The SECRET to never clogging your airbrush again!

Рет қаралды 10,512

Күн бұрын

Пікірлер: 40

@howardcobb4354 11 ай бұрын

Excellent- very useful tips which should ease my painful entry into airbrushing 😢. Nice straightforward video too - no frills, just a demonstration of the advice. Thank you.

@justmakesstuff 2 жыл бұрын

I always watch these things looking for some secret I've missed. The never let your cup run dry, and never flush forwards points are great. I'll bear those in mind!

@DavesMiniMenagerie 2 жыл бұрын

Thanks mate, I hope they help. Tabletop Minions has a vid about his airbrushing and he goes further, he just leaves his airbrush in a jar of water so it doesn't dry out at all. The flush forward thing, I've seen a couple times a bit of dry paint from the cup dislodge and then get stuck in the nozzle when I flush out the tip so I don't do that anymore. I think I got that tip from Vince Venturella

@tonychristney2728 3 ай бұрын

there is a seal between the front and back of the airbrush that requires the needle. I don't think you should completely remove the needle with liquids still in the front of the airbrush because it can allow those liquids into the back where it is much more difficult to clean, especially if it makes it all the way back to the air valve.

@Gaz77a Ай бұрын

I agree. It is also why the blow back technique can lead to paint flowing into the back of the airbrush.

@hewlett-packardlovecraft2297 2 жыл бұрын

Nice to be able to leave comments on your videos again; PC went down on me a few months back, and I had to revert to the 'ol PS3 to watch YT. Now that I can finally afford a new rig, I find I have to re-learn YT from scratch. Poor me, right? Stellar work as usual, though- no one else's videos bring a smile to my face quite like yours. Eternal thanks for that, and I hope the day finds you well. Enjoy the rest of your week.

@UrbanGarden-rf5op 6 ай бұрын

Wow. Thorough and well presented. Perfect for a newbie like me. You even showed a flow diagram. That's rare. I will definitely check out your other stuff. Thank you ✌

@TheGoldenDragon_ Жыл бұрын

I'll try this when I try out airbrushing for the 1st time. Just recently got a cheap airbrush but haven't had the opportunity to give it a go yet. Thanks for the tip, Dave. Love the vids.

@neilsells1155 7 ай бұрын

Youre a life saver, I have been cleaning my airbrush by shooting cleaner through it. I will always pour out the cup. Thanks!

@AndrewC6 10 ай бұрын

Thank you for the great information. 🙂🐠

@TheBasicBrush 2 жыл бұрын

Great to have you back 😁 Some great advice, I need to soak mine completely at this point 😭

@DavesMiniMenagerie 2 жыл бұрын

Thanks man, yeah the plunger part of my airbrush is getting a bit sticky. I think I'll need to soak mine and pull it apart to get that sorted out. Maybe I'll just upgrade though... I've got a hankering for a fancier airbrush

@jamesedwards8175 2 жыл бұрын

Yay! You're back with a great vid! The tip that I've discovered is that the old school advice of cleaning with Windex works great for SOME paint, but others it will turn into a paste and make you have a bad time. I think it's primarily due to the pigment (whites are the worst), but I don't use Windex as my primary cleaner anymore.

@DavesMiniMenagerie 2 жыл бұрын

Thanks man, its good to be back. I've found whites to be really difficult as well, they are so sticky and get wrapped around the needle for me. I heard that Pro Acryl titanium white is the best around but I haven't tried it yet. My cleaner doesn't get everything out either, I'm a bit nervous about using something a bit stronger though

@kullervo3289 5 ай бұрын

Useful video. I just got started with a Timbertech airbrush, slowly getting the hang of it... Unfortunatly tip clogged so now I'm here 😅

@Dre_day82 3 ай бұрын

Thanks!

@NarcolepticLTD Ай бұрын

I pretty much use the same method. I'm lazy and haven't had to break down my airbrushes for months at a time (other than pulling the needle). The only thing I do differently is I only backflow the air when cleaning, not to mix paint. If the barrel is already full of thinner, putting in the correct ratio of paint/thinner afterwards - a quick mix with a brush will mix properly, and then a blast on a paper towel will push out the pure thinners in the front and now you're loaded for bear. I also don't bother buying branded airbrush cleaners. Distilled water first to dilute and dump the remaining paint in the cup (with a backflow) then just follow up with 90%+ Isopropyl alcohol

@alaingay 2 ай бұрын

Good old Vince advise ;)

@Indyjeeplover 10 ай бұрын

I used to try to mix in the airbrush bowl, but I personally have better success mixing in a small plastic cup. I can more easily tell how thick or thin my paint is. I use some original Createx paints and some are very thick (think gravy) and need about 1/3rd reducer. I also add in Createx 4050 which is a flow improver. Doing this makes the paint flow better, adhere better, and makes cleanup much easier and just about eliminates dry tip If you keep a small bowl of a 50/50 mix of water and alcohol with a small sponge in it on your table top you can dip the end of your airbrush against the sponge to easily clear dry tip should it occur Createx Restorer will pretty easily and quickly clean out dried paint. Disassemble your airbrush to soak the parts. You should not blow it through the airbrush

@preid1 2 жыл бұрын

Can I use these tips to paint my ute though...?

@DavesMiniMenagerie 2 жыл бұрын

Yes just very very slowly lol. I'd love to see you paint a ute with a 0.3mm needle airbrush haha

@rupertbrink2081 9 ай бұрын

Ahhhh lol… most Australian comment ever

@ineedfiles 9 ай бұрын

good stuff

@gerbendenheeten6905 6 ай бұрын

I have a jar with boiled water next to me, and after a few sprays I pull out my side cup, clean it with the hot water, also put some hot water in my brush, and use a brush to clean the nozzle top, and spray some hot water, and then I am ready for a next round of colorspraying.

@GnaReffotsirk Жыл бұрын

Isnt blowback also the cause of clogging?

@_PhamTuanCuong 10 ай бұрын

How can I prevent clogging internally with the airbrush? It's painting fine today and the next day it always clog inside for me, even worse if it was after a priming session