I drilled a small hole in the middle of the air cleaner. Spray a dash of starter fluid thru the hole with the thin straw that comes with the bottle. It’ll crank on the 1st pull every time.
@RobbiRocks11 ай бұрын
Only found you here now, This has been so very much helpful info, huge thanks for posting this.. Also Extra thanks for having no annoying back ground music, Cheers..
@Josh2024Garcia Жыл бұрын
Our little Syx 50 needed a new draw sting kit too but other than that she runs and and runs with a new plug now and then. Cool little camp bike for the kids
@plumbherhub1664 Жыл бұрын
The 12mm impact trick is dope
@isaacboozer28918 ай бұрын
I have a 125cc dirt bike and yours a beauty im ready to ride again Amen 🙏❤️
@murphyking792 жыл бұрын
You actually do a very good job working on the motor. I would trust you to work on my things. It's rare I say that!
@MarleyJaxGarage2 жыл бұрын
Thanks man, I appreciate all the comments!
@rogerhaas87734 ай бұрын
Wow! A great tutorial video that step by step clearly trouble shoots and fixes no spark m/running issues. Thank u!
@maredansmaredans8575Ай бұрын
Hey great video:) Just got one like this for my girl, i suspecting the guy i got it from messed up the wirering. Could you give a short tour of the wireing? Thanks.
@treasuretotrash20672 жыл бұрын
Nice job on the repair, no complaints
@MarleyJaxGarage2 жыл бұрын
Thanks for watching!
@spymaine892 жыл бұрын
new pull starter new coil new sparkplug even though the coil tested good the new coil got spark very good test and run.
@MarleyJaxGarage2 жыл бұрын
Thanks for watching.
@isaacboozer28918 ай бұрын
Yeah she will be good just a little care Im like Bike Life fr ❤🎉😊Amen 🙌👏🙏
@aaronmarcel50262 жыл бұрын
Hey I brought and put the coil pack on, it didn’t work.. Didn’t check like you did for spark, but when taking the wire off the spark plug it came apart.. I will buy another and try again…. If that doesn’t work, any suggestions? Brand new dirt bike, grandson only rode this thing about 20 miles at best…. Hoping it can be fixed cheaply…. Thanks again your videos gives me hope that I can get it fixed….
@MarleyJaxGarage2 жыл бұрын
Hey thanks for watching. My suggestion would be to narrow down the problem. It could be 1 of 3 things. No spark which would mean the coil/stator/kill switch might have an issue. No compression which usually means piston/cylinder problems. Or lastly, lack of fuel pointing to an issue in the carburetor. As long as it’s not a compression issues it should be cheap and easy to fix. I would start with spark like I showed. Then check and see if the spark plug is wet or dry. Could pour a small amount of gas down the cylinder to see if it will pop over. Compression you will either need to rent/borrow/buy the equipment. Hope you get it running again.
@aaronmarcel50262 жыл бұрын
@@MarleyJaxGarage thanks again for the advise, Im gonna buy another coil and go from there…. Can’t believe it’s a big issue it’s basically still brand new…. I’m most appreciative….
@MarleyJaxGarage2 жыл бұрын
@@aaronmarcel5026 yea these bikes are made with cheap parts and I don’t think the quality assurance is too good coming out of the factory. Once you get all the kinks worked out it should last a while.
@johnnySMALLpepper Жыл бұрын
Great Video Bud. Going to go through this today. Excellent.
@mrbrownz554 Жыл бұрын
Wagon wheel
@aaronmarcel50262 жыл бұрын
My grandson has the same bike, still basically brand new, put it up when it got cold, would not start the next year.. Put new spark plug in still won’t start, wondering how hard it is for a new coil…. My grandson if not happy….
@MarleyJaxGarage2 жыл бұрын
A new coil is pretty easy to put on. Only about 5 bolts total, three on the pull start cover and two for the coil. It could also be bad gas in the carburetor since it sat for a while so I would check and make sure it doesn’t have spark before changing it out.
@richardwilkinson44192 жыл бұрын
My 4 year old son has one of these, he gives it the beans
@MarleyJaxGarage2 жыл бұрын
Yea they seem to be pretty decent when they want to run. I just wish they were a little more reliable.
@jessecantu27012 жыл бұрын
Do you have any videos on adjusting the brakes and idle? Would be really helpful thanks 💯
@MarleyJaxGarage2 жыл бұрын
I think that dirtbike is broken again so it should be showing up in a video soon.
@AddiDaddi42 жыл бұрын
there should be a flathead screw under the carb and twisting that will adjust the idle
@spencerespinola882 жыл бұрын
Do you think these forks will fit on a razor? I saw a cheap one on marketplace and was wondering if any parts might be able to swap over.
@MarleyJaxGarage2 жыл бұрын
For razors I have found mountain bike forks are closer to the design.
@154landon34 ай бұрын
Where did you get your coil? Great video
@altmandma2 жыл бұрын
Thanks for making this video! I have the exact same problem.
@MarleyJaxGarage2 жыл бұрын
Thanks for watching.
@mikereppert972 жыл бұрын
Did you replace your coil? I just pulled my sons out of the garage and can’t get it started, think spark is the issue for mine as well
@altmandma2 жыл бұрын
@@mikereppert97 I did yes. I keep trying to link you to the one thay did the Trick but my comments keep disappearing
@christianrodriguez80362 жыл бұрын
I was watching your video because I have the same one but the one I have the switch on is on the right side more or less where the struck is and it also has the green power button for the green starter and the red power button when I hit the green button with a jumpstar and leave the green button pressed it is as if it were on but I stop pressing the button and it does nothing I changed the new ignition and still had the same problem but I see your video and check if it has sparks and I don't see any sparks, remove the coil and use the voltmeter and it gives the same reading that it told you... now that you recommend me because it is new and I have not been able to use the motocross
@MarleyJaxGarage2 жыл бұрын
I would put a new coil on it and see if you have spark.
@cajunman73892 жыл бұрын
I just bought this same bike. Do you happen to know if there is a stator on it? Also would you happen to know if its possible to run a small LED light bar off the coil or stator if it has one? Thanks
@MarleyJaxGarage2 жыл бұрын
It’s just a flywheel and pickup coil no stator. You could just run a battery led light bar should last a long time.
@patricwell8335 Жыл бұрын
I know it's 1 years old...the coil you mention is got mangnent...is that built with it cuz mine does have one or not good
@cjumberger74892 жыл бұрын
Is there a part number for that coil? I’ve found it on their website but they’re out of stock. You think Home Depot or Lowe’s carries one that’ll fit?
@MarleyJaxGarage2 жыл бұрын
Look up L7T spark plug coils on Amazon. Their are a couple cheap ones listed. The one I got is no longer available.
@joshstepp48452 жыл бұрын
I just bought one on ebay, will be here in a week
@dariusjones7942 жыл бұрын
Can you help me with my sons dirt bike he has a X pro 50cc bike from powersportsmax and this thing just doesn’t want to start
@MarleyJaxGarage2 жыл бұрын
Does it have spark and compression? What have you tried so far?
@dariusjones7942 жыл бұрын
@@MarleyJaxGarage so I am not getting a spark at all and gas is leaking from carburetor
@angellucero8043 Жыл бұрын
What NGK spark plug you used?
@markanthonyvincent5971 Жыл бұрын
I have a 49cc quad, brand new/clean carb, new pullstarter, the sparkplug works i have shocked myself with it. But the quad wont fire up when its alltogether. what else could i change or clean that i havent allready?
@IcyType111 ай бұрын
So I got a 49cc q2 from a friend since he couldnt fix the spring retraction on the pull start, I fixed that and pull start feels very heavy and janky like it chews a couple of times in the time I pull the string, I removed the spark to check that and was no problem,I also tested the pull without the spark and it pulled smoothly so not a compression issue either. I hear/see the flywheel cranking when I pull so I put some wd40 in the spark socket and nothing but a little bit of smoke! It’s only like a week old aswell and friend bought it brand new. any ideas?
@ML-uu7wy8 ай бұрын
On our three bike you have to hold the left break to get spark?..,.?
@KF-im5qp2 жыл бұрын
Just picked up 2 of these used.....they both started and ran great the other day. I get home, only one starts. I took off the pull start on the one that doesn't start.......off the bike, it pulls and spins correctly as it should but when I line it up back on the flywheel and pull = nothing happens (the flywheel won't spin?) something isn't correct. Wondering if I should just purchase another pull start but don't want the same thing to happen. Any input is greatly appreciated!!
@MarleyJaxGarage2 жыл бұрын
I had good luck switching from the plastic pull starter to the metal one. It seems to hold up better.
@sonoflamech7772 жыл бұрын
I got same problem ,but the pull cord was working then I put fuel in the tank ,then pull cord goes tough and clunky. Cnt buy new parts yet so might try the drill thing
@KF-im5qp2 жыл бұрын
I ordered the new pull start, good to go now
@伖2 жыл бұрын
@@MarleyJaxGarage hey sorry for replying but my bike wont start like the exhaust will make a sound but when i pull the the thingy it dosent start i have fuel in it to
@MarleyJaxGarage2 жыл бұрын
@@sonoflamech777 I would remove the spark plug and see if the cylinder is full of gas. Might be a stuck needle in the carburetor.
@SYXMOTO2 жыл бұрын
Thanks for sharing! We are working on improving our products.😄
@MarleyJaxGarage2 жыл бұрын
I uploaded another video specifically working on a stuck throttle and new carburetor if you want to get it working again. It should pretty simple to figure out what is going on. I don’t think you would even need to take the carburetor off.
@sandychou77352 жыл бұрын
It helps a lot
@MarleyJaxGarage2 жыл бұрын
Thanks for watching.
@nassatok5779 Жыл бұрын
That’s really help Thanks
@MarleyJaxGarage Жыл бұрын
Thanks for watching
@ohjesushesaiditagain.67482 жыл бұрын
Sounds sweet, what fuel/gas oil mixture are you using please. Thank you.
@MarleyJaxGarage2 жыл бұрын
I was using 32:1 for this bike.
@chevylandtv6702 жыл бұрын
After replacing my pull start the engine still want turn over, could the engine be lock up, I also tried that method with the drill trying to start the engine and it will not turn at all and tip or suggestion
@MarleyJaxGarage2 жыл бұрын
Will it turn over without the spark plug in it? Could be hydro locked or something. What went wrong with it that made you need to replace the pull start?
@Josh-fl4tl2 жыл бұрын
I think i had a similar issue, i went to clean my carb and when i put the carb back on i put one of the parts upside down, my crank shaft was hitting and wouldn’t turn.
@Nate202 жыл бұрын
Hey can you tell me where the black wire coming off the engine goes i took mine off and replace but cant remember where to connect
@MarleyJaxGarage2 жыл бұрын
It connects to the red wire on the frame.
@Nate202 жыл бұрын
@@MarleyJaxGarage so i cut the ends and connect ? They have two different endings
@MarleyJaxGarage2 жыл бұрын
Mine was a bullet connector. Check my video at 6:30 to see the black and red wire together.
@Nate202 жыл бұрын
@@MarleyJaxGarage you wouldn’t understand how long ive been trying to figure this out but since the connections are different i can just cut them and twist than use eletric tape ?
@MarleyJaxGarage2 жыл бұрын
@@Nate20 The connections should be the same unless you changed the black wire. What kind of connectors do you have? I would put connectors on them so you can easily disconnect. For testing you could just use a wire nut to make sure it will work.
@CharmLampies4 ай бұрын
What can be the cause for sparks coming from the side of engin
@RCasperson2 жыл бұрын
Do you know the correct ohms the coil is suppose to have ? I believe my sons has the same issue. No spark, carb is good.
@MarleyJaxGarage2 жыл бұрын
The secondary resistance seemed to be fine, it should be .5-3 ohms. The primary resistance was the problem, I believe that should be between 6,000-12,500 ohms.
@TylerKnight-xo2dl7 ай бұрын
What kind of 2 cycle oil do you use
@moparjay143Ай бұрын
Can you link the Ignition coil
@905mudboysdc42 жыл бұрын
Do a vid on how to get it to idele without any throttle can’t figure that out on the nephews bike
@MarleyJaxGarage2 жыл бұрын
Check out my other video on the syx. I put a new carburetor on and adjusted the idle.
@905mudboysdc42 жыл бұрын
@@MarleyJaxGarage appreciate that bro
@noahsk85262 жыл бұрын
THANK YOU :D
@MarleyJaxGarage2 жыл бұрын
Thanks for watching
@rakeandbakeАй бұрын
Can anyone help, I’ve same bike and at the side where the pull cord goes there’s 2 green wires any help where they get mounted?
@murphyking792 жыл бұрын
I agree, first thing fix those atrocious angled levers! I couldn't look at that bike with levers facing the heavens.. lol
@touchpointpropertymanageme2889 Жыл бұрын
Great video
@edgarandrade6082 жыл бұрын
Hey bro so the coil is not supposed to touch the flywheel cause I have spark but my coil the metal is touching the flywheel
@MarleyJaxGarage2 жыл бұрын
No, the coil should be close but not touching the flywheel. Look at the video here kzbin.info/www/bejne/eJzEq3qqecqdjas (4:15) where I show placing the index card between the magnet and the flywheel.
@anthonyiachello62672 жыл бұрын
How many ohms was the replacement coil?
@rileychapman11722 жыл бұрын
This happend to me and we got the same pull starter
@resw1974 Жыл бұрын
I have a similar bike I bought for my son it's a x pro 50cc and the flywheel will not turn, what could that be
@MarleyJaxGarage Жыл бұрын
Piston could be seized. What happened before it locked up?
@anaterrones266111 ай бұрын
how should the carburetor be set
@fetsgaming57403 ай бұрын
What is the coil called?
@bobyekmi322 жыл бұрын
good job bro ,i subscribed
@MarleyJaxGarage2 жыл бұрын
Appreciate it man.
@darrendickson81822 жыл бұрын
I need some help same sort of bike 2016 model won’t start bro
@MarleyJaxGarage2 жыл бұрын
What’s wrong with it? Have you narrowed it down at all?
@darrendickson81822 жыл бұрын
@@MarleyJaxGarage not yet no but I will today
@mamiecook72762 жыл бұрын
So the clicking noise that your bike was making at first that's normal?
@MarleyJaxGarage2 жыл бұрын
What time of the video did you hear it? The starter recoil definitely makes a clicking noise.
@mamiecook72762 жыл бұрын
2:21
@MarleyJaxGarage2 жыл бұрын
I think you were just hearing my ratchet clicking.
@mamiecook72762 жыл бұрын
@@MarleyJaxGarage the noise is when your pulling starter
@MarleyJaxGarage2 жыл бұрын
That is the starter recoil and is normal.
@sayblaze2 жыл бұрын
I got a xpro hawk 50cc brand new it won't start i put a new carburetor on it and it won't start I try everything I even change the spark plug won't start it a video on my KZbin of it please help
@MarleyJaxGarage2 жыл бұрын
It is most likely a spark or fuel problem. When you changed the carburetor was the old one full of gas? There should be a screw on the bottom to drain it, you can loosen it up and make sure gas drips out of the bottom. When you put a new spark plug in did you check and make sure the plug was sparking? If you put the end of the plug against the motor to ground it out and pull on it you should see spark. I have heard of them coming from the factory with bad coils.
@MarleyJaxGarage2 жыл бұрын
I have another video going through the carb too.
@sayblaze2 жыл бұрын
@@MarleyJaxGarage there was no gas coming out the carb it was brand new from the factory and there no spark coming out there against the motor I try it Today the last time it came on it stay on a few seconds and when you throttle it cut off immediately
@Mxman100 Жыл бұрын
When checking spark always turn a light off
@nobles20228 ай бұрын
👍🏻👍🏻👍🏻
@kalyddessalines7692 жыл бұрын
What's the name of the metal pull starter that you bought off amazon?
Nothing should be actually touching the flywheel. If it is touching it could wear down the magnets and cause the motor to be out of balance or break the flywheel.
@SYXMOTO2 жыл бұрын
Can I share it on our social media and website please?
@MarleyJaxGarage2 жыл бұрын
Yes you can.
@DmonDhaBoss2 жыл бұрын
How is this a common problem you people need to send out bikes that have good coils and good parts not defective you should have quality control and have someone that test all the bikes
@MarleyJaxGarage2 жыл бұрын
@DmonDhaBoss to be fair it was working when they sent it out. It just didn’t last very long. I think it’s more of a case of you get what you pay for when buying a complete dirtbike for 350 dollars. I tell anyone that asks about them they should only buy if they know how to work on them. The quality can only be so good at that price point.
@DmonDhaBoss2 жыл бұрын
@@MarleyJaxGarage yeah I just bought a second bike last week and it never started I'm waiting for a response I returned the first one it worked for a week this one never even started. I get that you get what you pay for but the company shouldn't sell items that are non usable. They should sell frames and parts if they can't make sure the whole bike runs.
@DmonDhaBoss2 жыл бұрын
The BBB has many complaints for this company and all they can do is refund. I also payed 475 for this bike when 2 years ago it was 320
@JanetteColon Жыл бұрын
Good Video, easy explanation! You are good!
@acfrancis21182 жыл бұрын
Can you link the coil on amazon?
@MarleyJaxGarage2 жыл бұрын
Look up L7T spark plug coils on Amazon. Their are a couple cheap ones listed. The one I got is no longer available.
@qamarularol7782 Жыл бұрын
What size the wheel?
@MrMkirk232 жыл бұрын
Dude I an livid right now. Ordered two for my kids for christmas. First one has had ZERO issues. The second, third and now FOURTH wont start. Its crazy because on this last one I literally started it before even putting it together. Now that I spent two hours putting it all together it refuses to start. This company is GARBAGE. BEWARE.
@MarleyJaxGarage2 жыл бұрын
Yea I think they are definitely having some quality control issues. I am making another video now since it came back not running again. Definitely would not recommend someone buying one of these unless they know how to work on small engines.
@Gigaspear2 жыл бұрын
i reccomend klx110L for both of them
@peterdudy32033 жыл бұрын
I need the same pull štartér
@MarleyJaxGarage3 жыл бұрын
I got it off amazon. www.amazon.com/HIAORS-Recoil-Starter-Screws-Coolster/dp/B08LD33R2G?ref_=ast_sto_dp
@jaymartin94682 жыл бұрын
Where does this shop from like what state?
@MarleyJaxGarage2 жыл бұрын
I’m not sure what you mean. It is shipped by Amazon so it should come from your nearest distribution center. I’m sure the actual manufacturer is a Chinese company if that’s what your asking.
@venumriot82982 жыл бұрын
My wife is having the same issue with hers
@MarleyJaxGarage2 жыл бұрын
Let me know if you have any questions. All parts are linked in the description.
@mar1z453 Жыл бұрын
Can anyone tell me how to lower the speed of this thing ? As soon I start it it speed by it self lol ? I try everything
@markcasarez4472 жыл бұрын
Links to the parts?
@MarleyJaxGarage2 жыл бұрын
I added all the parts to the description.
@henrivanderriet38952 жыл бұрын
I'm sure you meant to say the multimeter is on 20K Ohms , not Ohms. I zoomed into the dial to check.
@MarleyJaxGarage2 жыл бұрын
Yes good catch and thanks for watching.
@Talon-62 жыл бұрын
These things are not worth it I've had nothing but problems with my son's bike it's spends more time broke than running
@MarleyJaxGarage2 жыл бұрын
You pretty much spend as much time working on them as riding them.
@mrbrownz554 Жыл бұрын
Correct but worth fitting a new spark plug and coil
@theestatesboyandgirl33842 жыл бұрын
dude your choke was full choke it has to be no joke for it to start
@MarleyJaxGarage2 жыл бұрын
Why do you say that? The chokes only real purpose is to help start the motor when it’s cold. I have worked on a few of these and they all seem to have fuel starvation issues. I wish they made these with fuel mixture screws instead of just the idle adjustment.
@chucknorris2952 Жыл бұрын
@@MarleyJaxGarage mine is extremely heavy to pull, is there any compression release on these that i havent found?
@ronprice1989 Жыл бұрын
That e3 plug is not a cheap plug lol
@ARTVGAMING2 ай бұрын
I have no idea why i bought TWO of these in the past. First one broke down, second one broke down 2 months after driving. These things are just a full on scam for people. I,agine you dont know technical stuff ... you cant fix it!
@AnthonyGarcia-st6jd Жыл бұрын
Teach ya kids how to bump start 100% works n never by another cheap pull string
@Wk32eze2 жыл бұрын
I have same piece of shit bike only work once
@MarleyJaxGarage2 жыл бұрын
Yea would not recommend anyone buy one, but seems like a lot of people already have.
@CantonDrummer852 жыл бұрын
Absolute garbage and really dangerous for kids. Bought the Holeshot 50cc and the throttle sticks wide open. It was a birthday gift for my daughter. When I contacted them they said they wouldn’t replace the defective parts because it was out of the 30 day warranty… i contacted them less than 60 days after purchase. I can’t let my daughter ride this thing, it’s dangerous! Total junk, buy from a reputable company that will replace defective and dangerous parts.
@MarleyJaxGarage2 жыл бұрын
I actually have the bike back with a stuck throttle and carb issues. Going to make a video on it this weekend hopefully so check back in a week.