHONEY21Z

[@SHONEY21Z]

@@Lupz-uo1oi np. Good luck 👍

[@stevenberryhill3161]

My T15 screw is turning but that silver piece won't come off. What's up with that?

[@SHONEY21Z]

Did you block the piston from turning?

[@SHONEY21Z]

Also, there’s a link to a video in this video description that has a more detailed step by step version of this repair. That may help explain things better

[@Andrea_loves_makeup]

Do you have to use the T handle T15 like you have or can you just use any T15? Thank you.

[@cotamanninetynine]

Long handle T-15 Torx MUST be used.

[@Andrea_loves_makeup]

@@cotamanninetynine ok thank you!

[@SHONEY21Z]

Long neck T15 torx. 6” to be safe

[@dgjunior68]

Rope in cylinder trick. But rope is stuck. What can I do ?

[@SHONEY21Z]

Rock the piston back and forth while pulling. If that doesn’t work, probably have to pull the exhaust off. The rope is likely pinched between the piston/cylinder and sticking out the exhaust port. Appended once or twice to me. Gently force in the right direction usually pushes the piston down enough to free the rope.

[@dgjunior68]

@@SHONEY21Z how do I rock the piston back and forth. Through the spark plug hole ?

[@SHONEY21Z]

@@dgjunior68is the clutch still attached? If so, use a wrench on the clutch to move the crank back and forth. By pulling the back cover off, you can see the crankshaft and see what direction you would need to go to get the piston to move away from the spark plug hole.

[@dgjunior68]

@@SHONEY21Z YES it is. i had tried that turning it both ways but it is really t in there tight. pull chord won't move either. I will try again tomorrow. thank you.

[@SHONEY21Z]

Let me know how you make out

[@llsquared7394]

HELP! I'm stuck at the step (second 58) When I turn it it just keeps turning and turning and never unthreads, just keeps spinning to the left. Which is the direction the arrow OFF points. Any suggestions?

[@llsquared7394]

Ok I just watched your more detailed video and see what to do now. Thank you!!!

[@SHONEY21Z]

@@llsquared7394glad I could help. Thanks for watching!

[@dykesicle]

You got a part number to replace the whole coil?

[@SHONEY21Z]

Have to check your model because it’s the same principle but different models depending on the make and model. This is basically what you’re looking for. MTD 753-09224

[@silversurferhdz]

All did all the steps, now when I pull it makes scraping noise...help..

[@SHONEY21Z]

kzbin.info/www/bejne/pKaQfX2qacl0odEsi=UpWK242h2lIGxF0L did you watch this vid for all the steps? My guess is maybe put a washer in wrong sport or not at all. Might have to pull it apart again and see if there’s any scratches where it’s dragging and see if every hint was put together right

[@BeatMoneyAD]

When I use the t15 to remove the screw, it doesn’t loosen. It keeps spinning the pull string inside. What am I doing wrong? I have the WC2200

[@SHONEY21Z]

Did you put a string in the cylinder to block the piston from moving?

[@BeatMoneyAD]

@@SHONEY21Z Yes. I got it out.

[@SHONEY21Z]

👍

[@dennyhall4466]

At 2:02 do you wrap the rest of the cord around it or does it hang at the bottom inside?

[@SHONEY21Z]

kzbin.info/www/bejne/pKaQfX2qacl0odE Have you watched this video? Start at 16 minute mark

[@dildarhussain6594]

Cz i buy but this white pully with rope was missing , so i dont know what part nmbr is for pully or from i can buy. Thnks if u let me know

[@SHONEY21Z]

Sorry I can’t help you there. Take a look at the parts diagram and search for a part number.

[@jagrench62]

I discovered that the crank cover can be removed then you have two holes in your counterweight in the crank put piston rod in between both of those holes and then put a torx with a handle on one or both sides of the connecting rod and it will hold it in place while you loosen everything.

[@SHONEY21Z]

That’s a good idea. I’ll have to try that next time. Thanks!

[@jacksonshermna9277]

Very helpful man just needed a Quick Look to make sure I was on the right track. It’s a stupid design in my opinion pull cords always break so it should be one the easiest parts to access

[@SHONEY21Z]

You would think so haha. But they made it so ridiculously tedious to replace and repair.

[@lparzl3295]

at 0:25, theres that metal “piece” that i am trying to get out. you mention you use a T15 but i cannot find a T15 that has a skinny enough shaft to go down and unscrew the metallic “piece” off. can you possibly tell me exactly what tool you bought?

[@lparzl3295]

@@SHONEY21Z thank you so much

[@cotamanninetynine]

T15 long handle NUST BE USED!

[@SHONEY21Z]

Np

[@SHONEY21Z]

Exactly! Thanks for the reply

[@Charm-313]

For anyone that could help. If I just removed the whole pull cord and just used electric start, would that work?

[@SHONEY21Z]

Yes it should still work. If the rope is just pulled all the way out, you could just cut the rope and not have to take it apart and remove it

[@Charm-313]

@@SHONEY21Z thanks for that 😁👍🏾 Just saved me money on a new one😉👉🏾

[@jordanmathis5744]

What kind of tool was that t handle

[@SHONEY21Z]

It’s a T15 torx T handle

[@dukedowg]

What size is the T15 torx handle ?

[@SHONEY21Z]

@@dukedowg T15. It’s about 6” long

[@tonypagan8852]

What's would charge someone for that job?

[@SHONEY21Z]

On a model like this, probably 3/4 of an hour to an hour. Whatever you think your time is worth

[@hicoteo]

Over a day of use everything that can break broke on my Truper including the shoulder strap. I hate these things. 😡

[@SHONEY21Z]

Definitely not built like they used to be

[@hicoteo]

@@SHONEY21Z Well, to be honest mine has been sitting for about a year without proper maintenance. 🫤☺️

[@SHONEY21Z]

It’s worse for them to sit

[@richardreid8908]

Great video video but at 3.58, the clutch still turns! There has to be a way to stop the whole thing turning?

[@SHONEY21Z]

You lost me. The whole video is 3:58. Are you talking about the clutch drum or the clutch itself? Follow the link in the description to a long version video that will go through step by step to stop the clutch from the turning to loosen or tighten the clutch.

[@robh.7699]

WoW!!! Never showed how to do the rewind of the spring.....

[@SHONEY21Z]

Check the video in the description. It’s a full length video. Also, winding a spring is extremely Difficult. Even for professionals. Usually they have a special tool.

[@scottouimet2865]

Ty I couldn't for the life of me.figure out how to take that shaft off the end

[@SHONEY21Z]

Glad I could help

[@scottouimet2865]

Got the torc driver and the motor wouldnt stop spinning. But I found the info in another comment of yours!

[@NastyOuTCasT]

so I'm not understanding how the cord in the piston helped! i tried, it did absolutely nothing!

[@SHONEY21Z]

Your piston keeps turning over? If you put enough rope into the cylinder, it’ll block the piston from going up and down. Then you can remove the clutch

[@NastyOuTCasT]

@@SHONEY21Z that was a quick response! yea i got scared to feed to much of it in. i wound up just using a slim rachet to push down the piston and smacked the metal off piece with a mallet lol!

[@SHONEY21Z]

Whatever works haha

[@IHC1965]

This video is not usefull. Doesnt give the most important steps to remove the cordreel

[@SHONEY21Z]

Sorry. Thought I had it recorded but it wasn’t recording. Also, in this particular trimmer, the lock washer fell off and that’s why the cord wouldn’t retract, so there wouldn’t have been a video of how to remove the pull cord assembly. I can talk you through it if you need help.

[@jagrench62]

how do you hold the crankshaft so you can turn off the centrifugal clutch

[@jagrench62]

got it thanks, rope in the cylinder . I have used that trick on German engines to replace the valve adjustment pucks. thanks.

[@SHONEY21Z]

Yup. There is a special tool for that but the rope in the cylinder is free and works just as good.

[@TheGenerationX894]

@@SHONEY21Z how do you put a rope in the cylinder

[@SHONEY21Z]

@@TheGenerationX894 I usually use pull cord rope and feed it in with one hand and push it through the spark plug hole with a flathead screwdriver. Just be careful to not mess up the plug hole threads.

[@TimmyBillingsley-lz5yn]

Stick a screwdrivers ver hold clutch works also

[@Andrea_loves_makeup]

How do u get the big silver piece off? My boyfriend used a regular T15 tool but not the T handle like you have. He thinks it’s stripped out and which way do u turn it to remove it? thanks

[@SHONEY21Z]

Did he block the piston from moving with a rope down the spark plug hole? Otherwise he’s Just going to turn the motor over. And the T15 needs to have a long enough neck to reach the bolt.

[@Andrea_loves_makeup]

@@SHONEY21Z yes he tried that he said the bolt inside to get the it off is stripped out it’s reaching the bolt but not turning to remove it because the person that had the weed eater before him must have stripped it out. Do you know if there is any other way to remove it? Thank you for replying back.

[@SHONEY21Z]

@@Andrea_loves_makeupis he able to see down the hole with a flashlight? Make sure someone didn’t replace the bolt with something other than a torx. If it is a torx and it is stripped it’s going to be tricky. There are ez out bits but the opening is so narrow it’s be hard to get an extension down. The other thing would be a small flathead screwdriver, smaller than a t15 torx bolt, hammer it down into the grove that’s stripped and try turning it. Might need a vice grip on the side of the screwdriver.

[@watcherwatchmen7785]

Designer intentionally made it difficult to replace the pull cord so that people would give up and buy another. It would have been easy to mount the pull cord on the rear.

[@SHONEY21Z]

Exactly. They did this so they could put the electric starter access in the back. But nobody ever uses it anyway. Should just put the pull start back to the back again with 4 bolts holding it on.

[@dildarhussain6594]

Can u let me know where this white pully which is under the rope.

[@SHONEY21Z]

I’m not sure what you mean. Is there a part missing in your edger?

[@estevanperez3923]

How do I get silver top off

[@estevanperez3923]

Just keeps spinning

[@SHONEY21Z]

Are you talking about the on piece that hold the pull cord on or the clutch that goes to the shaft? If it’s the clutch, you need to put a rope in the cylinder to keep the motor from spinning over. I used a Chanel lock to hold the clutch while using an adjustable wrench to turn the nut. It’s tight but it’ll come off.

[@SHONEY21Z]

If you are talking about the clutch adapter, that’s when you use the rope in the cylinder and then use a torx wrench to go inside the tube and remove the bolt.

[@pineapple0310]

But how did you take off the top? I keep trying and it just turns. All videos I've seen just show once they are just pulling it off, not how to take it off. One video just showed the guy pushing down and it just came right off 🧐

[@SHONEY21Z]

What do you mean by the top? Are you talking about the bolt that’s on the clutch? If so, you have to put a rope down the spark plug hole to block the piston from turning over. If you’re talking about the nut on the clutch, you have to clamp something on the clutch drum while you turn the nut.

[@1netaz]

When he says stabilize he doesn't clarify that he means stop the engine from turning when you turn in the nut the engine turns with it so you got to stop the engine from turning

[@Andrea_loves_makeup]

Hi i have a question my boyfriends T15 bolt is stripped is there any other way he could get it off? i have a T15 tool but it’s a regular T15 not with the T handle like yours. Thank you.

[@SHONEY21Z]

Correct. Thanks for clarifying. There’s a full length video now in the description that goes into more detail.

[@epeiusgarage]

This must have skipped so much. Stabilize it while removing the clutch? How? It just spins.

[@SHONEY21Z]

Have to put a rope down the spark plug hole to block the piston from turning over. I stated it earlier in the video but didn’t explain it well enough.

[@SHONEY21Z]

kzbin.info/www/bejne/pKaQfX2qacl0odE

[@dildarhussain6594]

I hv wc210 craftsman weed eater trimer

[@SHONEY21Z]

👍

[@reyjc69]

Need to keep the camera focused on the part being fixed!

[@SHONEY21Z]

Definitely! Spielberg wouldn’t be happy with the directing of this video.

[@josephercolano1029]

My spring popped off like you said was probably the issue. Put everything back together and it doesn’t seem to go all the way back in still. Usually a few inches of rope still left to retract. It’s not exactly the same every pull. Any thoughts?

[@SHONEY21Z]

The spring wasn’t wound enough times. I usually turn it about 4-5 times. If it’s only 3 or less, it won’t recoil enough to pull all the string back in.

[@josephercolano1029]

@@SHONEY21Z Ah okay that makes sense. I didnt turn the spring at all I just extended it from where it was resting to that slot. Ill have to take it apart and spin it in around like you said. Thank you!

[@SHONEY21Z]

Hope it worked out!

[@RandyCandelario-gq6kt]

Why make a video and not show the entire process?

[@SHONEY21Z]

Watch the video in the descriptor pinned at the top of the comments. Thanks

[@bxhhddby2191]

Cool looks like I'm buying a new one lol

[@SHONEY21Z]

Haha. It is possible to fix. Check the longer version video on the description, shows step by step instructions on how to repair.

[@josepagan8318]

Thanks 🎉

[@SHONEY21Z]

No problem

[@totallygrim1]

lol buddy a few good points but you gotta redo this lol. Full tear down with no edits. You can correct yourself in the video or description. This should be like 15 minutes or more. All the complicated bits aren’t here. The coiled spring, making the rope taut, blocking the engine fan or however to turn the screw with the t15. Rly appreciate the effort though, just trying to be constructive 👍🏼

[@SHONEY21Z]

Thanks for commenting! And you’re absolutely correct. Check the pinned comment or the video description for a full step by step version of this video. Cheers!

[@misticphillips647]

You missed a couple steps

[@SHONEY21Z]

String trimmer pull cord repair kzbin.info/www/bejne/pKaQfX2qacl0odE

[@Osgood-e4m]

why are you not using a stand for your phone? This video is so misleading I cant believe I suffered through it.

[@SHONEY21Z]

String trimmer pull cord repair kzbin.info/www/bejne/pKaQfX2qacl0odE Did you see the link in the description to the step by step video?

[@danny-hh2gc]

I like your video bro, but i wish you were little bit slower on the explination

[@SHONEY21Z]

@danny-hh2gc sorry about the poor video quality. Maybe this video will help you, I break it down step by step. Thank for watching! kzbin.info/www/bejne/pKaQfX2qacl0odE

[@joshhuckleby4414]

Nope I’ll just buy a new one my cord just snapped and my back up weed eater the piston keeps slamming the gap on my spark plug I’ll spend the 120 to 150 for a new one

[@SHONEY21Z]

😂

[@marshallcollins3376]

Time for a tripod

[@SHONEY21Z]

Done!

[@joshuaakers5291]

How the hell do you take off the goddamn washer??? That would have been good information to have!!!

[@SHONEY21Z]

@joshuaakers5291 kzbin.info/www/bejne/pKaQfX2qacl0odE This will show you full step by step process. Thanks for commenting! Hope this helps!

[@terrellscaife2411]

Thank you help me out a lot you’re awesome

[@SHONEY21Z]

No problem glad I could help. Not the best video but I think it gets the point across.

[@petersack5074]

Krapsman, ...er craftersjunk,,,,,,no.....craftsman, is just another name, for plastic ' junk '.

[@2MasterBuilder2]

I try to buy American when possible and I have this trimmer. Well, yesterday, I went to start it and the rope slipped through the pull handle (the knot came loose). Now I have to disassemble it to fix. Terrible design and the trimmer is only 1 month old.

[@SHONEY21Z]

Have you pulled it apart yet? Did the metal retaining push nut come off the shaft like this one?

[@randalcquebedeaux314]

They all are crap. Mine never last more than a year. Love the attachments and only a few are jump start capable. Many different names, but same manufacturer.

[@SHONEY21Z]

It’s getting worse. The stuff I get in now is very cheaply made.

[@mikeoburn718]

I hate mine garbage weedeater and I love craftsman.

[@SHONEY21Z]

I have to agree. I normally don’t mess with trimmers besides echo and stihl.

[@ЯрославаБогдан-я3ь]

I had a model older than this one that I love. My sister has difficulty with tools that are too heavy and she actually loved mine and found it easy to use kzbin.infoUgkx_rBCFuDW1zD6blTGhLkvAkxU657uR_lG . This is a newer model but was even lighter which she really appreciates. She enjoys it and I no longer have to go to her house to trim as she can handle it fine. Haven't used it enough to comment on the battery life but lithium batteries last longer than the old style. Being cordless makes it easy to trim the far edges of the property. The entire yard can be trimmed with one charged battery.

[@SHONEY21Z]

Thanks for watching!

[@Kelvinllovejr]

Jesus. I have the one on the side which should be easier but you can't tell me it's this damn complicated! Ridiculous

[@SHONEY21Z]

Idk who designed this but they were definitely not thinking of anyone else

[@Kelvinllovejr]

@SHONEY21Z I'm going to call the help number and maybe it will work.

[@SHONEY21Z]

What are you having trouble with

[@Kelvinllovejr]

@SHONEY21Z the pull string won't recoil. Once I put the cover back on I pull it once and the cord stays out at full length. I have to take it off again and coil it back up to start over. Everything else is perfect. I only bought it last year so everything is new. I watched a video where the guy was saying it needs to be lined up but I'm not sure how

[@andyczech6993]

I also run into trouble recording each individual step when making videos. Sometimes there’s a lot to cover and you just really want to get the project done with. It takes skill to produce videos and fix stuff simultaneously, on your own. Overall, not a bad video. Certain information was helpful - I would have spent hours trying to pry the clutch cover off without knowing about the T15-head bolt. 😂

[@SHONEY21Z]

Thanks for the reply, this is by far my lower quality video and I plan on remaking it as soon as possible. Glad I was able to help you and some others.

[@andyczech6993]

For the record, a 1 7/8 socket and a breaker bar pop that clutch off nice.

[@the90sinfluence]

Same here, I got that far and searched for a video

[@SHONEY21Z]

That’s good advice l. Never thought of that!

[@terry5452]

I gave you a thumbs up on your advice but that Craftsman still a piece of crap

[@SHONEY21Z]

lol yup

[@Itzalwys1420]

Craftsman shit is just like a Ford!!!! Gotta take every damn thing off for a simple repair

[@SHONEY21Z]

Terrible design

[@Ekimbrown]

Very poorly done video and not done in a step by step fashion. Camera in too close all of the time. Cant really use this vid for start to finish operation.

[@SHONEY21Z]

kzbin.info/www/bejne/pKaQfX2qacl0odE

[@mountainplumbing]

China Men hope no one will repair it.

[@SHONEY21Z]

Haha basically

[@JackieHarding-u7y]

Very poor video you left out too much important information and I'm sure you could do better than that

[@SHONEY21Z]

Did you look at the description? I made another video more in depth. Thanks for watching!

[@gerry_904]

You skipped every necessary step.

[@SHONEY21Z]

kzbin.info/www/bejne/pKaQfX2qacl0odE

[@claybird8970]

Please don’t make any more tutorials geez

[@SHONEY21Z]

Hahaha 😂 thanks. Check out the link in the description or the pinned comment, there’s a link to a full in depth video. Thanks for commenting!

[@richducko9753]

yea video really sucks didn’t show nothing won’t watch him and sin

[@SHONEY21Z]

Did you read the description? Here is a link to a step by step tutorial. Thanks for commenting though. String trimmer pull cord repair kzbin.info/www/bejne/pKaQfX2qacl0odE

[@korbinevans5588]

You skipped so many steps

[@SHONEY21Z]

kzbin.info/www/bejne/pKaQfX2qacl0odE

[@cotamanninetynine]

Terrible Video....

[@SHONEY21Z]

No argument here. I plan on remaking this video asap.

[@SHONEY21Z]

kzbin.info/www/bejne/pKaQfX2qacl0odE

[@DavisEsand-yp7my]

This kind of machine is trash don't buying..😢

[@SHONEY21Z]

Can’t argue with that

[@darrenpritchett1516]

Your not good at explaining this procedure 😊

[@SHONEY21Z]

Did you watch the other video in the description?

[@YDDIRP]

almost helpful

[@SHONEY21Z]

I remade it. Watch here String trimmer pull cord repair kzbin.info/www/bejne/pKaQfX2qacl0odE

[@roscodrummer]

Video is useless h poor instructiom

[@SHONEY21Z]

Check out the linked video, it is much more in depth. You’ll find it much more useful