Super ATV Quadbike - Homemade Four Wheeler Project

[@charlesroman9163]

You have really grown over the last couple of years. It has been enjoyable watching your progression. I would love to ride some of your creations. Keep it up!

[@oficio_e_artificios]

Ficou muito legal o projeto. Parabéns

[@ewanbaxter9199]

Looks good. Didn't see what the extending frame at the back was for, you mounted the brake light on it, what does it do. Never use threaded rod as a pivot, it only makes contact on the sharp, knife point peaks, it has to be smooth rod, preferable able to grease it too.

[@luizantonio755]

Bom dia amigo Q, lindo mesmo este quadriciclo gostei é show demais

[@taters-no4gj]

Next time you build something like this, may I suggest you use bearings on the suspension arms. The threaded rods you used will wear down surprisingly quickly, particularly as they're a stressed member. Looks like a fun piece of kit 😉👍🏻

[@vikasvishwakarma6033]

😅😅😅oooo😅😅😅😅😅😅😅😅😅😅😅😅😅😅😅😅😅

[@areindra3698]

😊 23:34

[@diyathomevn]

Thank! ❤ Your video came just in time for me to get this bike! I love it! very good car ! I wonder if the super cool EC4P motor kit can be installed on this bike, but I plan to create a full-blown ebike that can reach 4.0 for example! Thank you!😉👍🏻

[@WattDuWolle]

I love my Raptor 700, but this is a good job 4 noobs, big hand all of y, bb from germany

[@juanjoselopezpaniagua5969]

Gracias amigo nunca lo olvidaré y su sabiduría son muy pocos las personas como usted gracias Nuevamente su seguídor y Amigo Juan Jose lopez

[@bobboboff5326]

К сожалению, таких наоборот много 👎

[@silverxiree]

front wheels have severe negative camber. Thus while you are driving in a straight line or accelerating give extra attention to the vehicle because it could be extremely unstable. And also, since this vehicle is an off-road vehicle, having a positive camber angle will provide a more comfortable steering control.

[@CHERALAUTO]

thank you for your advice ... I agree there are some adjustments to make

[@gabrielalejandroverapinto1974]

I'm considering a project like this, please could you explain what negative and positive chamber is? And how to fix it?

[@doeverything7997]

@@gabrielalejandroverapinto1974 Do a search for "positive v negative camber" and look at a few images... with negative camber, the top of the tires tip in towards the centerline and the wheels are bowed out, and positive is the opposite. Several ways to address the issue, depending on where you are in the design/build/use cycle.

[@ВикторМеркулов-н6ч]

Руки прямо откуда надо растут и голова на месте 😉

[@bobboboff5326]

С какого? Чтобы сделать так очередную залипуху, много ума не надо 👆. Конструкция просто шлак!

[@massimilianozafaro1688]

Buono il lavoro e la tecnica per realizzarlo , sono daccordo nell'utilizzo dei cuscinetti dove metti le barre filettate , volevo dirti pero' che a me sembra che l'altezza da terra sia troppo poca se trovi un sasso o una cunetta tocchi sicuramente il fondo e poi secondo me la posizione di guida andrebbe raddrizzata si vede dal video che per quidare sei curvo e in fuoristrada non va benissimo....comunque ottimo lavoro provero' a farlo anche io....grazie

[@robertblackshear8963]

Good job and excellent welding. Stick welding is the strongest.

[@Adamchannel1993]

Wow keren sekali👍👍

[@TDK054]

Very nice!!! 👍👍👍

[@epicmaster9831]

e uno dei migliori veicoli mai creati e mai realizzati il prossimo video e al mcdrive

[@johnparrish9215]

This man has proven that the best skills to have are the Mental skills of planning and mathematics.

[@АлександрИгнатьев-ю5д]

But I didn't take into account one rule..the frame of any machine must be smooth and precise in its dimensions..since there will be an imbalance and vibration if they do not match ..and there will be a lot of shaking ...at high speeds.

[@dillanthomas-seiler9067]

You’ll hear the blokes wanna try on this, women on the other hand, they aren’t even interested is such beauty

[@pgravindran4273]

good working

[@josephdemarco1042]

Please tell me there are plans for this? I would love to build one.

[@rafaelvaldovinos491]

Muy buen trabajo amigo como quisiera yo hacer una asi

[@thundercats475]

amazing!

[@abhiyadidya6078]

Add some fog lights for next level look

[@noreddinehocine6774]

Super 👍👋

[@franciscowashington2155]

Beleza muito bom 👍👍👍😎😎

[@CHERALAUTO]

Obrigado pelo seu comentário! Fico feliz em saber que você gostou do meu trabalho. Se você tiver alguma sugestão ou ideia para futuros projetos, por favor, me avise. Obrigado novamente pelo seu apoio e por assistir ao meu vídeo.

[@everything-202]

Great👍👏

[@CHERALAUTO]

Thanks 😊

[@juanjoselopezpaniagua5969]

Amigo yo quisierá el pláno de De su máravilloso proyecto De su ermosa creácion Se lo agreseria el Resto De mi vida su seguídor Y Amigo que lo admira Muçho me dejó inpresonado De parte De su seguídor y Amigo Juan Joselopez

[@thebodean1964]

Great job friend, but my suggestion is to square everything up and to adjust your negative camber before you have an accident. Do you have a welding table and do you need a welding machine? Keep up the good work, God bless 🙏

[@erice.wallace4571]

Gorgeous! Lol!

[@florsilvestreentreoutras8294]

I like your job my friend❤ Sorry I don't speak inglês

[@donhelphenstine7597]

Excellent.

[@CHERALAUTO]

Many thanks!

[@emilianorodriguez5788]

Soy tu fan

[@prmarcos9083]

Ficou muito bom o projeto só faltou disponibilizar as medidas

[@sergioluizgarciafilho8311]

FABRICAÇÃO SHOW PARABÉNS TOP

[@АлексейПетров-з8о3ф]

💪👍Молодец, только дуга с переди лишняя🤨🤔. Ударишь, колесо потом не провернешь

[@user-yz86]

Супер спасибо большое за видео сразу видно руки растут откуда надо!

[@عاطفالود]

صراحه مبدع

[@markiller5689]

Hello, can I ask what engine you used for this project? Good job btw 👌

[@stefanradulovic3129]

Hi bro can you give us full video with measures.

[@gilankattera9143]

Can tell amount of tube used for construction

[@CHERALAUTO]

Thank you for your comment. For the construction of this particular project, we used approximately 15 meters of 30x30x2 mm tube. However, please note that the amount of tube required can vary depending on the design and size of the vehicle. I hope this information helps. If you have any further questions, please don't hesitate to ask

[@VasilyTerkin228]

​@@CHERALAUTOГде можно найти подробный чертёж?

[@Андрей-ш2э8л]

Долго ли проходит подвеска без сайлентблоков?

[@ME_ha_nik]

Хз

[@swalowit]

Nice Job !! How many CC ?

[@Василий-д8м9б]

Прекрасно все,но надо б повыше сделать ,а то колени достают до подбородка.

[@muntinu]

is it waterproof ? (rain)

[@fakename9024]

Can you install a Hyabusa engine?

[@techworksinfo]

Good work bro

[@pcfnokia273]

Phải thiết kế cái che mưa ☔ năng

[@MichaelZulu-y3r]

What type of engine do you use

[@sreejithtechpro9630]

Bro can you please tell me the total cost of this project❤?

[@CHERALAUTO]

About 1500$

[@FBPrepping]

Is something with a chassis made with square structural 1040 or 1060 steel suited for a vehicle? is even possible register something like this?

[@doeverything7997]

If you're looking to build something street legal, different countries and different jurisdictions will have different rules you have to abide by that may include minimum strength and stress requirements. A true answer I give you for my region may not apply to you, and so on - call whatever office in your region that licenses and registers vehicles for street use if that's what you're looking for. If you want to stay off-road on private property, those rules generally won't apply - but my advice is to always overbuild something for whatever you think you're going to need to do with it. Better to have it "too" strong than too weak.

[@glebmechanic3458]

От чего ступицы впереди поставил?

[@Игорьк-и3в]

кровь из глаз,от используемых материалов

[@oficio_e_artificios]

Top

[@XplorinWithPaul]

Aluminum or steel frame?

[@vostok417]

Super

[@999benhonda]

That rear sprocket is too small...and the muffler sits where it could get hit. Otherwise, looks like a solid build!

[@cemalbaskurt1249]

hi ! I have a question . I build trike bike from the 180 cc motorcyle but I didnt use differential cause of that . I cant turning easily . and ı watched your video you to dıdnt use differential but you turning easily can you explain this how ?

[@ManiacRacing]

Solid axle and big power makes it easier to break tires loose. Your drift trike has too much traction for the power you have. Try some harder tires or use drift sleeves. Honda ATC trikes had same issue. Riders learned to use body weight to lift the tire as needed for tight turns

[@cemalbaskurt1249]

@@ManiacRacing thank you so much bro

[@armandogutierrezcampos2167]

De dónde eres amigo como cuánto sale ASER una así ok muy guena y mas aguantadora ok

[@Hakan_Uyan]

Kaynak yapman ve işçiligin çok başarılı ama gözlerim kör oldu kaynak ışığından biz kanak yerini görelim yeterli

[@SomeRandomWittyName]

out of curiosity what was the estimate cost of the project?

[@rubengalindez6969]

can I get plan and measurement of the frame.

[@genikland1]

are there plans-drawings?

[@strawbob]

In all the video's I've watched, why does everyone hold the piece by hand when there drilling it? Health and safety, people you only get one pair of hands.

[@АнатолийПапенфот]

как ведёт себя задний мост - без обгонных муфт и дифференциала? - не ломает ли на асфальтовом покрытии дороги? - езда в режиме "блокировки" плохо кончается для резины покрышек...

[@glebmechanic3458]

Насчёт этого не знаю,но такая система много где применяется,на картинг лично ставил,без обгонных муфт и прочего,все хорошо

[@rendi6750]

We need exhaust racing🙏

[@Prathap3737]

Where is the clutch bro 🤔 but good work

[@enrico-q9v]

👍👍👍👍👍👍👍👍👍

[@edilsoncriadordeinvencoes]

Legal👍

[@Peort]

👍👍👍👍🔥

[@CHERALAUTO]

Thank you for the support, we appreciate it!

[@garagemslzv8465]

Tops

[@MahdiHasanloo-w8g]

❤

[@Malvandi_Electronic]

👏👏👏👏👏👏👏👏👏👏👏

[@ranieryrodrigues585]

👍👍👍👏👏👏👏🔧🔧

[@teleamcv2237]

Выложите размеры заготовок

[@florsilvestreentreoutras8294]

❤🎉

[@gabrielalejandroverapinto1974]

Hello, nice video, is there any way I could get the measurements of the chassis? I would like to attempt to do this myself

[@CHERALAUTO]

Visit www.cheralauto.com

[@kieles-fs9oe]

How much cost of that project?

[@ЗлойДядька-ц3я]

Если бы и размеры, то вообще круто

[@L.R.NatioN]

only a dream

[@ERT342]

Пожалуйста подскажите какой металл используете

[@summitsecuritysouth724]

what size is the engine?

[@tilvikramlimbu743]

Sir l like your bike,can you made for me, please,

[@PhilsHobbyRoom]

Why do you always hang your muffler so low it drags lol

[@ysq58r-j6jx9du1]

класс

[@عليالجراحالجراح-ي1ش]

Naic

[@saefgaemover8686]

QUICK QUESTION how much it cost

[@kotofeix2]

Всё не плохо, но твоя сварка, явно надоела.Нам что тоже маски одевать при просмотре?😅😅😅

[@cody181818]

2 things. the pillow blocks on the swing arm and axel go on the botton not the top. and the exhaust is in a extremly bad place. if you ever bottom out you will snap it off and destroy the motor.

[@incognidraw]

Muestra las medidas por favvor

[@hamidalhaju4086]

😎

[@user-youtube-lada]

Хочешь ослепнуть? Смотри до конца...

[@Дмитрий-о6л3р]

Всё прекрасно , но глушитель на земле всё испортил .

[@eduardbozchenko4154]

Глушитель чисто до первой кочки хорошей, а конец маятника в 5см от земли это просто треш

[@АлександрЛеончиков-е8д]

А то что он из фольги тебя не смущает? XD )))

[@ave764]

качество сварки? не смущает?

[@alexandrrivo1208]

*_да ладно вам ! ... парень за сорок минут такой байк смастрячил ... ещё и гоняет на нём !!_*😅

[@ridhwaanridz8270]

can u give me all the plan plzz

[@prolska]

why

[@Cree_running_rabbit]

Just watch this video over and over again and pause the video and write everything down that you need to build yourself a homemade four wheeler my friend okay

[@alisartas4450]

@@prolska i

[@user-cm3hf2bx8v]

😅😮😅😅😅😅😮😅😅

[@AnotherCG]

No

[@mohdsaifulmohdsaid852]

4x4?

[@tfritz9068]

Hey bro, I'm disabled so I can't build one myself and I can't afford even Chinese bikes, let alone a Honda or other name brand... Would you be willing to build one and sell it to me? (Depending on location, of course.)

[@CHERALAUTO]

I appreciate your interest in my work, but unfortunately, I am not currently taking any orders for building and selling cars or go-karts. However, I hope you can find a way to get a bike or a vehicle that suits your needs. All the best to you.

[@bobboboff5326]

5:22 строительная шпилька на рычаге 🤮. Дальше можно не смотреть 👎

[@hildebertocarreiro9232]

Got blue prints and measurements ...

[@DrissB-og6sc]

Le taux d’ouvre défirent a trois

[@ravishekhar9274]

Kitana cost aata hai

[@mixman4309]

καλο το εργο σου αλλα δειχνεις πολυ ηλεκτροκολληση και κουραζει τα ματια!!!😵😵😵😵😵😵😵😵

[@nildasalceda7673]

RsAaaseserr278😂9😃22scdas11