Tecware - Flatline Chassis (The Experience)

[@blexbottt5119]

Hello, can you still put the 2.5 ssd inside the case where it can be also seen, even if you put the front fans also inside the case too just like what you did in 2:42 in the video?? Also, is the front panel metal? and does it have that actual magnetic mesh just likee the top magnetic panel?

[@KleoYan]

Hi BlexBOTTT, welcome to my channel. There is a hard disk cage for you to place your 2.5" SSD even with the front fans attached. The front is metal with holes, there are no mesh filters at the frount.

[@blexbottt5119]

@@KleoYan Hello, and also may I know the dimensions of the front panel fan placements? there has that rounded corners of it, definitely a place for magnetic dust filters there, I will refer to your other video in this timestamp: kzbin.info/www/bejne/hKDSi5qXptd7eas

[@KleoYan]

@@blexbottt5119 Hi, do pardon me as this case no longer with me. I am not able to tell you the demension.

[@xc1774]

How did u manage to screw the bottom fans on the gpu side? What screw did u use?

[@KleoYan]

Hi Mermalaid, welcome to my channel. there are long screws that comes with the case, which is meant for you to mount fans at the bottom below the GPU.

[@xc1774]

@@KleoYan yeah i try to screw it on but it just chipped the paint of my case but cannot screw it in? Did u force it?

[@KleoYan]

@@xc1774 nope I have no issues and I know why you are having this issue. you just plug the fans and screw in.. maybe in future, before you place the fans and to screw it down. Do this.. use a screw, screw on those hole. 1 turn clockwise and 1.2 turn anti-clockwise. As why doing this.. due to the fact that the case is power coated, therefore the threads on the hole will be filled, causing screws hard to screw in.. as why the motion on the screws, when you perform anti clockwise, the residue that stuck on the actual screws will off. This will make screwing the whole screw easier. Once you have done this to all the screw holes in the case.. it will be easier to place the fans and to screw it in place.

[@HockOoiOng]

Thank you for this video! do you remember what is your ambient temp?

[@KleoYan]

Hello Hock Ooi, welcome to my channel, yes, the ambient of my room is at 29 degrees without aircon. this unit was completed at night.

[@prawnstars3160]

thanks! really like your clean cable management

[@KleoYan]

Hi prawnStars, welcome to my channel and thank you for your valuable feedback. All the best with your build too. 😉

[@rovs2706]

Hello! What fans did you use on this video? That one with white inside? Also is there a red version for that fan?

[@KleoYan]

@@rovs2706 hi welcome to my channel. They are the Arctic bionix p120 fans and yes they have it in red

[@rovs2706]

@@KleoYan just searched it and it's too expensive here in the Philippines and on Ebay or amazon. Its 1300 php/ 23 usd. Damnnnnn. Anyways thanks brooo keep up the vids and nice build, looks neat

[@KleoYan]

@@rovs2706 thank you.. all the best with your build too.

[@rave5558]

Hi! Very nice video. However I am still unsure how to mount an SSD there. Are you able to show a demo, on how to install an SSD on that case?

[@KleoYan]

Hi Raeven Bagtas, welcome to my channel. So pardon me as this pc is no longer with me. Therefore I can show you on this, but I do have another video which shows you an over view of this case kzbin.info/www/bejne/hKDSi5qXptd7eas so pardon me. Once again thank you for your visit.

[@dthanos4903]

I’m planning to get this case but i’m concerned if large air coolers like Deepcool Ak620 or thermalight peerless assassin will fit on this case? And also if my current ram sticks will comparible with the said coolers( corsair vengence pro rgb)

[@KleoYan]

Hi @dthanos4903, welcome to my channel , Tthe height of the aircooler in this video is at 156mm tall. To be honest, it's not advisable to use this case with the AK620, the height of the AK620 is 160mm and this case aircooler height is at 160mm too, you might have an issue to close the side panel. www.tecware.co/flatline

[@nelvc7014]

Hey, just wanted to ask a qn, if im using a dual tower cpu cooler, it looks like the tower would contact with the one fan to the left?

[@KleoYan]

Hi nelvc, welcome to my channel. You can adjust the fan positioning or if on the right where your rams are allocated, so long there are space and the height of your rams are not too high. Then you will be able to plug it to the right.

[@nelvc7014]

@@KleoYan hey thanks for the reply, i also noticed your bottom fans under the gpu. They are set to blow air to the gpu right? I was thinking to use this exact same configuration as i thought the airflow was really nice with no dead zones as the front intake fans could get air stuck under the gpu. however does this not starve the psu's intake fan directly under? also just gonna ask if u already hv done a temp benchmark ? thanks

[@KleoYan]

@@nelvc7014 hi, this system is build for a friend. I can only recall that the temp for cpu is not over 84degrees and for the GPU after undervolt the temp max is at 76 and the hotspot is around 80s not more than 86.

[@azublu043]

Tecware Flatline, Tecware Forge M, or Montech Air 100 argb/lite?? Which do you think is the better case here in terms of cost efficiency, effectiveness in airflow, build, etc.

[@KleoYan]

Hi 【나이스】 welcome to my channel, I have not tested on tecware Forge M case before but to me, I will go for Montech Air 100 Lite, even compared to this Flatline. it just gives a premium feel on the Montech Air 100 Lite. kzbin.info/www/bejne/gYDYiGurps6iqtE

[@KleoYan]

I think this will aid you further in your decision kzbin.info/aero/PLEW-b-2vYDdN95yTw9wmAo_iwvr_t7Md-

[@azublu043]

@@KleoYan THANK YOU!! Really fast reply that you made it in time before my voucher expires. With that, I subbed and liked as its the least I can do!

[@KleoYan]

@@azublu043 you are most welcome and all the best with your build too. Thank you to have visit.

[@bernreccion]

Hi, how did you connect all those fans? did you connect them all to the mobo or you used a fan hub?

[@KleoYan]

Hi Bernard Reccion, I have pair them up in daisy chained and plug directly to the motherboard. 2 set of fans to one fan harder to distribute the load.

[@bernreccion]

@@KleoYan thanks man, love your content!

[@KleoYan]

@@bernreccion you are most welcome and all the best with your build.

[@eino331]

is there a clearance between the top of cpu cooler and the tempered glass?

[@KleoYan]

Hi eino, welcome to my channel. So long your air cooler is not 168mm at height, you will have enough clearance to mount the side panel without any issues.

[@rainbowbubble456]

This case is what I'm seeking for! smaller than montech air 100 and better design (in my opinion) I want to know if front panel can be removed easily or not.

[@KleoYan]

Hello Jui-Chang Hu, welcome to my channel. The front bezel needs abit of strength to removed. instead of pulling at the bottom. I did the four corners which I have shown you in this video as I feel that I could break the front bezel if I pull it from it's intended location, which is from the bottom hole.

[@Jsonville9]

Is it possible to put a DIY dust filter in front? Since the fans are not installed in front but at the back of the steel (for in take). Thanks

[@KleoYan]

Hi Jason, welcome to my channel. Yup you can do that. 😉

[@djbbybnz4444]

Do you think this have better thermals than the NZXT H510 Flow? I'm considering this case but I really like the aesthetics of the H510 series.

[@KleoYan]

Hi djbbybnz, welcome to my channel. I can’t answer you as I have not tested temperature on the H510 case. The only thing I can tell you is, NZXT H510 should have a better build quality.

[@djbbybnz4444]

Thanks for the response!

[@KleoYan]

@@djbbybnz4444 you are most welcome and all the very best with your build.

[@kylemillonte7322]

why didnt u lower the rear exhaust fan all the way to line up with the heatsink?

[@KleoYan]

Hi Kyle Millonte, welcome to my channel. In this video I didn’t but before sending this off, I did ☺️. As you are right to have it align with the cpu fans. Thank you for the pointer and to have visited my channel.

[@kylemillonte7322]

@@KleoYan ye thanks bro was planning to buy this case nobody else does that aligning the rear exhaust to the heatsink its just so satisfying

[@KleoYan]

@@kylemillonte7322 ooo I see, thats good and yup very satisfying, btw all the very best with your build 👍

[@benhaymin6913]

Hii nice clean build, may i know what are those PC fans that u used for this build

[@KleoYan]

Hi Benhaymin, welcome to my channel, those are Arctic Bionix P120 and P140 fans. which comes with various color linings. www.arctic.de/en/BioniX-P120/ACFAN00168A

[@ana-xw4zr]

bottom fans are intake or exhaust? It is better to add bottom fans? wouldnt it create more problems, like making it as intake PSU heat will be transfered to GPU & as exhaust vaccumizing the GPU intake?

[@KleoYan]

Hi Ara, welcome to my channel. the fans are both intake and in this setup, the PSU does not really heat up. So it's perfectly fine in my case.

[@winchteodoro]

@@KleoYan I also have this case. Is it okay if I place the bottoms fans as exhaust? Or intake is the best setup for this case regarding the bottom fans?

[@KleoYan]

@@winchteodoro hi Ninyo Teodoro, welcome to my channel. If you have a GPU mounted to your motherboard, it is not advsiable to do exchuast. you might damage the fan due to opposite direction. As your graphics card fans are trying to draw air to the heatsink.

[@winchteodoro]

@@KleoYan So I should place it as Intake instead?

[@KleoYan]

@@winchteodoro yes if the gpu is how I have mentioned to you earlier.

[@BatteryAz1z]

Looks very similar to a meshify C mini in terms of layout. Clean build!

[@KleoYan]

welcome to my channel BAtteryAzi. Infact most cases look alike with the interior but the exterior may vary. Nevertheless this case cost much lesser compared to the Meshify C Mini. thank you for visiting and to leave your valuable feedback. 👍

[@BatteryAz1z]

@@KleoYan been subscribed for a while, just now commenting. I like your videos, no-nonsense and always with some practical insight that other channels don't talk about. Keep it up.

[@KleoYan]

@@BatteryAz1z I see, thank you for the feedback , greatly appreciated it. If you do have suggestion for me to improve my content, do let me know, I will see what I can do to improve. Once again thank you,

[@wicrom]

Hello, this video has been very helpful! Will a 240mm AIO water cooler fit at the top?

[@KleoYan]

Hi mazipan, welcome to my channel. It will so long your radiator is not 38mm thick. 27mm thick will do and best to mount with Low profile rams too. This will prevent incompatibilities.

[@wicrom]

@@KleoYan thank you so much for the prompt and informative reply! You earned a sub!

[@KleoYan]

@@wicrom hi. you are most welcome and all the best with your build too 🙂

[@jonsuuuuuu]

Hi. i just bought the same case yesterday, Is the stock fan of Tecware noisy for you? In my case, it's noisy.

[@KleoYan]

Hi Caley Jones Dacquil, welcome to my channel. For noise, it depends on individual, for me I am use to it. if you feel it's noisy you can always go to your motherboard UEFI to tune it down. using DC mode as the case fans are all 3pin. This video will aid you someways on how to set your fan to DC mode and to use voltage to control the RPM of the tecware flatline fans. kzbin.info/www/bejne/g3SwnKWHrKuhga8si=R7qYyXWHKXlR3uI5

[@sjneow]

Why do you have the cpu fan in pull though?

[@KleoYan]

Hi Sjneow, welcome to my channel. For mid end processor. I have tested, Be it pull or push it doesn’t impact the thermal that much. Plus I do undervolting to sustain the performance at default clock speed and the main reason for a pull configuration, less dust will accumulate on the fin stack, therefor making cleaning easier. Hope this answer your question

[@elusiveinstinct]

does this case has fanhub?

[@KleoYan]

Hi Elusive Instinct, welcome to my channel. Nope, it does not come with a fan hub.

[@josephventura1477]

I currently have this case. Do you think that a Noctua DH15 would fit?

[@KleoYan]

Hi Joseph Ventura, welcome to my channel. The height clearance of this case is at 160mm and the DH15 is also at 160mm. I do not have a DH15 but based on the measurements. I personally will not fit the DH15 to this case, you might not be able to close the Tempered glass panel properly. The choice is yours.

[@josephventura1477]

Do you think that it can support vertical gpu mount?

[@KleoYan]

@@josephventura1477 hi welcome back. I don’t think is a good idea to have vertical mount as the PCIe slots are not totally empty when you remove them. If you choose to go vertical mount. You might need to cut out the PCIe slot pillars, as you need to pass through either the hdmi or DP connectors. Or you can get the cooler master v2 gpu mount which does allow you to extend the bracket, but the length will not fit a GPU that is 320mm in length. Most it will go is 280mm in length.

[@josephventura1477]

Thank you

[@KleoYan]

@@josephventura1477 you are most welcome. All the best with your build. 👍

[@Ryoyenata]

I have 2x140mm thats 30mm thick, can i put it as intake?

[@KleoYan]

Hi Ryo yenata, welcome to my channel and it will fit, just need to move the top fans abit to the rear to give more clearance at the front (for your 2 x 140 x 3mm fans)

[@skyezer1497]

Are those stock case fans or did you buy them elsewhere? Might want to know the name of those if you can share :)

[@KleoYan]

Hi Skywest, welcome to my channel, the bottom fans are provided with the case. The rest are from Arctic. Top - Arctic Bionix F140 Front - Arctic Bionix P140 Rear - Arctic Bionix F120.

[@skyezer1497]

@@KleoYan Thanks man!

[@KleoYan]

@@skyezer1497 you are most welcome 👍

[@apeklagendari]

sir..can u put the link where can i but that remote start.?

[@KleoYan]

Hello apek lagendari, welcome to my channel. Here you go SG$ 11.12 20％ Off | PCI-E Desktop PC Remote Controller 20m Wireless Restart Switch Turn On Off Drop Shipping a.aliexpress.com/_mOw2oBG

[@yersinja]

Very good content sir. May I ask if it would be better to add 2 exhaust fans at the top or 2 below the gpu? I plan on using the 4 stock fans as it is. I'm using the AK400 for my 12400F and the 3 fan 3060TI vision. Thank you.

[@KleoYan]

Hi MJ, welcome to my channel, the fan arrangement of this video are as follow. Front - 2 x 140mm fans intake Top - 2 x 140mm fans exhaust Bottom - 2 x 120mm fans intake Rear - 1 x 120mm exhaust I did change the orientation on the Top to be intake and the rest as configured above. I gotten better results just to change the top fans from exhuast to intake.

[@chrisrafel]

@@KleoYan are the fans 4pin? Thanks

[@KleoYan]

@@chrisrafel hello welcome back. Nope the case fans are not pwm, they are 3pin

[@miadu2466]

@@KleoYanregarding on you saying you changed the Top fans to intake, so that means you only have one exhaust fan? Did it provide better cooling?

[@KleoYan]

@@miadu2466 Hi welcome to my channel. I woulld advise if you are using Aircooling, do not install top fans. just depend on the front intake and bottom intake.. exhaust through the rear and naturally to the top.That will be more ideal.

[@imsadidontcare9537]

B550 aorus master suit this case?

[@KleoYan]

Hi i’m sad I don’t care, welcome to my channel if that is not a m-atx motherboard, no and your motherboard is an ATX motherboard.

[@paisenpaisen]

Hi, i'm actually planning to buy this case and I got a question about the stock fans. Are they noisy and go at full speed, or can the rpm be controlled by the fan hub + mobo software? Great vid btw, one of the only in depth vids about this case I've seen on YT

[@KleoYan]

Hi Gavin, welcome to my channel. It greatly depends on individual to define noise. You can always control these fans through the motherboard. Just dc mode and set the fan profile. Let me grab another video as why I suggest you to use dc mode.

[@KleoYan]

OK Gavin.. Watch this video as I did explain what's the different between pwm or dc mode. kzbin.info/www/bejne/g3SwnKWHrKuhga8 hope this will help you out. By the way, thanks for the compliment and all the best with your new build..

[@paisenpaisen]

@@KleoYan seems that you've gotten this exact question a lot that you even made a vid lol. your vid really helped thanks man

[@KleoYan]

@@paisenpaisen you are most welcome. 👍

[@ayhvd1176]

hi, will a 335 mm gpu fit in here? MSI SUPRIM X

[@KleoYan]

Hello ayhvd, welcome to my channel. Though specs for this case is stated 340mm gpu length clearance but after you have place the front fans. It might limit to 315mm

[@ayhvd1176]

@@KleoYan hi, i actually did some diy and did manage to put the gpu in the case, tight fitting but it fits well!

[@KleoYan]

@@ayhvd1176 nice, am curious what you did to make it work? Got to learn something from you 😉

[@ayhvd1176]

@@KleoYan oh no you wouldn't like it... had to bend some stuff to get it in haha

[@KleoYan]

@@ayhvd1176 oh Okok thanks for replying.

[@jcjam-2.0]

Ty!

[@KleoYan]

Hello JC, welcome to my channel and you are most welcome.

[@shiina0232]

the lrice of the motherboard could have get a x570 in singapore

[@KleoYan]

Hello Shiina02, welcome back, the whole unit of this setup only cost lower than 1K, infact this pc is for charity. a group of friends have donated. so ya.. thanks for the feedback.