Check out the other videos of the PWK 24mm and an unboxing of Nibbi's Carbs and Features! kzbin.info/www/bejne/qnK6m4WErrSFrJo kzbin.info/www/bejne/lYKYq6mqlJWZf68
@ProDigit80Ай бұрын
110-125cc needs an 18-22mm. No need for a 24mm. 150cc needs a 24-28mm. No need for a 30mm. Speed womt magically be higher if you have a too large carburetor.
@mikesmotoshop Жыл бұрын
Carb looks super good quality!
@bearkreekboys Жыл бұрын
It is!
@Mroswaldo163 ай бұрын
I have a nibbi 22mm, with a 26mm manifold. Engine would run anymore. Need tuning badly. I might have to go down on jet size & start from the bottom. It starts fine with the pz19
@SpAcEcruizer20325 күн бұрын
The stock manifold is 26mm I believe
@taitheguy8511 ай бұрын
Really confusing. You say bigger carbs don't work as well. Title says "best" carb - PE22. Then you say the pe24 flange works best? So, not the PE24? Just the PE22 with the 24mm flange? Or..?
@bearkreekboys11 ай бұрын
PE22 is best, it takes a lot more trial and error with the bigger carburetor (PE24).
@SpAcEcruizer20325 күн бұрын
So u put oring to oring or vice versa another thing does a plastic spacer go on the other side of the manifold or just the green paper gasket
@bearkreekboys24 күн бұрын
Plastic spacer is gasket seal to intake, o ring at carb seals that side.
@crabrangoon24933 ай бұрын
Hey do you think i should get a 19mm or 22mm because originaly i have a 19mm one
@bearkreekboys3 ай бұрын
What engine?
@crabrangoon24933 ай бұрын
@@bearkreekboys110cc
@bearkreekboys3 ай бұрын
@@crabrangoon2493 you can do a 19mm one, the 22 required some jetting to make it responsive
@evan_the_bum16723 ай бұрын
Same here just got a ssr 110cc, stock carb is a 19mm I believe so should i just go with a 19mm nibbi ? Thanks ! @bearkreekboys
@MikeMik863 ай бұрын
Introducing your friend valve float with a larger carb, be carful or you'll make some valve to piston love at high RPM
@MikeMik863 ай бұрын
The power till top end would still be better given you open up the exhaust and intake
@brandonbassett71252 ай бұрын
So I got a ssr 110cc stock. Which comes with factory 16mm carb. So if I do a 22mm carb I will not need to do jets or tune? Just bolt on
@bearkreekboys2 ай бұрын
You will probably have to do some tuning, they usually will run out of the box but for best performance some adjustments are needed
@golightly209Ай бұрын
I have a 110 rfz apollo I see a lot of videos saying swap out the carb. What size do I need.
@bearkreekboysАй бұрын
22mm nibbi
@TurboegАй бұрын
Can I use the PE22 with stock intake neck?
@bearkreekboysАй бұрын
Yea!
@TurboegАй бұрын
@@bearkreekboys thanks for the fast reply! Just picked up a 125cc and needs a new carb. So I have one on the way
@geritomlet25248 ай бұрын
On my coolster 125 the carb hits the engine cooling fins. Also the stock manifold is not 22 is there an adapter manifold out there?
@bearkreekboys8 ай бұрын
May need a different manifold
@cilami Жыл бұрын
Very useful video. Thanks for posting. Performance wise, how the nibbi compares with the stock? I am thinking about installing a Nibbi 22 mm in my SSR 110, but some people online are having problems getting them tuned/working properly (in low and high gears)?. Would a Mukini be a better option? I will be waiting for the next videos, for sure 👍🏻
@bearkreekboys Жыл бұрын
It all comes down to jetting and what type of riding your doing. I'll have some tuning videos on this setup for sure. Main thing is getting nibbi's actual jet kit for the mains and pilots. They have so many sizes. You almost have to get the pilot circuit as rich as possible without making it so choppy. Then getting main jet to pull all the way out and not fall on it's face. I think the Nibbi is way snappier and revs faster than any of the mikunis. We had the Chinese mikuni and stock carbs and nibbi is the best for quick rev and pull on top end. They r similar to a Keihin carb like what's used on the smaller 125 dirt bikes back in the day.
@michaelneville439311 ай бұрын
I have the nibbi pe 22 on a 110 and if I blip the throttle quick it bogs to stall. If I slowly accelerate it's fine. Tried different pilots and still no change. High revs seem ok just that quick blip bogs bad with 30-38 pilots and air screw tried for rich and lean😢
@RADscouter6 ай бұрын
Do i have to put on that specific air filter? Can i just fit a UNI foam filter?
@bearkreekboys6 ай бұрын
As long as it fits!
@joeshiesty42168 ай бұрын
I got a 26mm one for my rfz 125 and it seems too big for the intake, been looking for some kinda adapter if I can, or just get a 24mm carb instead??
@bearkreekboys8 ай бұрын
Watch my other videos you want a 22 mm
@DanielS7847 ай бұрын
I bought the carburetor and the air filter. I am thinking about sending the carburetor back because my neighbor said the stock carburetor should work fine. What are the benefits of putting on a new carburetor? Also looking at the stock air filter there is a hose that runs into it. I don't see any place for a hose to go on the nubbi filter so I am not sure how to out on the new one.
@bearkreekboys7 ай бұрын
When you get the Navy tuned correctly the snappiness of it is much nicer than stock. It revs faster and gets up to speed quicker. That hose is most likely a crankcase breather hose that comes off the engine into the air cleaner certain Chinese bikes have that
@DanielS7847 ай бұрын
@@bearkreekboys do you think it would cause a problem if I installed the Nubbi air filter and didn't connect the hose that went to the stock filter?
@DillonWaffles7 ай бұрын
@@DanielS784you’ll just want to add a filter to the hose coming out of the valve cover. I’m assuming you’re working on a gx200 or a generic 196cc. They make valve covers tapped for a hose and filter. Or you can rig a filter to the existing hose.
@tizzor Жыл бұрын
with mine i have to let it warm up run it up and down the street to get it idling good and no bog do you think i could go maybe for a smaller pilot jet cause i looked at the original jet and its so much smaller than the nibbis but hey i aint complaining i couldn’t get the bike running for 2 months cause the original carburetor broke and the replica mikuni didnt run well. thanks!
@bearkreekboys Жыл бұрын
The size of the hole in the jet has nothing to do with fuel amount being put through it it's all flow rates of those Jets so there's certain little changes in the design of the hole drilled in it that make it bigger or smaller jet number
@bearkreekboys Жыл бұрын
You want to go is Rich on the pilot as you can and tell you start sputtering rich and you'll know what I'm talking about cuz it'll sound Goofy but you want to be as rich as you can so that you could good throttle esponse and you get good cold start at idle operation
@zancudo77978 ай бұрын
My 125c sputters quite alot and recently when i turn my fuel on it just comes pouring out
@bearkreekboys8 ай бұрын
Your float is not sealing or the float height is way too high
@zancudo77978 ай бұрын
@bearkreekboys thanks is a 22 carb the best bet for 125 I believe I have a smaller one and feel like it's popping and backfiring instead of giving power
@adriel93549 ай бұрын
What is the inner diameter of your intake manifold
@bearkreekboys9 ай бұрын
I'll have to measure again
@robmuhfacka5986 Жыл бұрын
I have a larger 125 pit bike the Xpro X6 and it comes with a jingke 26mm but I'm wanting to put maybe a 24mm flange nibbi?
@bearkreekboys Жыл бұрын
It would probably work decently for you! How does the bike run right now with that carb
@robmuhfacka5986 Жыл бұрын
So I went ahead and got the 22mm flange even though the bike is a little larger than pitbike size. Right now stock it runs okay but definitely not peppy or high revving it barely sounds like a dirtbike more like a small 125cc motorcycle lol its slow too it builds speed pretty well but doesn't have any real pep to its step. 1st gear is super short and second gear you pick up good speed but there's no real torque. I'm looking to make it into a wheelie machine so I'm doing the 22mm carb and a 13t sprocket up front. If need be depending on how short first and second becomes I may go with a larger rear sprocket also 👌
@cakedaddy153110 ай бұрын
@@robmuhfacka5986what did you find out? How’s it running?
@5.0mlp314 ай бұрын
Yamaha TTR 125 will it fit?
@bearkreekboys4 ай бұрын
You would need to check the bolt pattern spacing and the air filter diameter
@wisemrstrange19584 ай бұрын
will this fit on my 2018 ttr110?
@bearkreekboys4 ай бұрын
If the bolt pattern fits I would say yes
@andrewjensen503311 ай бұрын
Hi, I got a pit bike with this Carb, and I can't get it running. I have spark, 75 psi compression when kicked, and fuel looks pretty good. I've also looked at timing, and that looks correct... What should I do? Thanks!
@bearkreekboys11 ай бұрын
Valves in spec? Is the fuel fresh? Is there a new spark plug in it? Has the carb been taken apart and checked?
@andrewjensen503311 ай бұрын
I did some more research this afternoon, and looks like I actually adjusted the valves to 0.04" instead of 0.04mm. 🤦♂️ Otherwise, it's a new spark, new fuel, and the carb's brand new, because the bike didn't have one when I got it. I'll readjust valves and get back to you 👍
@andrewjensen503311 ай бұрын
I went to readjust the valves, and the exhaust valve is stuck closed, any recommendations?
@bearkreekboys11 ай бұрын
what do u mean closed as in the valve doesnt move at all? or ?@@andrewjensen5033
@bearkreekboys11 ай бұрын
should be .004"@@andrewjensen5033
@Jordxn.5 ай бұрын
My dirt bike has a tube attached to its carb air filter, when I replace the carb, must I get an air filter that connects the tube to the back?
@bearkreekboys5 ай бұрын
I would just re route that breather somewhere else. Or buy a filter filter for the end of that tube and tie it up to the frame. That's a crankcase vent breather and just goes to atmosphere do not plug, just find a spot so it won't get mud water dirt in.
@realztv36256 ай бұрын
Just put the same one on mine, is there a way to fix the lag right away when u quickly hit the throttle?
@bearkreekboys6 ай бұрын
Richen up the pilot yet and play with your air screw
@DanielS7847 ай бұрын
@bearkreekboys do you think it would cause a problem if I installed the Nubbi air filter and didn't connect the hose that went to the stock filter?
@bearkreekboys7 ай бұрын
No just tuck it away in the frame area, do not block it though. A place where water and dirt can't get in easily is best
@DanielS7847 ай бұрын
@@bearkreekboys Do think a zip tie would work good?
@nektar43353 ай бұрын
my pitbike wont start with air closed whats the problem
@bearkreekboys3 ай бұрын
Can u explain?
@nektar43353 ай бұрын
@@bearkreekboys so when i turn it on i open the air then when i close the air bike shuts off and wont start unless air is open
@crabrangoon24933 ай бұрын
@@nektar4335so it just runs when choke is on?
@catalinnicolaevici206111 ай бұрын
Thanks for the heads up i just bought one off some dude for 200$ and my buddy said the carburetors suck ass on them then after a few video i said F it and ponyed up the 60$ for a carburetor also it needed some new parts like the magneto cover and definitely new wiring cause some crackhead looks like they stuck there nose in it. But i wanted it to pull my 200lbs fatass around on it in the woods😂😂. Got that exact carb you have any tips on it? To do not to do
@bearkreekboys11 ай бұрын
See how it is out of the box. Install it and run it. See how idle and throttle response are. Take it for a ride and see if the wide open is okay or it it bogs down or sputters. Comment on here with ur findings, I found I had to richen up the pilot for sure and also richen the needle clip if it's not at 4th position already. Let me know if u need any more help