table saw lathe for wooden rods / tapered rods possible as well [woodworking]

[@Strawdozz]

Was looking at several constructions, this seems to be the best.

[@nobuckle40]

That's much faster than using a lathe. And it would make tapering more consistent. Wonderful idea.

[@crossgrainwoodproductsltd9230]

The best, safest, and efficient doweling jig I have seen on YT! There is no waste like on most jigs that leave some square stock remaining. The adjustability both in diameter and length wise has not been addressed with other jigs I have seen. With the added bonus of making tampered stock as well!! Well thought out.

[@saundersd1962]

That’s on of the best designed jigs I’ve seen to to that. I’ll definitely use that at some point in the future

[@cyrilnorrie8450]

This is a great jig! I like the way that tapered turnings can be made, which are difficult to create with a perfectly gradual lathe even on a lathe! Thanks for sharing this and keep up the great work!

[@cyrilnorrie8450]

I meant to say a perfectly gradual taper!

[@ironwood3201]

It is the best method and the most efficient jig needed by every carpentry workshop. I will definitely make one

[@LKO-limbahkayuofficial]

Terimakasih telah membuat video untuk mempermudah membuat kaki meja retro... 👍

[@paulstanding7267]

That is a very well thought out jig and works very well 😀👍

[@rafaelkoga5762]

this is brilliant! thank you for always teaching us!!

[@СергейРогозин-ф1н]

Вот это я понимаю, отличная приспособа! Беру на вооружение! Для изготовления конусовидные ножек. Спасибо!

[@prjosenunojuniornuno8689]

Muito obrigado por compartilhar os seus conhecimentos

[@neildunbar1231]

Very clever, could put a see through cover to keep the wood chips inside for easier clean up.

[@Zie_carpentry]

Hello friend

[@punkrockviking]

That's a great idea! A removable plexiglass top!

[@MCsCreations]

Really excellent jig, man! Fantastic work! 😃 I'm definitely going to make something like that as well! Thanks!!! Stay safe there with your family! 🖖😊

[@youtukang]

👍👍😊

[@JoseGoncalves-zp2ws]

Parabéns, o melhor gabarito que eu vi no KZbin 🎉🎉🎉 parabéns!!!!! Que Deus abençoe sempre 🙏🙏🙏

[@warmconservatism2530]

언제봐도 깔끔하고 훌륭합니다~~👍👍👍

[@JoseSilveira-newhandleforYT]

Very good! Just like I commented in the previous jig 🙂

[@RANDYSWORKSHOP]

Great job, just a question: is the saw blade set 90 degree or with an angle?

[@Merito932]

Very smart idea and excellent execution 👍🏼

[@nonatowoodworkshop]

Brilhante projeto meu amigo.. muito eficiente e ajuda muito ter um gabarito destes.... Obrigado por compartilhar... Abraço.. 🛠️👍🏼

[@youtukang]

😊😊👍

[@Jazz-mb8rr]

Great work 😊❤

[@олегфёдоров-э7х]

Да сдесь за одни только подшипники можно 👍поставить, очень красивые! 😀

[@vicenteramirez8458]

Gracias por compartir la construcción de esta herramienta felicidades 👍👌 saludos desde México 🇲🇽🖖 y aquí seguimos al pendiente de tus vídeos 👋

[@владимиркислый-ы7б]

Превосходное устройство👍👍👍👍👍👍

[@RPPerry1984]

Are plans available for this? I'm sure I can figure it out, but you should really consider digital sales of your jigs.

[@agostinhodemenezes5618]

Otimo o melhor k ja vi,obrigado.

[@shihantemplet]

This is a commendable idea and design. I built a very similar device. I can confirm that it works for only short lengths. 4 feet or longer causes too much vibration in the center and the cut is too far in.

[@enryraleight1527]

Sir, excellent work. congratulations

[@Gus0046]

Un soporte muy útil para redondear. Muy buen trabajo amigo. Que tengas un excelente día. Un saludo.

[@youtukang]

😊😊😊

[@dilshancreation4172]

Its good👌

[@waheeddawodu9892]

Nice1 . Whats the material list? Thx brethren.

[@xkavehx]

Love this. What’s the name of the part at 4:34?

[@laichuenchen704]

Genious! I really like it!

[@ramosoficinadamadeira5510]

Parabéns projeto muito bom 👏👏👏👏👏

[@신승록-h9d]

만두 빗다가 보니 홍두깨로 보이네요 굳 아이디어

[@AndreiIR000]

Brilliant idea sir!!!

[@hmk3119]

베어링은 일반 볼베어링 쓰나요? 테이퍼 가공 할때는 자동조심베어링을 사용 해도 센터링 잘 맞을까요?

[@rolandgdean]

That's a great thing and I REALLY need to make one small scale to make 10mm dowels about 40mm long. I'm worried about deflection into the blade on diameters that small. I have a tool for making them now but it's a bit rough cut when it's done and I lose too much size sanding them smooth. Also, as always, great video bud. Really top shelf!

[@youtukang]

👍👍

[@j-woodworking9573]

I'm not sure. But if drill checks were applied to the jig what you wanted to would be possible. I will sleep on it and try later. Thanks buddy.

[@samibasti4051]

Beautiful😍😍😍

[@chiokock4057]

정말 고수 시군요..많은 도움이 됩니다..저두 한번 만들어보고 싶은데 혹시 양쪽 베어링(?)은 어디서 구해야 하는지요??

[@chiokock4057]

그리고 내경은 어떻게 되는지요?

[@saxohealer1011]

검색 또는 인터넷 쇼핑몰에 검색하면 다양하게 나와있습니다. "UCFL 베어링"

[@saxohealer1011]

@@chiokock4057 내경은 전산너트 규격에 맞추는 될둣 생각되네요

[@MrCFB80]

Thats awesome, what are those bearings called?

[@집수리마스터-x8p]

새해복 많이 받으세요 ^^^

[@Zie_carpentry]

Hii there

[@j-woodworking9573]

복 많이 받으세요. 감사합니다.

[@vanzipper6486]

you genius 👌👍

[@shin_2_na]

휴..역시..고수시네요...ㅠㅠ

[@jesuinogomes804]

Ótimo gostei😮

[@jairsouza7108]

Como sempre, excelente ! 🇧🇷

[@lee_innovation]

와 너무 멋지십니다~

[@amagautomagassa5445]

Excellent travail

[@jarmstrong2843]

Outstanding!

[@carlosmartini2386]

Parabéns, Ficou ótimo!

[@sueudesrocha9988]

Como se chama essa peça que fica os rolamentos?

[@eballacharles0302]

Awesome 👊👍

Congratulation!

[@Carlos007007ful]

🇧🇷Parabéns 👏👏👏👏👏

[@belarminoskills6007]

Bravo amigo...

[@ИмператорСметаны]

Для дисковой пилы боковые нагрузки не желательны , с таким станком подшипники придут в негодность довольно быстро . А вместо пилы можно использовать стамеску или любой заточенный кусок стали , если нужна точность можно установить её на каретку выставив необходимую высоту и просто гонять вперёд назад . А так ты пытаешься изобрести велосипед заново , но забыв про педали . Удачи !

[@LiveLaughLoveLift]

Amazing! Can you provide the sizes of flange bearings, bolts, screws? Thanks!!!!

[@Ахмед-д5ъ]

НА МНОГО ПРОЩЕ ВСЕ ДЕЛАЕТСЯ! как на токарном станке , смещается задняя бабка, можно в лево право, можно вверх в низ без всяких подкладушек!

[@АлексейМахновец]

При этом токарник конечно же есть в мастерской правильно?

[@j-woodworking9573]

I don't have a lathe. Thanks for watching sir.

[@Simeon_Usherov]

Тут соль в том, что можно делать очень много _одинаковых_ кругляшек без особых замеров, что существенно экономит время. Зарядил палку, прогнал её через настроенную приспособу, и получил заведомо одинаковые результаты, - без дополнительных проверок размеров. Например, кучу ножек для разборных табуреток.

[@albertoferreira9144]

Como faço para comprar?

[@wickedways1291]

Absolutely brilliant

[@hanstenhave3352]

Ingenious!

[@PatriotMango]

where do you buy that blue metal thing? what's it called?

[@AsgardianSikh-pc6zk]

Search for “ball bearing flange unit”

[@antoniocarlosrabachin1355]

Qual nomes das pecas que usa e os tamanhos

[@williamsantos5214]

Wonderful tanks

[@setiawanprojek1539]

Sangat inspiratif friend

[@youtukang]

Siap. 😊👍👍

[@abbas2276]

Thanks for you my friend

[@youtukang]

Salam 🤝🤝

[@irmaodagaioladeusfiel]

Top 👏👏👏👏

[@jaimee.campuzanot.2702]

Thank you sir.

[@VIKTOR-b1e]

Если это обучающее виде,то может и подскажете где эту фурнитуру покупать.

[@j-woodworking9573]

I got them at a local bearing shop here. Thanks for watching sir.

[@guyh.4553]

Cool idea for making dowels but there is no tapering of these at all. Just an FYI

[@jeffforbes3772]

Genius

[@Валерий-ч4ю]

Молодец.голова.

[@dionisiojosedasilvajose2754]

Eu coloquei um vidro no começo englinado para frente de 30 graus não vem po

[@sajidrafique375]

Arigato 😍

[@kairosmarcenaria3791]

Tem como me passar esse projeto por favor preciso muito fazer um desse pramim as medidas eo nome desses parafuso e essa pesa aí que tem 2 iguais por favor tô montando uma marcenaria pramim e o meu ganha pão por favor

[@Carlos007007ful]

👏👏👏👏👏

[@fabiomachado9924]

👍👍👍👏👏👏👏

[@kairosmarcenaria3791]

Ola

[@akinsen23]

Very dangerous sir.

[@русланкырлан-й8о]

Увидел приспособление и своего кота вспомнил

[@thunguyenthi4076]

👍👍👍👍👍🇻🇳🇻🇳🇻🇳🇻🇳

[@Drongo-ol9jf]

Любой сможет?

[@mike8984ify]

Do you have any Pros/Cons versus this design: kzbin.info/www/bejne/f5qTlq2uhLiGbLc I was leaning towards it but wasn't sure if I was missing anything

[@j-woodworking9573]

That is one of the great jigs. Thanks for watching sir.

[@hachmiboualem8339]

Toop Toop

[@coolhead8686]

It is not a perfect diameter throughout.

[@nguyentruongson2420]

Không khoa học.

[@kodman247]

Lathe?