The Hazet 1000nm Extendable Ratchet

Replaces the 1/2in breaker bar and your average 1/2in ratchet.
CORRECTION: In the video I mention, 90ftlbs +90 degrees for the torque requirement for the rear brakes on this car, in this case a VW MK5. It should be 90NM(66ftlbs) + 90 degrees. Sorry for any confusion this may have caused.

[@JohnStonerxD]

Hey there from Germany! 👋 I just wanted to say great video, I enjoyed watching it 👍 You're absolutely right about that ratchet considering the versatility - you get 90 degrees inside the ratcheting mechanism, it can withstand 1000 nm of torque and you can extend it. I'm actually also considering to get one of these since I broke my cheap taiwan torque wrench (28-210nm), which you also get in the US from ICON, Harbor Freight and so on - of course I didn't use that one as a torque wrench since the torque setting mechanism was broken before, but I broke two teeth of the ratcheting mechanism when tightening an Audi A4 Wheel Hub Nut (200nm + 180°). The only unfortunate thing about the Hazet is that it is quite expensive (110€ here is the cheapest) but as always you get what you pay for so I would say it's definitely worth to buy it eventually 😁 In that sense keep on going with your videos and all the best 👍🙏Cheers

[@oldguyramblings]

Thank you. I try to buy tools that last. I have had some of my tools for over 40 years. The Hazet may be more expensive, but in the long run it pays off. If you noticed the 1/2in old Craftsman breaker bar, the handle is bent, but the head did not. Don't make them like they used to. I use the heck out of the Hazet. I don't know if I would use it on a hub, but it should take the heat. I figure that is what my 3/4in breaker bar and pipe extension are for. ;-) If you are looking for a excellent torque wrench, try Precision Instruments TQs. I have had mine for a number of years. Really nice. Not cheap, but well built. There is a video on them, here: Thanks again. kzbin.info/www/bejne/pqmriH2DgqiZh5o

[@JohnStonerxD]

@@oldguyramblings Good evening 🖐, it's true what you say, I'm kind of following the same philosophy when it comes to tools. 3 years ago I bought a very basic set of sockets and ratchets (1/2, 3/8 and 1/4 inch) with which I wasn't happy at all so I started collecting all kinds of tools that I needed from reputable brands on ebay or second hand - Some of those are manufactured in Taiwan but I also collected a decent assortment of preliminary German made tools. For torque wrenches I decided to go with Stahlwille, since it is the only brand that uses a different mechanism that doesn't need to be reset to 0 after usage plus you can also change the head insert depending on your application - these are quite pricy but they can be found for a fair amount in the second hand market here. I think in the end you always have to decide which tool to buy based on the application/frequency of usage - for example I have a cheap manual brake piston retraction tool, if I can call it so 😅, that is especially useful for the rear brake pistons of VW and Audi cars where you have to push and turn at the same time. It does the job and was not expensive at all so it's totally alright for me to keep that one as long as it's functional. Considering the Hazet I have to say that I really need that one because I don't have a breaker bar as of yet (they are not so common here somehow). I've also seen an english video where someone actually tested the 1000nm on the long version and it actually came very close to the rated number so I guess in terms of strength it's quite a beast 😁 Here is the video for you: kzbin.info/www/bejne/pYTdn2qNmNKImLc Keep on going with your channel and all the best 👍👍

[@mrcokez1]

i ended up getting this ratchet too, very pricey but worth every penny for how stout the ratchet is feels very heavy and very premium not to mention their gearset is pretty smooth and strong

[@oldguyramblings]

Nice. The only 1/2 inch ratchet I kept was the one with the swivel head. Yea, upfront cost are higher, but I believe this tool will go the distance.

[@EdAtoZ]

Old Guy, I just got the Hazet 916HPLG last night and yes this is a beast of a ratchet, Question have you looked at the Facom flex extendable ratchet ?

[@oldguyramblings]

3/8?

[@EdAtoZ]

@@oldguyramblings Facom makes them in both 3/8 and 1/2 dr. Facom part number SXL.171

[@oldguyramblings]

Facom makes great tools and I have a few. Seeing that you have the Hazet, are you looking at these for the Flex heads? Personally, I am not a fan of flex head ratchets. I have had few over the years, but I always find that the head is weak point. They seem to get loose and don't hold an angle. I prefer using a impact swivel head extension. 3/8, 1/2, or 1/4. Now if you do want one, then that type by Facom is the kind to buy. The extensions are adjustable at any length, like the Hazet. Avoid the ones that lock at only certain points on handle. @@EdAtoZ

[@EdAtoZ]

@@oldguyramblings I was thinking in the area of companion. The Facom longest point is basically the Hazet's shortest point. So I think the two allow for the widest working range.

[@EdAtoZ]

@@oldguyramblings They do make fixed head see "Facom 1/2in Drive Pear Head Extendable Dust Proof Ratchet Reversible SLX.161"

[@connor3288]

90ft lbs plus 90° for caliper bracket bolts?! That sounds WAY overkill😲

[@oldguyramblings]

You are right. It is. Guess I missed. It should be 90NM(66ftobs) + 90 degrees. I will have to put a note in the comments. Thank you for pointing that out. Unfortunately, YouTub won't let me update the video, once it is posted. Thanks again.

[@BrianHolcombewoodworker]

Beautiful ratchet! Fair warning that collecting German tools is dangerous!

[@oldguyramblings]

@@BrianHolcombewoodworker Having VAG cars for 50+ years, you gather a few German tools. Plus, the tool is always cheaper than having someone else do the work. Unfortunately, as American tools become Made in China, you look elsewhere for quality tools.

[@mcqcjc8409]

U talk like someone who has plenty of time and does not use electric or pneumatic tools.

[@oldguyramblings]

Wow. How do you answer a negative, when you are trying to be positive? I bought my first 1/2" pneumatic impact and pneumatic ratchet over 40 years ago. When did you buy your 1st ones? Electric and pneumatic both have there place. Sometimes close quarters don't allow the use of either. If you put extensions on them, they lose torque removal value along the extensions, giving you less strength at the fastener. In this particular spot I am working on, at the end of the video, there is very little room to get an electric impact in around all the suspension and springs.