The Best ESC for $10

[@mauricioaraya4359]

Hi, do you know what the switch is for on the board???

[@gabrielsilvaz4199]

Mauricio Araya That’s very good question I was meaning to make a video on that. originally it was advertised to not have brakes but it does that’s it activates your breaks on one position when you turned it on it will beep once then twice and when you switch it to the other side it will do the same but in a different tone! one tone will sound quite pleasant and the other one will sound doll and boring I think you’ll know what I mean when you hear it. The doll and boring tone is your brakes. You actually reminded me I need to make a video on that because there are videos on these ESC‘s and guys claims that the one ESC with some certain chip in the center is the break. If you see one without the chip it has no brakes but that is not true that switch activate your brakes or deactivates it. thanks for reminding me😅

[@gabrielsilvaz4199]

Mauricio Araya I pinned your comment because it was very important question!

[@glowworm3345]

Gabriel Silvaz I’m getting the same beep tone whichever way the switch is pressed, and I’m having no luck getting the drag brake function to work.

[@rahulpandit1749]

Actually...the smaller esc is also 3s capable....I used it on a crawler(temporary replacement) with a cooling fan...and it worked fine on 20c 3s...the main problem is. The bec output...it doesnt give enough power to the servos...had to hook up an external battery to the vcc channel to power the servo and reciever...and cut off the live wire coming from the esc to prevent overvoltage

[@CarlosTorres-bh6um]

where do you buy them which internet site do you buy them

[@benjellesed7716]

I have the second ESC that you review and its not bad i have it plugged into my scx24 stock v2 ESC and it acts as my ESC and the stock is just a receiver for my remote. I am now having problems with one rig Binding to my remote, I can get the wheels to turn up front but it wont drive forward or backwards.

[@bromleysmakeityourselfrc2853]

Awesome vid! Was looking at this esc and thought it was too big... now I’m getting it! Also I found a new bright Jeep at the thrift shop...doing the build soon based on your truck!

[@wheelbarrow2803]

Can you program this ESC? I saw on the AliExpress listing that the seller mentioned "ESC is set in the middle of the range, the new control generally need to fine tune the throttle."

[@blackdawgrc8425]

Cool video! Can I use a rc4wd winch???

[@ndbapereira]

I had a very bad expirience with the "Double way 320A", the ESC died but still flashes the red led and power the receiver. At the same time, motor does not move and the battery looks almost short, the ESC is pushing extremly high currents. High current is pushed from the battery independent of what you do in the controller (you can even disconnect the receiver, high current will flow from the battery and the battery, cables and ESC get very hot). The ESC worked for 3 runs, about 40min total and was good when it worked but honestly, with this behavior I won't considering only bad, it's actualy very dandgerous

[@gabrielsilvaz4199]

Oh, I’m sorry to hear you had a bad experience. I’ve literally had dozens of these and never had one issue. I also use triple capacitors configurations on my motors which remedy is a lot of issues that most ESC May have. I’m not sure exactly how you are wiring up your systems, but if you dive deeper into my channel, you can find some of the methods that I’ve used with great success. I’ve never had my ESC overheat or any of my batteries.

[@RunThatRC]

I am hooked on the wpl stuff lately. Nice vids by the way just subbed! Have a great day and RunThatRc!

[@financialloser]

RunThatRC Bruh found ya

[@modelnutty6503]

near same size and price as the 10A, are 20A with brake and reverse. I've used a couple in small brushed motor planes, with a big fat diode in line so reverse can't ever happen!

[@summersong88]

Hi Gabriel, do you have a video where you install the 320A in a C24? I want to get that one but I’m worried it might be too big. I want to build a scale look C24 so I prefer to not have a big ESC on the pickup bed 😀 any suggestions you can share will be appreciated. Thanks!

[@1australianbeacon]

Hi how is this connected the smaller one especially. As I have a foam plane that I blew the reciever pcb and was thinking of getting a new controller what do I need. Cheers

[@roadstar499]

what about the 2 red pins... i am running 2s lipo i want forward brakes and reverse...np mention of the pins and thats what everyone needs to know...thanks

[@christiansrcs7789]

Does that 2 esc the small one have lipo cut off??

[@brianmason8597]

hi I bought one of the small 10a esc's for the bow thruster on my tug. Mine came with no instructions at all. Before I connect up I would like to check which of the leads is for the battery and which for the motor? I assume the female pluf is for the battery and the male the motor.

[@gabrielsilvaz4199]

That’s correct..!! these ESC’s don’t come with instructions. Also the little switch is your brakes on and off

[@brianmason8597]

Hi Thanks for the prompt reply. Things have changed since I was into R/C in the 1980's. Now that I've retired and have started building a scale tug and the electronics are a whole new thing to learn. Any objection to me contacting you occasionally for advice?

[@gabrielsilvaz4199]

😉🤙🤙

[@joeljoel12428]

Hi, I bouth the cheaper esc you show (2nd one) it doesn't work with 8V it work only with 5.5v that's mean that my esc is damaged?

[@rcericon710]

Hey bro, great video! I want to upgrade my esc on my MN D90 what woul you recommend you have two ESC on your videos. 860 and 1060. What’s the difference between the two? Also I recently purchased the two speed gearbox for my D90 what type of motor would you recommend for an upgrade? I don’t care so much as speed. I care about torque Thank you

[@gabrielsilvaz4199]

Rc Erico Artist I would recommend you use the hobby wing 1060 with a 370 single speed Gearbox if torque is what you’re after. The 860 might be hard to fit it in because it is kind of big.

[@financialloser]

Gabriel Silvaz great. Thinking of using this set up on my WPL B24 project. So glad I scrolled. It’s crazy the information I find within the hobby community

[@claudeboyer7655]

bonjour marche avant et moins rapide que la marche arrière que faire

[@RevolutionX]

You have any idea if the smaller esc has a low voltage cutoff for LiPo? I bought the small 30A one, but I'm not sure if there's a low voltage cutoff or if I need to buy a LiPo alarm.

[@gabrielsilvaz4199]

REVolutionX No it doesn’t I always use a voltage meter with a programmable alarm

[@gabrielsilvaz4199]

I bought a bunch of alarms back when they were two dollars

[@RevolutionX]

@@gabrielsilvaz4199 Thanks! I guess I need to buy LiPo alarms now.

[@gabrielsilvaz4199]

REVolutionX Yep and also the little switch is your brake on and off just in case you’re not aware of that😉

[@RevolutionX]

@@gabrielsilvaz4199 Yep, thanks!

[@nhansme]

Thanks for the video. Bought this esc(cheap 20A one)for a wpl b24 and jjrc q60. Do you know how to connect the lights with this esc ?

[@gabrielsilvaz4199]

Hansaka Nakulugamage Sorry for taking so long to reply didn’t realize how many messages I’ve missed. In order to Connect the lights you need to connect the lights not to the ESC but to the receiver just like you would plug-in you servo to the receiver your ESC to the receiver and then on channel 3 you can plug-in lights.

[@nhansme]

Gabriel Silvaz Thank you !!!

[@skykalaicreations]

Hi bro...can we connect the 2 × RS 775 motor in single ESC bro..it is work or not ...is this cause any damage of a esc

[@mpkhobbyRC]

This might be a dumb question but on the little one, what cable gos to the battery?

[@gabrielsilvaz4199]

The female JST connector

[@ernsteliden6719]

Hey. I have both of those esc, or at least the bigger 320A. The smaller 10A I'm not certain is the same, since there are quite a few semi equal. But my question to you is, do you know if they (the smaller) should be calibrated, or if it is even possible. And if so, how this is done? Thanks for a very good video btw.👍👍

[@gabrielsilvaz4199]

Ernste Lidén Calibrated??? Calibrated for what..?? Sorry I’m a hobbyist not an MIT guy🤣😊

[@ernsteliden6719]

@@gabrielsilvaz4199 Lol.. well I'm certainly no MIT guy..😋 Okay Well, some esc apparently needs calibration. I thought after your video that maybe you knew how/if that's done on these guys.😊 I put in the little 10A in the MZ ural, but I feel it is very hard to go slow with. It's like it starts at 1/4 throttle...😳 Thanks for a great video.👍👍

[@gabrielsilvaz4199]

Ernste Lidén Sounds like you need to turn up your dual rate on your transmitter and you’re not gonna go slow with that truck, it’s like second gear in the WPL 2 speed transmission. Do you remember the video of my extreme Land Rover the red one? that one is using that Exact 10 amp ESC in the video also the turbo racing transmitter. There’s a couple videos were people are confused with the dual rate thinking that turning it down helps you crawl slower but it cuts out the power so if you turn up the rate all the way you’ll be able to crawl slower than turning it down. So if there’s any programming you need to do it’s in your transmitter. There are other things other than dual rate on more expensive controllers but not sure which transmitter you’re using?

[@gabrielsilvaz4199]

And remember that LanRover is in low gear🧐

[@ernsteliden6719]

@@gabrielsilvaz4199 Thanks for your answer, and I'll try that. I haven't got the turbo racing controller yet, so I've set it up with my flysky gt3c. It's not as smooth as it was with the stock radio system which is kind of disappointing.. But as the stock hear are cooked what to do..😜 Thanks again my friend that are helpful tips.👍👍

[@johnconrad5487]

3S=== cant take more than 380 motor! etc. what does this mean? It means that the 320A is the name and not the capability of the ECS. It is not 320 AMPS!!! it is a fake name given to it by the Chinese vendors.

[@Rudimaximus]

For small esc bord : can u tell me wich position îs for brake on?

[@SRCE2070]

Do these small 10amp esc's have a drag brake? Is that what the switch is for?

[@gabrielsilvaz4199]

Dave King yes they do. I used to think the switch was for nickel metal hydride batteries and Lipo batteries but it’s The brake on and off switch

[@SRCE2070]

@@gabrielsilvaz4199 Thanks again!

[@itsmee0073]

Could you use a 550 motor with a nihm?

[@apriliafan28]

I got the same ESC, is it normal that it is getting hot/warm ? Its hooked on a 6 volt 700 mah battery. It is from a wpl 2 speed gearbox for a b16.

[@gabrielsilvaz4199]

Yes it is completely normal for the ESC to get Hot/warm that is a good indicator that the ESC is working properly

[@aurelius2100]

We have the same rig i have b16 too

[@aurelius2100]

Can i use 30a esc to my wpl b16 and what motor should i use?

[@carloshnunez]

Hi ¿where did you get the fifth Wheel on that truck?

[@gabrielsilvaz4199]

eBay

[@omkarkhade4602]

Can I connect brushed Johnson RS775 motors with the 320A esc..?

[@gabrielsilvaz4199]

Omkar Khade I’m not familiar with that motor but if it’s bigger than a 540 then Probably not this is a brushed ESC 540 would be the max motor size you can use thanks for commenting

[@omkarkhade4602]

@@gabrielsilvaz4199 okay

[@deluxefarming03]

Which ESC is best for RC Dumper Truck.

[@gabrielsilvaz4199]

It doesn’t really matter both will work great. Depending on how much power you want to put in your truck will be you’re number one priority. I give you all the specs in the video the choice is yours thanks for watching

[@1-2-3rc6]

Great video😎

[@ziaulfakri]

Kalau ESC nya kebakar pengaruh ke recaiver gak om

[@fathanliem7807]

Who is best? 320A or 10A ??

[@gabrielsilvaz4199]

[RDM]Gaming ID in the video I tell you that the 320 is the best that it’s my favorite one to use several times I mention it. because it’s 3s capable and water proof and you can find them on eBay for $6 USA 🇺🇸

[@rcdronesandmore6336]

Can you use plasti-dip on the smaller esc to waterproof ?

[@gabrielsilvaz4199]

RC Crawlers Sure you can but it’s still not 3S Lipo Capable

[@rcdronesandmore6336]

Gabriel Silvaz ...thanks im working on a military b1 rc with steering in front and back to make crawling and trailing a lil better plus working on different suspension ideas , im just waiting cor new parts to arrive but as soon as i get them ill make video ... Gr8 video by the way now i know what not to use lol...take care my friend .

[@gabrielsilvaz4199]

RC Crawlers 😉

[@Alamander81]

I have the “320 amp” esc and I can confirm it can not handle near that amount. After 2 mins in my sewed slash with 18/80 gearing it went into limp mode and got hot to the touch. It would probably handle a 380 just fine b and I’m sure it would be great in a wpl or similar size crawler with a low current draw

[@gabrielsilvaz4199]

Alessandro Troiano I use these all the time with 3S Lipo they handle it just fine For over 45 minutes with small N20 motors-370 motor I have 15 trucks with that 320amp ESC! I think I have a larger test sample than most people for six dollars you can’t beat it the price is changing all the time

[@roadstar499]

i think you did not explain how to do anything here...no instructions come with this thing...

[@gabrielsilvaz4199]

This is a comparison video not an explanation video

[@coreyf117]

is the wpl rtr esc lipo capable?

[@gabrielsilvaz4199]

Corey F I’m not sure? but I know the four channel WPL remote is!👍

[@legoengineworkshop5171]

Can you use 7.4v 2s lipo for that cheaper esc?

[@gabrielsilvaz4199]

Yes

[@legoengineworkshop5171]

@@gabrielsilvaz4199 thanks

[@FogRC]

Привет! Я купил и поставил такой же регулятор ESC водозащищенный на 320а, но теперь у машины почти нет заднего хода. Это из-за него, или я что то не так сделал?

[@gabrielsilvaz4199]

Fog RC sorry I don’t understand 🤔 your message I only reading Spanish and English if you get some to translate for you maybe we can talk thanks for Watching👀👀😊

[@FogRC]

I thought everyone knows how to use an interpreter))) Well, it does not matter. Here's the message: Hello! I bought and put the same ESC waterproof controller on 320a, but now the car has almost no reverse. Is it because of him, or am I doing something wrong?

[@gabrielsilvaz4199]

Fog RC oh I see😅 will the ESC only puts out half it’s current capacity in reverse this particular ESC does not have rock crawling Mode if you want rock crawling Mode go with the hobbywing ESC like the ones I talked about at the end of the video they have rock crawling mode which means you can switch from brakes to crawling mode. crawling mode gives full current output in both forward and Reverse but no brakes. So I hope that answers your question the ESC I use in my jeep and Toyota works great in forward but you are right reverse seems realistically slow or powerless compare to forward but it comes with brake option try it without the brake option and see if that helps you in reverse I have not tried this yet if it’s like my hobbywing 1060A speed controller it might give crawling mode and maybe you will get full power in reverse if you complete this before I do let me know how it goes! I might try this later thanks for asking I never really thought about it😉

[@FogRC]

Thank you for your reply. So the whole thing in ESC. now I am calm. This ESC will go to me on a leiwick, and on the WPL I'll put as you have a second, a small regulator. By the way! And on a small, the same is only half the power in the back door, or not?

[@gabrielsilvaz4199]

Fog RC I believe the smaller ESC only puts out half power in reverse if you have the brake option. The brake option is mainly used for race car RC‘s because if your race car RC was on crawling mode it would go the same speed in reverse which would not be very good for stopping in forward without breaks could damage differentials with an abrupt stop. I have a WPL - B1 with a fast motor that made my truck run 15 mph and I was using The small ESC without break option and I stopped without brakes went in reverse stripped out the differential gears! Some people use the small ESC for DIY Robots that don’t need brakes they need equal power in both directions. Thanks again asking😊

[@ericcxxxx]

320 not to much for the motors

[@gabrielsilvaz4199]

Eric Anderson no the 320A ESC is not to much for the 12v N20 motors at all. I’ve been using 18 gauge wire

[@ericcxxxx]

HSP HPI 320A Brushed Speed Controller ESC

[@ericcxxxx]

At banggood

[@gabrielsilvaz4199]

Eric Anderson I’m not sure if you can find it at banggood I bought these ones on eBay.com

[@welshpete12]

Anyone know were I can find a manual for a BDESC-S10e-RTR ?

[@gabrielsilvaz4199]

welshpete12 🤷🏻‍♂️

[@gabrielsilvaz4199]

Everything you need to know about the ESC is labeled on it and They don’t make a manual for this ESC! I don’t recommend this ESC if you’re a beginner. I believe the Speed controller is rated for 18 and above......I wouldn’t say it’s for experts but definitely not for novice

[@welshpete12]

oh ok thanks for the info . @@gabrielsilvaz4199

[@ericcxxxx]

Links for the Esc pz

[@gabrielsilvaz4199]

Eric Anderson Sorry I haven’t been able to put the link up for those ESC’s but if you simply type in the information I gave before the specs on the video you should be able to find the ESC on Amazon or eBay Instantly although not quite As fast as a link I’ll try to work on that thanks for Asking

[@ericcxxxx]

@@gabrielsilvaz4199 thanks for replying

[@emersonpedro3944]

Show,,,,,,,,,,,,

[@gabrielsilvaz4199]

I’m showing you the specs............