OpenTX: D8 bind with internal or external Multi protocol module

[@HaveFaithInGod]

Good job. I followed your lead leaning often on the "pause" and backing up to get things right. I bound my first model on this Jumper T-Lite usiing your guidance. Thanks. I'm not a total nube as I do have a Jumper T8SG Plus but I know nothing about Open TX, only have used Deviation system until now. I connected my Tiny Hawk II. I will make separate models for the Tiny Hawk I and the "S" model so I can fine tune the frequency of each. Thanks again.

[@stylesuxx]

Happy I could help you :-)

[@matred3538]

Thank you so much, was having trouble getting my switches to work. All sorted now. Many thanks.

[@stylesuxx]

Cool, happy I could help.

[@zico3239]

Mine is on the way when i start using it these short usefull videos would be a life saver keep on with the good job 👍

[@stylesuxx]

Thanks - I have a couple more planned - they are in my back log for quite some time, a new radio was obviously the motivation I needed to get them done. And let me know if you run into any issues. I am pretty sure you will love this radio.

[@zico3239]

@@stylesuxx thanks alot. wont miss a video i guess very kind of you 👍👍👍👍

[@zico3239]

@@stylesuxx i am a begginer it is good to have a small radio than a big one

[@stylesuxx]

@@zico3239 I really think it is personal taste. I can't handle the big boxy ones - I use my thumbs for flying, so the gamepad shaped ones are perfect for me. When I first started out, I modified a Joystick as a controller, but that was a pain to carry around... I highly recommend finding other people in your region that also fly and then simply swap around gear. That is a great way to try different things and see what you really like.

[@benlamb1870]

Cheers, my switches now work, I don’t full understand but they’re working👍👍

[@jferreira879]

I'm trying to bind tlite to frsky r xsr and have already flashed the rx to older accst fw. When I go to bind the beeping on tlite stops, making me thinks it is bound but the rx lites don't change and betaflight doesn't show it is bound ( no mvmt of anything). I then try to rebind, tlite goes into bind for 3 beeps and stops, exiting bind mode on its own. It does give warning when I boot tlite about no failsafe setup, making me think it is bound, but nothing else. Any ideas? I want to frequency tune but can't til I can see rssi.

[@Mr_Furey]

Did you find a fix?

[@jferreira879]

@@Mr_Furey yes. I had to do freq tuning. Once I changed that even a little, then the Rx also acted bound and I was able to arm and fly. Makes sense because the jumper is a 3rd party to frsky so doesn't have inside info on exact frequency.

[@zico3239]

very helpful a real short cut

[@kunad2294]

hello how do you bind omphobby m1 helicopter and also eachine e160 to jumper t lite would love to know .

[@stylesuxx]

I don't have any of those models, but you would need to find out which protocol they are using, then set the transmitter to this protocol and bind them up.

[@MrSupergumpi]

Super video! How do you clonerx with the t-lite?

[@stylesuxx]

You mean cloning the TX to which a model is already bound to? I have not yet looked into that to be honest.

[@MrSupergumpi]

@@stylesuxx yes, I have played with it on my t-lite without success. BTW really informative videos, great work

[@stylesuxx]

@@MrSupergumpi That feature actually really sounds interesting - I will give it a try and see if I can come up with something.

[@Vosper385]

Hi Stylesuxx, Many thanks for this video, I got my T-Lite a while and have been trying to bind with some models with FRSKY NON-EU RX's however I am not having any luck, I wonder if you might be aware of any other tips and tricks I should be doing to get them to bind? Thanking you, Mark.

[@stylesuxx]

Well, it depends which receivers you are trying to bind to. If you have new receivers that already use the access protocol it will not work and you will have flash an older firmware version to those receivers.

[@Vosper385]

@@stylesuxx Many thanks for your reply, I have the older RX's which I purchased around the time of my original Taranis X9D, ACCST I think they all are. I have some D4RII, D6FR and another which I cannot recall the specs on but they are all at least 5/6 years old but in perfect working order.

[@stylesuxx]

@@Vosper385 Well, they should all work in D8 or D16 mode then. I recommend first putting the receiver in bind mode and then the transmitter.

[@Vosper385]

@@stylesuxx Thanks again, I'll try again.

[@Mr_Furey]

We're you able to bind?

[@itsmelouisfun]

Is the swa switch a 3-point switch? Even if you move swa in the input setting, only values of 100 and 0 are shown like 2 points.Check please

[@stylesuxx]

Yes, swa is a three position switch.

[@lincolnmcdowall3801]

How do you set failsafe?

[@stylesuxx]

It depends. I only fly quads, so fail-safe is basically handled by Betaflight - if the receiver signal is gone, it will default to disarmed and will set the controls to default state. Unless you configure something different or have GPS. The test that I usually do, is connect the copter to the betaflight configurator, turn off the radio and see what happens, if throttle goes to 0, I know the quad will just drop out of the sky. If you do not use a flight controller, it depends on the receiver which options you have for failsafe and you should consult the manual of your receiver.

[@JoeL-vf6lc]

how do you delete inputs? i set the wrong input to ch5 and when i went back in to change it, it added another ch5 input. kept messing around with it and now i have 4 ch5 inputs showing in the list.

[@stylesuxx]

Select the input, long press enter, then from the menu select "delete".

[@romyou7683]

Hello, I bought the same device you have with the r900 signal receiver, but I found it difficult to connect the connection between them

[@stylesuxx]

r900? You mean Jumper R 900?

[@romyou7683]

Yeah

[@stylesuxx]

@@romyou7683 ok, so you are using an R9 Module? Maybe tell me which part is giving you a hard time...

[@romyou7683]

@@stylesuxx I want to connect them

[@stylesuxx]

@@romyou7683 so which R9 TX Module do you have exactly? And do you have it set up on the radio yet? Can you bind to other R9 RX modules, or is the R900 the only one you are having problems with? You need to give me more information about the hardware you use a d what you have tried to get it working, otherwise I can not really help you...

[@vikingotubez]

You don’t need to search for the switch, just actívate it and will be selected, cheers!

[@stylesuxx]

Yes, you are absolutely right, thanks!

[@mrmirech4795]

I ordered one too👍

[@omerbahtiyar86]

I’ve bounded up with my UMX Timber, everything is fine and works. Now I would like to fine tune the frequency but I don’t hve the option I see in your screen. How is that possible? Firmware version: Factory (84c86f71)

[@stylesuxx]

That is very strange - you are running a D8 receiver, right?

[@omerbahtiyar86]

No it’s a Spektrum receiver

[@stylesuxx]

@@omerbahtiyar86 ah, yes - from what I have seen Frsky are the only ones with this fine tune setting.

[@kunad2294]

thanks , my question should have been not how to bind helicopters, but the switches for throttle hold and idle up 3d switches dual rates .

[@stylesuxx]

Sorry, I only fly quadcopters, I can't really help you out here...

[@kunad2294]

@@stylesuxx ok peace.

[@ianmontefpv]

Very helpful

[@oscarsolbakk6442]

I got it binded to my freestyle 2 but it wont arm... What do i do?

[@stylesuxx]

Well, did you set up the modes in beta flight?

[@antzrrf]

For mobula7 ?

[@stylesuxx]

Not sure what you want to know? If your Mobula7 has an FrSky SPI Receiver, the it is the same way.

[@Vosper385]

Hi @UC6-jd4jlhnGFQEPjNxM8RMA, Many thanks for this video, I got my T-Lite a while and have been trying to bind with some models with FRSKY NON-EU RX's however I am not having any luck, I wonder if you might be aware of any other tips and tricks I should be doing to get them to bind? Thanking you, Mark.