And never, no matter how tempting it is, DONT try to clean a magnetic ring with another magnet to clean rust or metal debris because you are going to erase the magnetism printed strips of it. I know this because its on my shameful list of things I did wrong, when you go for a drive test after finishing the replace of a brand new bearing & hub kit the ABS/ESP fault light comes ON at the same time you remember that "Directed by Robert B. Weide" song
@TheGibby33403 жыл бұрын
Very good point. Mistakes (although at times extremely frustrating/costly) are part of the learning process. I have made countless mistakes over the decades and will continue to do so…We are human. Thx for watching 👍
@zb7060 Жыл бұрын
How long did you leave the bearing and hub in the freezer to shrink it?
@TheGibby3340 Жыл бұрын
Nothing too scientific about it. Think I threw it in the previous night. Thx for watching 🍻
@onezero704Ай бұрын
What happens if the abs wheel speed sensor breaks?
@TheGibby3340Ай бұрын
Loss of antilock braking, loss of traction control, loss of electronic stability program (vehicle stability augmentation) and loss of AWD mode of operation. If the vehicle is equipped with aforementioned. Thx for watching 🍻
@onezero704Ай бұрын
@@TheGibby3340 thanks mate.
@shadowopsairman15837 ай бұрын
What year and specific sx 4?
@TheGibby33407 ай бұрын
2007-2009’ 2L gasoline, hatch.
@didiercollot4285 ай бұрын
Merci pour le tuto👍
@TheGibby33405 ай бұрын
De rien et merci d'avoir regardé 🍻
@avenfisher97959 ай бұрын
What year SX4 is this?
@TheGibby33409 ай бұрын
2007-2009’ Thx for watching 🍻
@iansworkshop3 жыл бұрын
Brilliant job and video Ian , one of those jobs you dread to start , but very satisfying when finished , cheers 👍
@TheGibby33403 жыл бұрын
Cheers Ian 👍
@albertnel74682 жыл бұрын
Thank you for the info on the magnetic side of bearing!
@TheGibby33402 жыл бұрын
Thx for watching. Cheers 👍
@Automotive_Solutions3 жыл бұрын
Top job. I must admit I prefer your commentry to the silent movie version 😅.
@TheGibby33403 жыл бұрын
Cheers Iain. Think I had my little press near its limits 🤣
@stephanhughes8164 Жыл бұрын
Fantastic content, thank you!!
@TheGibby3340 Жыл бұрын
Thank you Sir and Thx for watching 🍻
@JohnnysSpeedShop3 жыл бұрын
Nice work mate...job well done and I'm sure no more rumble 🤣🤣
@TheGibby33403 жыл бұрын
Cheers Johnny 👍
@winrampen1174 Жыл бұрын
Many thanks for your extremely helpful video. Although I'm from Oakville, Ontario - I'm writing from Scotland - where I've just succeeded in changing my front wheel bearing. Your help travels far and wide! Two points which may be useful: 1. I was having trouble with the track rod end nut (actually the rusty cotterpin) and ended up undoing the track rod - which is less likely to be seized - though you need to ensure that you don't alter the nut position. and 2. I used a bit of 12mm studding with mudguard washers to hold the hub upside down in my drill press. Going at low speed (100 RPM-ish) I played a torch on the bearing inner, which got to about blue heat and then dropped off. Very easy if you have a torch.
@TheGibby3340 Жыл бұрын
Just saw yer comment. I was watching the old firm match 😁. Thx for the kind words. Some good tips. What took you to Scotland if you don’t mind me asking?
@winrampen1174 Жыл бұрын
@@TheGibby3340 I came here 45 years ago to work on renewable energy at the University of Edinburgh - which I thought might last two years........ Two companies, one wife, three children, multiple grandchildren later and I'm still here. Much more mountainous than Ontario, and very few shopping malls - what's not to like!
@TheGibby3340 Жыл бұрын
@@winrampen1174 Nice. I’ve been in Canada for 48 years now. So far more Canadian than Scottish, truth be told. I’m glad Scotland didn’t disappoint. 🍻
@theGADGETSplaylist3 жыл бұрын
I like that small press and that slide hammer. well done Ian!
@TheGibby33403 жыл бұрын
They have came in handy over the years . They sit doing nothing for very long stretches, but when you need them…Cheers Denis 👍
@bleebleblahble88333 жыл бұрын
Need to do this on the fiesta at some point alongside front axle seals. Thanks for making it seem manageable.
@TheGibby33403 жыл бұрын
Thx for watching 👍
@GoldenSim272 жыл бұрын
Thank you sir
@TheGibby33402 жыл бұрын
Thx for watching. Cheers 👍
@joanieolson74272 жыл бұрын
Could you let me know where I can get the circlips for the front bearings?
@TheGibby33402 жыл бұрын
They were purchased from Suzuki. If you live in Canada or the States, google Suzuki authorized dealer and you can still obtain SGP locally.
@joanieolson74272 жыл бұрын
@@TheGibby3340 Thanks very much. I'll have my parts next week. (I live in Ottawa)
@mechanicmatt8713 жыл бұрын
Good job mate , great video 👍
@TheGibby33403 жыл бұрын
Cheers Matt 👍
@Dreadmyshadow2 жыл бұрын
That sure looks like a southern car to me
@TheGibby33402 жыл бұрын
It is a “southern” car. Southern Ontario Canada 😃
@Dreadmyshadow2 жыл бұрын
Lol lucky here in CNY that thing would be a rusted mess