The teeth of the drive shaft are broken | See how our method is fixed | Amazing work

#driveShaft #shaftBroken #repair #restoration
#technology #amazingtechnology #engineering #pakistanitruck #repair #engineer #restoration #things #repairgearbox

[@user-ip4fo9ub1b]

Хух, а я уже думал шлицевую наваривать будут. 😁

[@Alex_N_Nov]

😂😂😂 Аналогично

[@konstantttin1981]

Обленились уже.

[@jenyarya07]

Я такого же был мнения, после попавшегося мне предыдущего видео от этих индийских чудо умельцев. Думал как наварят электродом а потом болгаркой пропилы сделают и как новая.

[@turanellervarolsundirilis9267]

@@jenyarya07 да но они Пакистанцы .

[@user-mh3vs3ub5h]

А кардан-то давно самодельный, труба водопроводная.

[@kennethney4260]

Can't believe they forgot the final step where they toss it in the dirt.

[@bobbybowers4065]

Lol hahahahahaha yeahhhhhh about pissed myself when i read that...funny shit bro!!!!!!!!!!

[@TOONMAN200]

@@bobbybowers4065Ya you're right they forgot to roll it around in the dirt before they install it. I have watched many of these videos always include working in the dirt. Maybe it's a sacred Pakistan ritual putting the part close to the earth, for good luck.

[@Alex_N_Nov]

После гипоида балансировка кардана это так, детские шалости😂

[@user-rn3sn4lh7r]

Если вы увидите как они делают ремонт блока двигателя будете в шоке 😂😂😂😂😂такие дыры ремонтируют легче всего б/у купить 😂😂😂

[@user-jj7tz5bi7n]

@@user-rn3sn4lh7r вы ещё не видели как в Польше лепят.

[@billmiller7138]

Actually a reasonably proper repair on one of these channels for once! Holly shit! Wonders never cease!

[@Mercmad]

A lot of these component failures appear to be the result of their practice of buying small (1.5 to 2.5 tonne ) trucks and extending them to carry bigger loads than the components were designed for . That,and the quality of the Chinese built trucks such as great walls etc.

[@terrafarms7370]

'Wow' A Machinist that looks after his equipment. High praise to this guy who appears to have the cleanest workshop ive seen so far.

[@mandyfung9239]

尸dd

[@3rdgenbestgen21]

Im a welder and I work with Machinist in the military and in charge of the shop. I don’t let my guys leave until the Machines are clean up for the day. We also have a Honing Machine , 2 lathes and 1 bridgeport which makes the most mess. I mean do you know easy it is to get a Machine that cost 500k? It’s not easy at all. So we maintained it👍

[@frankbol700]

eehmm....they weld on there leathes...i mean is not great for youre bearings just cleaning doesnt mean machines are good and what i saw and heard in this video that machine is not in a good shape

[@skunkjobb]

When welding in the lathe, I hope you put the grounding clamp directly on the part you are welding and not on any stationary part of the lathe. Current passing through the spindle bearings is a quick way to damage them.

[@therealspixycat]

Indeed: use a flat car battery ground cable in an o shape and connect this way the ground. Or temporary weld a small shaft with a brass baring that hold the gound. You will also notice that welding is a bit easier because of the consistent ground

[@BobSmith-mc7uq]

You KNOW they don't do that. Ground to the bed or ways.

[@johnghatti5435]

How does welding the way you mention damage the bearings in the spindle? Not sure how an electrical field would do that. It wouldn’t heat the bearings by welding that way but I’d be more worried about the electrical part of the lathe.

[@therealspixycat]

@@johnghatti5435 there are multiple greased (read electric insulated) small contacts points between the the two casings and the bearing balls while the current is large: the grease will melt and the balls will fuse damaging the bearing itself due to the high current on multiple places. The bearing was never designed to be a high current rotating conductor. Plus welding is sometimes sub optimal because of the bad ground.

[@georgegonzalez2476]

That's only true if you have been oiling or greasing the bearings. If they are dry, then current has an easier path through and doesn't spark over so much.

[@Bradford1able]

Beautiful job with basic equipment. Well done fellas.

[@jjohnson1476]

After watching what seems like hundreds of these videos, Im convinced that all young men wherever these videos are filmed are born learning how to operate a lathe and a stick welder!

[@daciatravel.647]

Very nice work!

[@eniltonmachado5900]

Parabéns . vocês são muito talentosos

[@ricardoaniballosadaherrera3690]

Soldar sobre el torno, sin colocar la masa sobre la pieza a soldar , es un error fatal . Los rodamientos del torno se deterioran por el arco que se forma en su interior 🙄

[@FernandoAlegre]

Soldar sobre las bancadas. Soldar sin precalentar y retardar el enfriamiento. Seguro se fisuro el cordón.

[@damianhsjswjjsjshwdjdj]

Lo deben saber, pero se ve que andan apurados los muchachos

[@user-jj9en2qb4x]

Первый раз в подобных роликах увидел штангельциркуль!!!

[@silviomanyel3394]

Штангенциркуль, думаешь они умеют им пользоваться?

[@user-cj2hw9zs6y]

Тут главное загнуть электрод

[@mightyfinejonboy]

love how the lathe has been cared for👍🏼

[@user-wc2qr2hv6b]

Привет

[@Jack-tx2ve]

I thought the same thing. Kept clean.

[@juhajuntunen7866]

Maybe its more expensive than his house.

[@Jack-tx2ve]

@@juhajuntunen7866 maybe he loves his tools and the way they provide him with a livelyhood?

[@arleylondono647]

Excelente video muy bien grabado felicitaciones sigan así de bien

[@douglasmacomber2277]

You guys make everything look so flipping easy!!!!! From Boston 🇮🇹

[@nunesmotos351]

Trabalho incrível super dez

[@mrwhite2930]

Just a quick tack over the porosity 👌🏼

[@user-ib6br2up2f]

Не ну эти то по сравнению с другими всё чётко сделали ), особенно шов понравился, почти завод ), им только покрасить оставалось

[@Banksia]

The latest Micrometer measuring device, a piece of bent wire, i just love it!

[@seanmares2406]

Wow you guys do great work

[@azmanmdsalleh2009]

Another good job.... Alhamdulillah

[@readthebible1958]

Good job but cover the splines to protect from welding balls sticking.

[@VenturiLife]

And cover the lathe up with something underneath when welding. Clever though gripping it with the lathe to stop any movement when welding it up.

[@livefreeordie5033]

Awesome work by awesome people 👍 Cheers ⚘🇪🇬⚘🇪🇬⚘🇪🇬

[@prof.rubinho]

Muito bom 😃🇧🇷🇧🇷

[@njm3211]

Looks like a competent repair

[@damiandiesel1]

Are you sure the word amazing is the right word for this simple lathe and welding job.?

[@dennisneo1608]

It is if you're not a conceited piece of crap.

[@johnnystoka6625]

@@dennisneo1608 Or maybe you are because there is truly nothing amazing about this work .

[@frescavena2004]

Not amazing but you know what, you saved the customer a ton of money by doing this. Here in USA that job would have cost over $2000 so in that sense , it was amazing !!! Question though - why not clean it and paint it? Would have giving it a final nice pretty touch…… just a thought

[@silviomanyel3394]

Индикатор из проволоки огонь! Измерения проводят в попугаях мартышках и удавах.

[@user-eq5ry5le6o]

Окометрический индикатор.

[@kazanbas3427]

То ли дело русские, измеряют в пездах и пуях

[@user-eq5ry5le6o]

@@kazanbas3427 и получается в результате -серая птица. Пусть Алиса переведёт на китайский.

[@kazanbas3427]

@@user-eq5ry5le6o вроде украинец а топите за русских...

[@user-eq5ry5le6o]

@@kazanbas3427 учился в русской школе, потому знаком с терминологией.

[@fc3srotory370]

Can't hardly find people in America to push a green button. Hats off to these gents.

[@3rdaxis649]

Christ there's just dirt EVERYWHERE?! Is there no concrete or pavement in this country? lol

[@gerardovelez219]

felicidades a estos maquinadores

[@lorenrasmussen338]

Hey, the ways on the lathe got oiled! But I didn’t see the ground cable get hooked to the driveshaft…… current going thru the headstock bearings?

[@subramaniamkmathvan3661]

Great work.

[@alitn588]

Beautiful..👍👍

[@letcikigor]

Super!

[@britishprofessor9957]

I call that proper recycling in most places you have to buy a new one. Well done👍👍👍👍👍👍👍👍👍👍🇮🇪🇮🇪👏👏👏👏👏👏👏👏

[@YourProcess]

great working process video~ 멋진 과정!

[@taimurmirza9419]

The spline end was welded without marking the alignment of the teeth, it would be pure chance that both ends of Crosses are aligned, if misaligned then there will be a vibration.

[@davidhamm5626]

Would it matter if it went into a slip joint ?

[@madprops526]

Yes it would. The universals will be out of phase. I think if you lines them up to the nearest spline it would hi old be pretty good....not sure how smooth the roads are there anyway 🤷‍♂️

[@akira5982]

they'll be driving to slow to notice, roads are probably non existant like the walls & ground of the shop

[@richardtemby4358]

Rubbish!

[@samuelquartey4617]

Excellent job

[@vinmarusop5592]

Very very good job 💯 persent

[@Jshankarpatel532]

🙏 👌👌👌👌👌👌👍👍👍👍👍👍 good work Sir

[@keithwhittaker5238]

Great repair bit they didn’t phase (line up) the uni joints ...unless they just didn’t show it getting phased . Even 1/2 spline will cause vibration/uni wear. Even worse if there was a master spline .

[@richardtemby4358]

What a load of rubbish you state, there is only one u-joint, there is more chance of upsetting the balance by unevenly welding the replacement spline on. Just sayin!!!

[@Jack-tx2ve]

I thought phase was between two uj's. Because uj's output rotation is not a constant velocity.

[@beyondwhatisknown]

Thanks for mentioning the need to synchronize. I see what you mean.

[@ScatManAust]

@@richardtemby4358 Now you are showing your ignorance by rubbishing Keith Whittaker and phasing. There is and will be a minimum of two joints Phasing is critical in balancing the shaft and expecting it not to vibrate. True welding the spline on the piss is very bad but and will have serious detrimental out come but careful alignment, phasing and dynamically balancing is absolutely required for smooth trouble free operation.

[@rowo86]

О технике безопасности парни даже не слышали....

[@shels666]

Их много :-D

[@user-is2oj3dq5n]

More than one pormal turner would not allow welding on a lathe and still clinging the mass to the machine through a bearing.

[@alvarofernandezvega464]

Yes, a friend of mine told me about electric abrassion due bad earth grounding in train bearings...

[@donaldnye2890]

looks good but a straight spline and a 6 foot drive line at even 0.005" off is 0.060" off at universal joint and since it is more then that off should chew everything up fairly fast.

[@halcondelasierra3625]

0.007” and 0.062” my dear fellow. Get your measurements straight homeboy.

[@SmokinSmogHog]

2:04 sick beat!

[@anwornation3399]

Very good work

[@ricardofonseca678]

Já fiz muito esse trabalho. É exatamente assim, muito bem feito o serviço no cardam do vídeo. 👍👏👏

[@ginobragoli1448]

Usually those shafts are balanced but I'm sure the truck it goes into will be just fine! Good job done👍

[@akira5982]

they should be balanced but they probably wont be doing the same speeds we do on our express ways so it might not reach imbalanced speed or they just dont care, i mean a lot of there buildings dont even have walls so imagine the pot holes n shit in the roads 🤷‍♂️

[@MrHBSoftware]

shafts with u joints and center bearing support like this one dont need any balancing...they need to be roughly straight and thats it....often u joints have play in them and when you replace them you end up messing any balancing and yet they work just fine

[@ll_fabrellas]

En cuantos canales se ha publicado este video?

[@cliffchilders5820]

Its called a spline..... Not teeth!!! Just so you knw!!

[@Hazaratruck]

Very nice😆

[@djbillye4943]

Will the bead of weld held the forces

[@SlavaBushuyev]

Станки новые прям красота 👍👍👍

[@dakshmadhok338]

A wonderful demonstration of how to replace the spline shaft. We are Allied Gears India. A company based in New Delhi, India. And we manufacture drive shafts and it's various components. Kindly contact us if you need any product of OEM standards 🙏🙏

[@TieraRoot]

Невероятно, про часовой индикатор они не в курсе и бой на глазок ставят... Я поник головой, когда это увидел...

[@3RulonchikOboev]

Специалисты, я у бенгалов такого хэндмейда насмотрелся

[@andersonlopes5581]

Muito bom gostei do vídeo legal.😄😴😲😃😋😜🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷 BR

[@Scugnizzu]

Hello what electrodes do you use? Thanks

[@tinkeringaround6241]

Nice job

[@nardaoeletronica]

Very good 👍🏾. 🇵🇹🇧🇷

[@user-tl2in6sn1k]

Молодцы ребята .Привет из России.

[@eg3040]

Fast making of bell crank hole with welding and cutting on lathe, video needed.

[@ShionWinkler]

Wow, that is a actual fix!! Most of these videos they call fixes are nothing but Band-Aids that will fail in a few weeks or months. FYI that slip yoke at the end, ahh... that should be able to slide freely, not stick like that... May want to clean the teeth up and put some grease on it.

[@allthegearnoidea6752]

Nice new lathe

[@wankitkharpan6148]

Machinist is a good trade

[@taavey]

So where can I buy the welding rod these guys use? One video shows a closeup of 7018, but all of mine sheds the flux when I bend it. They bend every single rod and weld through the bend with no problem.

[@henryrollins9177]

Humidity does that trick...😀

[@georgegonzalez2476]

They may be less than top spec rods with a mild tofu coating. It's awfully tempting in poor countries to buy the cheapest available tools and consumables. True 7018 rods are rather expensive since they're mostly Nickel. I can see a market there for faux rods at a vastly reduced price.

[@mnocum16]

Hahaha I guess the title was very wrong here its not just the teeth the damn whole thing is broken.

[@leinadalan]

Tell ya what, this channel has blown up. Someone is rolling in the dough.

[@scrapbongo786]

Amazing how you can fix that. New Sub. /cheers ScrapBongo Liked

[@mikescalise2452]

nothing like making ground thru the spindle bearings.

[@roygangoo1744]

welding, magic.

[@ROADKILL4147]

nice job and pitty he didnt clean the rust out of it or clean the other end

[@VenturiLife]

Yeah, when a tube etc. is sealed air-tight like this one was, what happens is, it gets some surface rust like that from the trapped air when it's closed up and welded initially, but it stops rusting because all the oxygen has reacted with the iron, and all that is left is mainly inert nitrogen so rust ceases at that point. Removing all of the rust would actually cause the rust process to start over again. This is why a sealed piece of steel tube will rust from the outside to the inside. I was hoping they'd clean the tines on the shaft itself, but maybe they did that later before installation.

[@kulinich985]

Микрометр? не, не слышал.... Биение? Да проволочку сейчас зажмём...... Жесть.

[@stevem3413]

Isn't it necessary to balance the drive shaft so that there is no vibration.? But otherwise a great job thanks

[@mackebest1995]

not really from the looks that is a one piece driveshaft (no suport bearing) so no need for that especially not if it isnt any high speed/performance application

[@akira5982]

guess ya wont know unless u get it balanced or chuck it in & see what happens Orrrr they wont be doing the speeds we do on our express ways to reach imbalanced speed as there roads are probably full off pot holes n shit.

[@ronblack7870]

the roads are so shitty that the driver will never notice if there is some vibration.

[@engineerma]

👍👍👍👍

[@Automaster4322]

А балансировка кардана?

[@donwright3427]

Good hundred fast lathing is funny nice I got metal is hard to make smooth way

[@franciscowashington2155]

Beleza 👍👍👍😎

[@marcelrustice8221]

Olha como eu queria trabalhar um mês com com vocês teria um bom aprendizado

[@craigthompson1794]

Spot on boys

[@atexnik]

Please, remove that artificial sounds when you speedup the video. Unbearable.

[@AffordBindEquipment]

2:37 he's actually oiling the ways!!! someone who cares about his equipment! except for the welding part...maybe the oiling was to keep the splatter from sticking. But the bearings sure took a beating with the welding.

[@mrb.5610]

Assuming that was oil and not just goat's piss.

[@AffordBindEquipment]

@@mrb.5610 Hey, it might work for awhile... and then every thing rusts away...there is that.

[@TheRealWillM]

For a minute there I thought the were going to weld the 2 halves of the splines together. I'm also surprised that they don't use mig welders unless getting the gas is the issue?

[@OnotoleRealne]

Я удивлен, они направляйки на токарном даже маслом помазали)))

[@user-ey5yy1ou2p]

Интересно они знают что такое балансировка

[@user-jj7tz5bi7n]

Не партесь, вы много раз видели, чтоб после замены крестовин делали балансировку. Уверен, что нет. Зато метки на фланце ставят.хотя в целом в 90% все норм.

[@gerardconway4927]

Why don’t they lubricate cutters ?they’d last longer

[@mehmetakifcam953]

Isıl işlem görmemiş, yani metalin yumuşak olmasından dolayı kesici kalemler yağlanmıyor. Eğer ısıl işlem görmüş, sert çelik olsaydı, bor yağı kullanması gerekirdi. Bu tür yumuşak metaller, kesici kalemlere zarar vermez.

[@cicerofoscarini8890]

where is this place? does anyone know?

[@user-xy3gx4jt3k]

Что-то подобные видео часто в тренде.К чему бы это...🙂

[@therealspixycat]

That is smart: having a sort of chuck on the back of the chuck to align the entire shaft

[@ThisIsToolman]

Referred to as a “spider”...

[@savasozturk8618]

Türkiye'den selamlar bura hangi ülke

[@ermekz9740]

in the beginig minions are laughing at something

[@Use_2024]

Почему не 3-х кулачковый патрон? Или 4-х лучше?

[@silviomanyel3394]

Бро, ты индикатор видел? Они все в мартышках измеряют, какой был патрон на таком и работают.

[@viktorbash2020]

@@silviomanyel3394 Индикатор фирмы mitutoyo, Сварочный токарный станок, палили маслом ,чтобы не ржавел,Но тутже на нём варят.

[@RicoJovanni]

4 видимо дешевле (не самоцентрирующий) и универсальнее в их условиях. Они на токарниках делают все, от батона до г@ндона.

[@alextrofimov6208]

Сварка на станке вообще шедевр. Да и шлицы можно вообще от говна не очищать, так молотком забьют.

[@jean-lucvabis2529]

pas de lubrifiant?

[@stretchhfab7315]

Nothing is impossible and anything can be fixed.

[@frankanddanasnyder3272]

You had to fix your method?

[@seetheforest]

Splines not teeth. Splines are on a shaft.

[@timur-wo3sv]

Крестовину зафиксировать не хватило ума?

[@170119911]

Интересно где они взяли другую шлицевую? Отрезали от целого кардана?!

[@EMUISTHEONE]

Why leave the u joints in

[@dabyd64]

Sounds like a mice factory lol