The Charlie Show /// Episode 147 /// Complete WP1080 Brushed install

[@rcflashcars]

cool vid! 👍👍👍big like!

[@stevenbrooks7776]

Thanks for the info, I found it very useful

[@trevorlyle6381]

nice,thank you for the show

[@carnivorouslee]

My favourite brushed ESC! Although I do like the axe combos too! Great video!

[@wordreet]

Thanx Charlie, this helped me out. 👍👍👍 My second name is Charlie by the way. 😁

[@mikeashbaugh7773]

Great video, I just bought the HW1080, going to add it to my barrage gen 2

[@dschenk952]

Thanks, your videos helped me a lot. I am changing all my ESCs to 1080s, I like them so much. :)

[@fernandocabral6193]

I have a 1080 their awesome esc's Hobbywing makes awesome products for Rc's

[@AngelTorres-nb9nx]

5:48 where did you get that thing from

[@enricomiceli5517]

Hey, thanks for the content! Can i use the program plug (the three cable exposed) to pu a fan? Will the output be sufficient? Thanks!

[@HOBBYWINGOfficial]

It's more for Tuning devices and not suggested for "all" fans. Some of the fans out there, draw a bit more then a Normal fan and can lead to basic problems. You can, plug the fan, into the receiver so it runs from the actual BEC power output of the ESC that is made to support power outputs.

[@blowback8852]

What color of esc 1080 wire will go to the positive of stock trx4 titan 21t motor?

[@cupcakeman84]

Is it possible to use that ESC just plug n play replacing the old crawler ESC without setting board/card?

[@HOBBYWINGOfficial]

yes, most all ESC's work completely fine without any extra tuning. Just install, and Calibrate.

[@AngelTorres-nb9nx]

The battery comes with the car right or do you have to buy it

[@AngelTorres-nb9nx]

The one that goes in the little empty box inside the thing

[@thereviewguy5598]

I did this upgrade and noticed that I was getting more punch in reverse and slow I'm forward. My radio days reversed . Should I re solder the wires instead of turning down the forward force and turning up the reverse?

[@HOBBYWINGOfficial]

After install, then calibrate and test. Change the motor wires to correct the Direction of the motor. Do not use the radio channel "reversing" to fix motor direction. You can email us directly - [e-mail] for more assistance if needed.

[@satriyodirikamulyan1085]

Very useful information, i am a beginner in rc world, and i've a question related to brushed esc, battery and brushed motor. whether the number of cells in the battery can cause a short circuit on the esc ? Previously I used HW 1080 with a 5 slot 20T bruahed motor, the battery I used was 3S 5200 mah, at first it went well, but then the RC could not be moved, when I observed it, I found the esc was hot, end when i use 60A esc, the esc was lit and burn, can I get an explanation from a any of you here regarding what I experienced. what caused it and how to prevent it from happening again in the future. thank you so much for helping.

[@HOBBYWINGOfficial]

Hello, you can send us an email for more direct assistance. [e-mail]

[@metallbloodxox]

So can I run a light set / light bar from this esc ???

[@kevinduron300]

Hey, I have a question about this Hobbywing 1080 esc, I recently installed 1 on my axial scx10 II and 2 days ago my servo stopped working, because the servo circuit burned out and since that day My esc works like crazy, (it did not turn off when I hit the power button) and today it did not work when I turned it on the esc, the power led is flashing and esc does not turn on ... Please, I need help with this.

[@michaelnicholas9086]

Apparently you've never dropped hot solder on plastic. I wouldn't solder over the chassis like that without something protective between the wires and the chassis.

[@nicksrcadventures6831]

I purchased one of these today and I've had no luck with the calibration process, could you maybe help me troubleshoot this issue?

[@nicksrcadventures6831]

@TheForzaBro yeah, channel 2 in my receiver burned out. Worked perfectly after I put a new one in

[@nicksrcadventures6831]

@TheForzaBro I found out because my throttle wouldn't calibrate. I put the 1080 in my truck because I thought that my esc was bad but found out it was my channel 2 the whole time when I went calibrate the 1080. But if you take you servo plug and plug it into channel 2 and you have no steering then channel 2 burned out in the receiver

[@nicksrcadventures6831]

@TheForzaBro no problem man, glad I could help you get it figured out

[@auditionsongsforthevoice.3849]

Maybe you should read the instructions a little better . You hold the set up button down until you hear it beep once then let it go . At that point your in set up mode for forward , forward /reverse / stop and forward /stop. Your heard itbeep once now hit the set up button once more and it will beep twice . Hit set up one more time you'll hear it beep 3 times. That's how you do it down all 9 settings

[@suhaiqalnorikwan]

how to fix when it blinking red??

[@HOBBYWINGOfficial]

Please send us an email for assistance. [e-mail]

[@zcorpionbiru4120]

combo hobbywing axe 550 3300kv.. tutorial instaling with servo dw hd25. im from indonesia