SX4 Strut Replacement

Long, long overdue!

[@Ratzez2]

Great Sx4 vid! Appreciate the effort! FYI; those 09103-14032 strut bolts can be replaced with Specialty Products Part No. 81260 -- to adjust the camber ±1.75° on the wheel :)

[@TheGibby3340]

Thx. And thx for the details 👍

[@zmanvideo1]

another fine sx4 repair video, thank you!!!

[@TheGibby3340]

Thanks again. Cheers 👍

[@tomakram872]

Nice video thanks ive 08 sx4 so going through the video thanks again 👍🏾

[@TheGibby3340]

Thx for watching. Cheers 👍

[@brianneu6489]

Quick question...I replaced my front struts on my 2007 SX4 a while back, all KYB parts used. All new strut KYB rubber strut mounts and all. On the FSM exploded diagram you show on your video, I have a small gap between the top plate #10, and the vehicle body when fully assembled. The top plate #10, bottoms out on the nut #9 below it and I cannot tighten it down anymore to close this gap. I have a slight rattle when going over bumps and it is due to this gap that I can't seem to close. I replaced this top plate #10 with a genuine Suzuki part as well thinking the KYB plate may have been incorrectly manufactured but it was no different upon receiving the genuine Suzuki part. I checked if the nut #9 is the correct height, and it seems to be, and the insulator bushing below (on the underside of the strut body cavity) is a KYB branded bushing so I assume it is the correct depth. I can't tell from your video, but did you end up with any kind of gap between the top plate #10 and the body of the vehicle once the vehicle was back on the ground and the struts were fully supporting the vehicles weight? Appreciate the videos.

[@TheGibby3340]

Well I don’t know off hand. I will look over the references you mention. I mark the components so they are reassembled in the correct orientation. I think the top mount/bearing does have an indexing mark. And must be positioned correctly. I know in the past I have had to retorque the mount studs with the weight on wheels as I had a squeak. 🤔

[@Takeoffin321]

Thanks I'll be doing this soon. Just picked up a 09 for $1500..

[@TheGibby3340]

👍 Thx for watching 🍻

[@jasonwiggins7894]

So you don't have to undo the drive shaft nuts for clearance...that's great..cheers

[@TheGibby3340]

Thx for watching 👍

[@davesterl]

I had that on a suzuki where the aftermarket bearing was different in appearance to the original

[@TheGibby3340]

Mount & bearing not even close Dave. ”Moog”…not a fan. Cheers Pal enjoy the race 👍

[@danycastillo104]

buy the same .. shock absorbers .. change all the steering parts .. and it still makes noise when I go through bad streets it makes a noise like knocking

[@TheGibby3340]

Closely scrutinize the exhaust system…Missing or damaged hangers can result in undertray contact. Check near the sub frame and muffler. If it’s a AWD also check near the hanger bearing. I have experience this on my SX4’s.

[@tedzgred1723]

What's the year and engine of this specific Suzuki ? Mine is from 2007, 1995 ccm, I wonder if the same strut will fit.

[@TheGibby3340]

2009’ 2L Hatch. You might want to consider “Rockauto.com” website. They have a very comprehensive parts determination facility. Thx for watching.

[@tedzgred1723]

@@TheGibby3340 Thx a lot

[@spooky5338]

My passenger side strut is leaking oil. I don't mess with springs, so I plan on getting the complete KYB strut assembly with a new spring already installed. Is there a difference in struts between the AWD and 2WD model? I need to order for the AWD.

[@TheGibby3340]

The quick strut makes a lot of sense. Especially if you run into a broken spring 😡 Not certain about a 2wd AWD difference. Don’t believe so.🍻

[@spooky5338]

Alright, I don't really see any other options for struts other than the KYB assembly. The car has about 154,700 miles on it, and I don't know how the previous owner maintained it. It's just safer, and better for the car if I just get a pair of struts with springs & mounts for $350 USD after shipping and tax.

[@TheGibby3340]

The next video may explain the situation in a little more detail.

[@CarsExposed]

Top job mate , KYB parts is very decent it should last a long long time 👍

[@TheGibby3340]

Thx Igor. I got lucky this time…In the past I spent hours removing those 4 bolts. With your experience, you are well aware of how trying it can be at times I am sure…Cheers Pal 👍

[@lisaelaine7249]

Well looks like I got myself a job in replacing mine.

[@TheGibby3340]

Good luck. It’s not too difficult…Just take your time. Cheers 👍

[@theGADGETSplaylist]

lot$ of $hop dollar$ $aved, Ian:)

[@TheGibby3340]

Cheers Denis…Hope your enjoying the Summer! Incredible temperatures out West ??? Little scary 😳

[@theGADGETSplaylist]

@@TheGibby3340 pronounced jetstream that bought them that heat also responsible for cooler than normal summer for us so far 2moro will be 1st hot day...I'll take it!

[@Automotive_Solutions]

Always satisfaction getting that top strut nut back on when your using those widow makers. For the wiper arms I use something similar to this.... amzn.to/2SKzIY5 👍😁

[@TheGibby3340]

Yeah they are scary I must admit…I have a number of small pullers Iain. The issue was the lower edge of the arm casting is well below the close fitting plastic shroud???? Head scratcher 🤔 Thx & Cheers 👍

[@andrewmason7207]

my car is a sx4 gl and i keep getting sent the wrong strut , any help..

[@andrewmason7207]

its 2008 2 wheel drive

[@msaudiosystems]

Nice video. How did you find the parts numbers for the screws and nuts to replace ?. I'm trying to find them for my Sx4 2012 . Thanks

[@TheGibby3340]

My local Infinity dealership (former Suzuki, former Nissan) still supplies SGP. I am on very good terms with the fella at the parts desk. Thx for watching 🍻

[@TheGibby3340]

This video at 4:38 contains his contact details. He can ship parts, if your stuck. kzbin.info/www/bejne/bmatp2eLl6qVfbMsi=FcESqt8Fjd-dxlMU

[@msaudiosystems]

@@TheGibby3340 thanks !

[@JohnnysSpeedShop]

Very thorough mate...

[@TheGibby3340]

Cheers Johnny…Don’t know if you noticed the masking tape on the windshield…Little trick an Irish fella passed on for wiper position 😃

[@JohnnysSpeedShop]

@@TheGibby3340 😁😁😁

[@msaudiosystems]

Nice video !. Great job !. Question. When do we need to replace the springs ? .

[@TheGibby3340]

Thx for watching. Unless they have been grossly overloaded, suffering from extreme corrosion, physically damaged or no longer capable of maintaining the vehicle in a road worthy attitude under load they should remain fit for service. The dampers (shocks) however do have a limited life cycle. 🍺

[@iansworkshop]

Great video there Ian , I don’t like f**king about with springs , so I always put extra spring compressors on lol , enjoyed that , cheers 🍺👍

[@TheGibby3340]

I don’t like swearing in my videos as a rule Ian, but if it saves somebody’s neck…Cheers 👍

[@iansworkshop]

@@TheGibby3340 yeah , deffo , as it put the message across quite clearly , it’s something you don’t take lightly, 👍

[@iansworkshop]

@@TheGibby3340 got a wee present today Ian from the other half for my 50 th coming in September, …. So will be posting tomorrow, when I make the video lol , hope you enjoy 👍

[@TheGibby3340]

@@iansworkshop I’ll keep an eye 👍