Does this applies to to the coloured screen version ,I can same screen and buttons but it’s in colour and laid out a tiny bit different didn’t want to press anything just in case
@peddeler22 ай бұрын
nobody ever mention the other features, holding down the up and middle buttons for a few seconds will cycle through a few more features, top speed, average speed and most importantly, for me anyway, is actual battery voltage, and I think the forth one is trip time.
@BoscoLeАй бұрын
Thanks G
@Lolly9225 күн бұрын
I have just got mine and it doesn’t tell me my speed
@itz.sc24373 ай бұрын
Currently I’m running a 1500w mtx rear wheel with 52v battery I set the voltage on the sw900 display as 48 due to no option for 52. It has been riding good past few weeks but now screen keeps coming up with error 06 and can’t fix it tried evrything
@user-2uf2kr2c3 ай бұрын
Hi, does this display have a ambient temp mode? And what do you need besides this display and a relevant controller to mod a bike? Regards
@pyroadrian8604Ай бұрын
How csn i fix erro 024
@talgi0303Ай бұрын
i love you ty
@theheavenlychanneltv85393 ай бұрын
Mine is 1500w 48v…it’s showing error 08, I have checked the throttle over and over again but can’t find any disconnections. Please what do I do?
@G-VOLT3 ай бұрын
It may be a fault on the controller if you've tried new throttles. A faulty pedal assist can also cause this fault so check that over if you have it installed.
@Thecolorsquadofficial_orignalАй бұрын
Hi dear,how to fix error code 08. Thanks
@G-VOLTАй бұрын
A new throttle should fix the problem.
@ptaylor812 ай бұрын
Am not getting a speed reading unless the motor is in use. Also if I set it to the correct wheel size it reads at least twice the speed am travelling. Any ideas?
@G-VOLT2 ай бұрын
The only time I've seen the speed readings not show is when the controller and display are miss matched, are you using an sw900 with a DC moto controller? With the speed reading being inaccurate it's worth checking setting P07, that may need adjusting with the wheel size.
@ptaylor812 ай бұрын
@@G-VOLT yeah. Dc motor controller and the sw900 display. Only part of my kit that's not brand new is the battery. Recently upgraded from 36v 350 watt to 36v 500. Just can't figure out what's wrong. Had to set my wheel size to 10 inch to even get close to true readings. Burning my head out it is!
@G-VOLT2 ай бұрын
@ptaylor81 There's no reason why changing the battery would cause this problem. Did you manage to see what setting p07 is set to? Also did this start happening randomly?
@ptaylor812 ай бұрын
@@G-VOLT P07 is set at 46. I bought a brand new 36v 350 watt carrare from ebay last September. But wanted slightly more power. So bought a 36v 500 watt kit. Had it fitted professionally the other week. But instantly it would not give speed readings unless the motor is in use. And the speed was like 40 mph. Even though the wheel size was set correct. The guy who fitted it is confused as I am
@G-VOLT2 ай бұрын
@ptaylor81 I can't think of an explanation for that one, if it was my bike I'd start by trying a different display. Also check the hall sensor wires are all connected to the same colour in the white block connection from motor to controller, these 5 or 6 small wires carry the speed information from the motor to the display so you may have a miss match down there or a damaged pin.
@freedomofmotion4 ай бұрын
I purchased a bike with this lcd recently but the settings menu has a pincode. Is there a default code? Or hard reset option?
@G-VOLT4 ай бұрын
The manufacturer must have set this, I'm not sure why! If they didn't provide any paperwork including the pin code with the sale you may have to get in touch with the seller for that one
@freedomofmotion4 ай бұрын
@@G-VOLT Unfortunately I bought it second hand. It's an Allegro model but there's scant information online about them. Not a website or anything.
@outandaboutsince19863 ай бұрын
Are you sure its the sw900 not the kt lcd because I can't password the sw900 lcd screen. And I have both lcd on different bikes and can only password the kt lcd
@outandaboutsince19863 ай бұрын
Failing thst just buy a new lcd and follow this great instructional video 📹 👌
@freedomofmotion3 ай бұрын
@@outandaboutsince1986 Yeah I'm certain unless KT also have one with the same model number and design. I think the unused code in the manual enables pin code if I remember correctly. In the manual it says" not yet in use"
@Dascrane4 ай бұрын
What’s error 3
@G-VOLT4 ай бұрын
That can mean PAS issues on some setups.
@MGWAIKIDOJITSU5 ай бұрын
Hiya I have just installed a new sw900 it has two connectors a large 5 wire connecter and a tiny two wire connector, I have no idea where this one plugs in ? Do you know at all , my old lcd screen died but only had one 5 pin which plugs in no problem ,,cheers
@G-VOLT5 ай бұрын
Hi, I've never used one, but I believe the 2 wire connection is for a headlight 👍
@MGWAIKIDOJITSU5 ай бұрын
Hi that sounds about right cheers
@jasonbuchanan75913 ай бұрын
Just bought a bike with a kit on Running hot So I can deactivate the throttle And limit it to 15.5 mph?
@G-VOLT3 ай бұрын
Yes, you can join the 2 matching wires together at the controller to set the limit and use the pedal assist instead of the throttle 👍
@desmondoloo6054Ай бұрын
How can i fix error 9
@noreengultiano34573 ай бұрын
what is e 010 means?
@kajjohnson3 ай бұрын
Check connection from motor to control box mine came unplugged plugged it back in all is fine
@AmirAhmad-pn4nk2 ай бұрын
I love this e kit but gets too much attention. My bike got robbed in the first week of having it 😢
@LugardJohalАй бұрын
I have error 10 coming up on my lcd, ive checked connections between screen and controller everything is fine????
@G-VOLTАй бұрын
You must have a fault in your display or controller, try a different display first then a new controller 👍
@ethangladstone15505 ай бұрын
how have do u get the 52v setting on the sw900 as im looking at a mtx 1500w 48v kit wanting to use a 52v 28.8ah battery and im pretty sure most of the sw900s come with 36,48,60,72 with no option for 52v in PO3
@G-VOLT5 ай бұрын
You're right, we had to ask the manufacturer to add the 52V setting so we could sell it with our 52V battery. It should work OK on the 48V mode but your battery level would most likely always show full on the display. I can take a look to see if we have any spare displays with the 52V setting if you'd like.
@ethangladstone15505 ай бұрын
@@G-VOLT its because im planning on building one in a month or two when i gather abit more money as i wanted to build a 52v 28.8ah and use a 1500w 48v mtx rim kit so it would be a good all arounder ebike! as i wanted too see the battery life on the display but not a huge problem its that since it recognises it as a 48v battery it may the battery v down too low as it thinks it still a 48v not a 52v.
@G-VOLT5 ай бұрын
@ethangladstone1550 It will be a good set up, the seller may be able to provide a 52V display and controller. Give us a shout if you need any parts, we're using the mtx rim on our 1500w kits now and we can sort you a discount code out 👍
@ethangladstone15505 ай бұрын
@@G-VOLT do u sell on ebay or ur own site gonna look into ur stuff ur selling also ive emailed this question to the seller so hopefully i get a response.
@G-VOLT5 ай бұрын
@ethangladstone1550 We sell on our website, which is www.g-volt.shop 👍
@Nottspiff3 ай бұрын
What would be a better controller to buy instead of a basic one?
@Jayven_-4 ай бұрын
When i turn my bike on everything works but the battery isn’t showing but the bike works perfectly fine. Can u help me?
@G-VOLT4 ай бұрын
The voltage on your display may be set higher than what your battery actually is.
@Marcus-qm3mv3 ай бұрын
Can you do a video on how to put the pas on if possible