Hands down the BEST most reliable and affordable perfoamnce mods you can to to your crown vic, town car or grand marquis all for UNDER $1,000
Пікірлер: 577
@alexplowski5523 жыл бұрын
Nobody is doing a 5 speed swap for $400, considering you need a tune from marty (costs more for that tune than the auto tune) Plus you need pedals, conversion ujoint, correct yoke, adjustable clutch cable, quadrant and firewall adjuster. Oh yea, then you gotta buy a trans, Clutch and Flywheel... Lol
@leroybrown60063 жыл бұрын
I was trying to figure out the same thing, like who tf is his mechanic? 😅
@Elver_Galarga_jugo2 жыл бұрын
Shit trans alone is already well over $400, and you still need the clutch, flywheel, peddles quadrant and cable….
@alexplowski5522 жыл бұрын
@@Elver_Galarga_jugo I swapped mine for a bit less than a grand, and that was cheap AF.
@Elver_Galarga_jugo2 жыл бұрын
@@alexplowski552 the more I look, I can’t find a T45/TR3650 for less than $800 anymore, I’m just lucky I have a spare even if I have to rebuild it
@SRT922 жыл бұрын
I was laughing as I got towards the end of this comment 😂
@captaincobb8146 Жыл бұрын
I love my 2007 Ford Crown Victoria P71! Today it is in outstanding shape. Even though it has 185,504 miles and 6,136 idle hours. Over the last five years I've owned it, I have rebuilt the transmission at a premium Speed Shop for $3.8K. Water pump, alternator, starter, rear axels, and rear wheel bearings, all with lifetime warranties. Intake manifold, injectors & coils. This car sat in a body shop for a very long time. The front and back doors on the passenger side do not match the vin#. No frame rust, but my next project is to replace both front quarter fenders and a new paint job (it is white, so it will stay white. Right after I had a new set of "W"(168mph) rated tires installed. I took her out for a run. Yes, the P71 isn't the fastest thing off the line, but at 155mph she makes you feel like you're only doing 40mph. She just sets down on the road and goes, All around my neighborhood people have these new cars and SUVs, yet I know, for a fact, that I could chase each and every last one of them right down into the junkyard and still drive away. Not even these newer cop SUVs/Trucks would stand a chance in a durability test. It is truly the beast of beasts. I'm so proud to be the owner of such a clean example of the 07 Crown Vic P71
@thetinpin3 жыл бұрын
Remember that if you use a K&N filter you need to clean your mass air flow sensor periodically because the oil from the filter loves to stick to the sensor's guts. When you clean and oil the filter, be sure you do NOT over oil! You will have MAF issues and possibly a CEL if you do!
@b85douglas2 жыл бұрын
thanks
@jasoncooper31162 жыл бұрын
That is what I've heard. That is why I haven't done it. I believe you may get a little bit better throttle response, bit not any noticable hp gains. To me, the cost and negative effects are just not worth what little benefit there may be.
@thetinpin2 жыл бұрын
@@jasoncooper3116 It takes like 2 minutes to clean the MAF, and K&N recommends cleaning/re-oiling every 50,000 miles. I clean my MAF once a year, so it's not exactly a soul crushing amount of maintenance. My butt dyno approves of the K&N. Besides, what else can you drop $50 on, install in 30 seconds, and get a tangible performance increase?
@rduonnolo2 жыл бұрын
I cut some holes in the bottom of my air box. Let's in a ton more air!
@thetinpin2 жыл бұрын
@@rduonnolo Errgh... the little tube that sticks out of the bottom corner of the air box is a crucial design feature because it pulls air from behind the headlight assembly where the air is significantly cooler than the air inside the engine bay. Cooler air is more dense (thus more richly populated with oxygen) than the warm/hot air created by the heat from the engine and exhaust system. It is a true 'cold air intake' straight from the factory. Only so much air can pass through the intake tube and throttle body because of inherent size and flow capabilities baked into Ford's design. The easiest way to enhance performance without increasing air volume is to increase the oxygen saturation of the air going into the intake manifold is to simply reduce the temperature of the air to take advantage of the more oxygen dense property of the cooler air. You have undoubtedly altered the sound of the engine, but I would be very surprised if there is a legitimate performance improvement from cutting holes in your intake inside the engine bay.
@Nathan_Jay3 жыл бұрын
I'd hardly say the manual swap is $400... You're gonna spend $400 on the clutch pedal kit alone, and that's assuming you don't have an 04+ with drive by wire.
@purritopoe48422 жыл бұрын
Maybe he lives in Texas
@CtheDead209-zt8tj2 ай бұрын
@purritopoe4842 doesn't matter if he lives in Texas or not the clutch pedals and fabricated drive shaft needed for this build to even work is over 800 now add in transmission clutch flywheel, quadrant linkage, and ECU flash needed... Try closer to 4k than 400...
@calebhallberg99383 жыл бұрын
A diy manual swap for $400 is almost a ridiculous sounding as having a shop do it for $1000. Both of those numbers are EXTREMELY low. Otherwise, over half would probably be manual swapped already..
@harrison4ever1252 жыл бұрын
Honestly
@terencecorley24502 жыл бұрын
Where did u get tht bumper at
@teejay6222 жыл бұрын
I had to hit the like button because they don't offer a "effin right!" button. DIY price is easily doubled and having it done at a shop is easily triple his price. Clueless!
@KashMoneyZack2 жыл бұрын
You niggas go up to one shop, they tell you sum bullshit, then u get puppy eyed feel defeated & quit. Lmao ask around, find parts dirt cheap, read how to do the shit yourself for little no money, the shit is not rocket science.
@eriv4735 Жыл бұрын
🤦♂️
@kayjglasjones22443 жыл бұрын
Soooo i have the Marty 93 octane which was $525. I have 4.10 gears set up $150 for the actual part , $1200 to install ....... FTI high stall torque converter which was $359 paired with a monster transmission that was $1200 I have the steeda underdrive pulley which was $250. The last three item are in the shop now being installed all for a total of $$1200. Just to give you guys an update on real time pricing
@rob-87423 жыл бұрын
Damn 1200 to install the gears in the rear end seems high but I've never priced it before
@blueovalfan233 жыл бұрын
@@rob-8742 you gotta get the lash right with shims. i can see it being a time consuming job. you gotta play with it, take it out shim, put it back and try it till it's right. the pinion has to be set to a certain depth as well before shimming.. it's one of those things that can be easy or a total pain in the ass. sometimes though, you get what you pay for that much in labor might sound bad but if you want it to last..
@kayjglasjones22443 жыл бұрын
@@rob-8742 naw thats about the going rate one shop quoted me 1000 but he wasn't confident on doing it. I ended up taking it to a performance shop who did it with ez.
@johngregory48012 жыл бұрын
As for the 4.10 gears, I looked into replacing my 4R70W instead of just putting a rebuild kit into it, but... If I drop a 6R80 in to replace it, I get a much lower first gear, with closer spaced ratios all the way to a .69:1 6th gear, so I still have overdrive for low-rev highway work. It costs a lot more, but at least I don't have to worry about my warranty expiring!
@rustybeatty65672 жыл бұрын
Would do to upgrade it to a 3.73 rear gears with E-Locker from a newer F-150 with a 5.0L with a 10 speed auto.
@Kindalouddecaf Жыл бұрын
I’ve actually priced both options out, for the trans, controller, wiring harness, driveshaft, ujoints, tuner and credits for a 6r80 swap vs the 5 speed and everything involved with that, it’s about the same price. But, the 6r80 definitely be quicker.
@kermitefrog64 Жыл бұрын
I have a 2005 Mercury Grand Marquis LS and it is a great car. The first modification I have made was changing my headlights to Fahren LED's. I also put in a transmission oil cooler and have gone to Amsoil for the transmission and in the engine. I would not go to the 4:10 gear ratio. I had this in my 1964 Ford f250 and I finally went to a higher gear ratio and it improved my MPG and ability to to faster than 55 mph. My next addition is putting in an Amsoil remote bypass oil filter.
@callmegeorge3 жыл бұрын
I actually live about 20 minutes from the shop that the Marty Tune comes from. It’s neat to be so close!
@D.D.REAPER3 жыл бұрын
Marty is a good dude he calls you to set up everything . he does awsome work with VICS and mustangs. Ive known him for a year or so . I love near tucker Ga so its sort of a drive for me lol. But worth it
@callmegeorge3 жыл бұрын
@@D.D.REAPER if I can go right to the shop it’d be a great experience and seeing some of the pics on Facebook I really want to see some of the cars in person
@Red_Proton3 жыл бұрын
You have great info on the awesome Crown Vic. Thank you!
@pantherprojects12953 жыл бұрын
I'll finally be uploading my 2 03' Mercury Grand Marquis builds and the story about the 2 car's and bringing them back to life... Hey keep up the hardwork and the bumper looks awesome!!! I bought a new bumper for my white 03' but just the factory bumper Lol... Stay safe and stay blessed... #SemperFi 🇺🇸
@rockrivera53392 жыл бұрын
I got my tune from Lonnie over at Blue Oval Chips. Love it! Other mods include 3.55 gears and Trac Lok rear end. 80mm maf sensor off a mustang, trickflow plenum, Ford Racing intake manifold. Underdrive pulley system. Dual exhaust with glass packs
@pvrpleswxg4 күн бұрын
Do you have a link for the gears and trac lok rear?
@rockrivera53394 күн бұрын
@@pvrpleswxg I found mines on eBay. If you get a used one like I did. Make sure you get new clutches, preferably the carbon fiber ones.
@iihdofjfodsd3 жыл бұрын
Marty tune is 110 percent worth it .I changed my rear gears to 4.33 and a detroit tru trac n man its a whole diffrent car ,.lol
@tjohnburton2 жыл бұрын
How is it on the highway
@SlikLizrd Жыл бұрын
@@tjohnburton It's f**king LOUD, and it eats gas like crazy !!
@hotrodlincoln7186 Жыл бұрын
How bad is your top end speed and how bad is the gas mileage now?
@jayydee60243 жыл бұрын
Damm i really want that front bumper!!
@mariodr203 жыл бұрын
Just buy a marauder lol
@jayydee60243 жыл бұрын
@@mariodr20 nah im good with my p71
@chrisharding28132 жыл бұрын
@@jayydee6024 no you're not. You like Krabby Patties Squidward.
@yeanah25712 жыл бұрын
@@mariodr20 who has $30,000 for a CVPI with DOHC head, floor shifter and an ok stock exhaust?
@chucktaylor86322 жыл бұрын
I want one 2
@baird5776mullet3 жыл бұрын
I did the 93 Oct Marty tune, new plugs, MSD coil packs, K&N filter thanks to your video's, even though it has the 327 rear end it runs, shifts and performs so much better now, T.Y., hope you have a meet somewhere in S. Alabama or NW Fla sometime.
@baird5776mullet2 жыл бұрын
@Mike Mike Johnson08, I also did a total cat delete
@jasoncooper31163 жыл бұрын
I want a Marty tune bad! I'm loving watching you and BST build your rides. Keep up the good work bro!
@benjaminnichelson153 жыл бұрын
only 505$
@jasoncooper31163 жыл бұрын
I know, but the house needs stuff more than my car. I'll get one someday.
@jasoncooper31162 жыл бұрын
@Mike Mike Johnson Google Mo's Speed Shop and give him a call. I think he sells you a tuner and loads a tune custom taylored to your car before he ships it out. If you have the tuner, he will sell you a tune and email it to you so you can load it onto your tuner...I think. I still haven't done it yet. I did get 4:10 gears. I highly recommend that too!
@terryduggan322 жыл бұрын
Only $170 if you get a un-married used tuner. I bought my sct x4 for $100 from a buddy.
@eriv4735 Жыл бұрын
Except Mr. Random doesn’t actually build ANYTHING..BST on the other actually turns wrenches and knows what he is doing
@dionrau55803 жыл бұрын
That guy did a really good job on the bumper.
@linwoodavenue43003 жыл бұрын
3.73 gears and a J-Mod are a good combo for us ‘98 to ‘04 Panther owners. You still get good low end power without sacrificing so much at the top end
@Trap_Or_Die_842 жыл бұрын
How much horses would you get from that set up?
@linwoodavenue43002 жыл бұрын
@@Trap_Or_Die_84 0 hp gain. But you free up about 20lbs of torque at the rear wheels
@tomcatmcgillicutty69132 жыл бұрын
3.73 are kids stuff,,,4.10s at least...And no you don't "lose top end" like the meatheads claim
@linwoodavenue43002 жыл бұрын
@@tomcatmcgillicutty6913 you’re not the first person I’ve heard say that 🔥👍🏽
@tomcatmcgillicutty69132 жыл бұрын
@@linwoodavenue4300 They say that because they're too scared or don't wanna spend the money to try them out.... And they listen to other morons who've never tried them either and want to justify it but saying omg imma lose milage
@mjnation1883 жыл бұрын
I want that front bumper! That’s sick!
@Elite02k2 жыл бұрын
My 2011ffv p7b has an e85 Marty tune with 23lb injectors, ford performance fuel rails and intake, the k&n drop in, 3.21 to 3.55 lsd swap, upgraded fuel pump, custom built lightened aluminum driveshaft, shift kit with a trans rebuild, Marty also adjusted the shift points after the trans was back in. Smaller pulleys with a spare belt to swap to when I want to have the most of it on the pedal. I went with an inch wider tire on the rear and I run mid 13s pretty consistently. 13.417-13.710 were my highest and lowest times since the current build was finish. Haven't dynod yet but I'd hope it atleast has 360 to the wheels
@souldude63442 жыл бұрын
Could you link the rails and intake please? I’m interested in making some gains myself
@Skellyrm2 жыл бұрын
You must be loving these gas prices.
@Elite02k2 жыл бұрын
@@Skellyrm let's go brandon!
@eriv4735 Жыл бұрын
You’re probably making 240 at the wheels
@Skellyrm Жыл бұрын
@@eriv4735 common 15% average drivetrain loss. Stock the 2011 is 239hp So that 203 at the wheels stock. Now factor in the bolt on's and the tune. Only real way to know for sure is a Dyno.
@patricksmith9262 жыл бұрын
Damn I just watched the last video man you made me get a panther you make some great content
@paulshamblin62602 жыл бұрын
I like the bumper cover on the white one.
@dennismese2363 жыл бұрын
Great stuff as always!
@Mapp2004 Жыл бұрын
On my 99LX, before it was hit by a texting driver, K&N CAI, BBK 78MM throttle body and plenum, 373 with T-Lok, super chip 93 octane tune, O/R mid pipe and Magnaflow dual exhaust. Love and miss that car.
@CtheDead209-zt8tj2 ай бұрын
All that money for 5-10 hp max lol....
@streetbeefsanyday82722 жыл бұрын
Damn these cars are too cool. I’ve owned brand new cars and trucks before but this car is just too cool!
@cz-bundy68963 жыл бұрын
I was just changing the plugs on my Vic 5 min ago... I'm definitely a Chevy guy.. the plugs on These cars are ridiculous lol. I only own this because it was 700 bucks and I don't have to put miles on my $30k Silverado lol. But I do love this car. But it's a reg crown Vic with the 2.76(or whater) rear end 🤢 😂, it literally shifts into 3rd at 87 It's my hoopty g ride lol.
@Haph_hazard3 жыл бұрын
Tryin to keep the truck nice for the next guy?
@cz-bundy68963 жыл бұрын
@@Haph_hazard no just have 3 mouths to feed and thanks to good old joe my truck now Costs 50% more to drive. The 6.2 and a Biden administration = weekend only truck
@normanduke88553 жыл бұрын
@@cz-bundy6896 the President has nothing to do with the price of oil. Biden got Covid under control. That's big.
@cz-bundy68963 жыл бұрын
@@normanduke8855 oh god... when did the 'vaccine' come out? Before Biden ... But I'm going to choose to keep my other comments to myself. But what was the average price of gas last year? Or the average before the pipe line shut down? Yeah not even close to now so have fun enjoy your singer in chief. I won't be back to even look at your comment.
@Haph_hazard3 жыл бұрын
@@cz-bundy6896 You realize the president has no say in the gas prices right?
@shamirsims1 Жыл бұрын
In my old grand marquis I chromed out the throttle body put dual timing chain and advanced the cam also a expedition intake and radiator
@RougeLex Жыл бұрын
Nice! Great work in composing the video thanks for the information. Where can I get a bumper like that Cobra-style bumper for my crown Victoria???
@joeysimmons27793 жыл бұрын
U forgot about the rear bumper tie up to decrease drag.
@TaylorMadejdm19752 жыл бұрын
Im interested can you explain..?
@joeysimmons27792 жыл бұрын
@@TaylorMadejdm1975 Mr random he said if you tie the rear bumper it will decrease drag more aerodynamic system under car you should check him out bro Mr random
@eriv4735 Жыл бұрын
Holden It’s called a “bumper zip tie” mod and you can find it on forums relating to these cars
@Elver_Galarga_jugo2 жыл бұрын
I don’t see anyone manual swapping for $400, you’d be lucky to find a T45/TR3650 for $600 and you’ll still need a clutch and flywheel that’s gonna run you another $200 or more and even then, still need the peddle assembly, quadrant and cable. You’re looking at at least $1200 just in parts.
@minutemanproductions80293 жыл бұрын
Congrats on 100k subs!
@derrickbrooks2919 Жыл бұрын
I didn't think u can use the Marty tune and the cam shift together. They both plug into the same port. So how do u get them to work together or is it just one or the other??
@michaelberna9872 жыл бұрын
The 4.10 gears should be paired with a limited slip differential if your car doesn't have one factory.
@chrisdiaz76153 жыл бұрын
Love your vids man. Good to see a fellow Cuban and panther platform lover
@floridarossi9111 Жыл бұрын
If you remove that air box extension that stick out into headlight area will change the tone of the car and helps.
@chrischery2733 Жыл бұрын
Start in 2003-2011 crown Victoria, grand marquis, and town car are my favorite car,
@ericrojasvelez8891 Жыл бұрын
I got a question...do you know what kind of coilovers will fit my 2003 grand ma.....I was wondering if any other car will fit...like what year mustangs if mustangs coilovers fit
@n.b.p.davenport70662 жыл бұрын
Did you do the major Weld Repair on the frame where the air conditioner condenser drips down on it and Rust. 😖 that whole Corner out, you might want to look underneath that car frame real well
@Tours-DIY-Reviews-HowToDo Жыл бұрын
Where did you get the front bumper with fog lights, any links?
@ragintaurusmusclemercury70233 жыл бұрын
I will stick with my Jones Flow Pack Mufflers and rear cats delete. The advantage of living in Texas. You can get away with it here. I just bought my Grand Marquis back in December. My goal is to make it a Marauder tribute that it should have been. 350 hp cammed 2 valve 4.6, trans shift kit, 2200 stall converter, 3.55 rear gears, aluminum driveshaft, and 2 inch lowered suspension with cross drilled rotors on 18" wheels.
@oldschoolrican Жыл бұрын
I got a 1997 Mercury Grand Marquis & so far I installed a Throttle Body Spacer & I can feel more horsepower.
@harrison4ever1253 жыл бұрын
The tr3650 IS a tremec 5 speed. Also if you think you are going to do a tr3650 swap for $400 you are insane. Short of finding a wrecked Mustang GT in the junkyard and only using the parts off of that car, the swap is going to run the average person closer to $1,000 if you do it yourself and install a new clutch set. Don't forget that you're going to need some serious fabrication knowledge.
@alexplowski5523 жыл бұрын
I'm no rocket appliance, and I figured it out. But, Yea, your right, costs way more than $400
@kdcxsh10752 жыл бұрын
Another popular mod in Dallas tx is to have your throttle body n intake (new intakes only for crown Vic’s) ported , both together is like 500
@kdcxsh10752 жыл бұрын
Can like get real good throttle response n hp gains can be from 15-20
@gabrielphilp323210 ай бұрын
How would replacing the air filter with one that isn't any bigger (thus having more surface area) increases the horsepower? Not to mention you didn't change the size of the throttle body, or any of the intake ducting.
@runningraggedranch50863 жыл бұрын
I was just looking at 6 liter caprice fro 07 to 2017 man nice caprice but they got a sweet under the back turbo kits for the crown vics
@ambush85022 жыл бұрын
Where?
@michaelbruh91733 жыл бұрын
Whats wrong with the Marty transmission tune? & only the engine tune can be chose to be ran?
@MayhemMechanic2 жыл бұрын
Another one I would suggest is getting getting an old interceptor computer out of a junkyard. When the old Crown Vic interceptors bought the farm and went to the boneyard, they still have the same police computers in them.. I bought 1 bought at a junkyard years ago out of a 98 Crown vic and put it in my 99 grand marquis. Instantly instantly changed transmission shift patterns for the better, and removed the governor speed limiter.
@breadwinnermolicker9375 Жыл бұрын
Hey I did the same thing but it’s just my transmission shift not right
@MayhemMechanic Жыл бұрын
@@breadwinnermolicker9375 Did you have transmission issues before? Or did it start after you plugged in the Interceptor computer?
@breadwinnermolicker9375 Жыл бұрын
@@MayhemMechanic no not before but now it’s not shifting right
@breadwinnermolicker9375 Жыл бұрын
Where it’s located
@MayhemMechanic Жыл бұрын
@@breadwinnermolicker9375 Where is what located the pcm?
@heftys133 жыл бұрын
what kind of aftermarket valve Cover set can u put on 2006 Crown Victoria Engine
@miamimagicians2 жыл бұрын
Wow I love that front bumper where did you get it
@radicalizedonline68253 жыл бұрын
Where can I get that dad gum cobra front bumper ...got a 2011 P7B I want it on!
@Whats-It-To-Ya3 жыл бұрын
Choosing the right cam and headers will get you more power for less money than this list. +20 for a tune on a V8 engine isn't that great. The secret to cheap speed has always been weight reduction and gearing. I could easily get this car down to 3,000 lbs without even trying. Add some 4:10 gears, you'll have a much much quicker car that handles a ton better and stops alot better too. K&N filters suck, you need an actual Cold air intake to benefit from anything like that.
@aidankirby84122 жыл бұрын
How much for Cam/Headers do you think?.....Cheers
@phenom40232 жыл бұрын
How u get rid of weight without taking away interiors looks?
@Whats-It-To-Ya2 жыл бұрын
@@phenom4023 remove the sound deadening and insulation under the carpet. Then ditch the spare tire and jack. Could replace the front seats with lightweight racing seats. That's about it for the interior without making it look bad. The real weight reduction is under the car and the hood, along with fiberglass front clip. My first weight reduction mod on any car is a/c delete and sometimes power steering delete. On some cars you'll even gain a few horsepower that way, but not always. Lighter wheels are a huge benefit too, if you are willing to spend the money. I'm just scratching the surface here since there's alot of weight reduction tricks you can do without making your car look bad. It's basically free horsepower and it improves the life of your engine too because you are moving less weight. The key is to figure out what you want to do with the car and how far you want to go with it.
@dramaface2 жыл бұрын
Dude, you are so off. You could get it to 3k lbs, huh? Even if you removed the entire engine it would still weigh over 3k. These cars weigh 4,100 lbs, boss, taking a spare out and putting lightweight wheels is moot point. And 20 hp for a tune isn’t a lot? Dude, what are you talking about? That is great for a horsepower:price ratio. “K&N filters suck, you need a cold air intake.” The crown Vic comes with a cold air induction box already. A k&n filter would flow much better than a paper filter. You just seem to be talking without any real data about these cars.
@p71nero2 жыл бұрын
@@Whats-It-To-Ya even a fully race prepped one of these cars still weighs over 3500 lbs lmao
@CAROLDDISCOVER-FINDER252511 ай бұрын
👍 I've tried k&n not a fan. But you do have some interesting suggestions. I still own a half a dozen of these cop cars. Always looking for an idea but I don't chop them up anymore
@midgetmayo2 жыл бұрын
Just commenting for the algorithm. I really like my 3.27 ratio , everybody is always suggesting those 4.10 gears but they'd be Shite on the highway .. If I could actually get a manual swap done for $400 , that would've been done a long time ago .. You'd be hard pressed to even find the parts for that price. No hate.. just not sure I fully agree with this video , I've been wanting a Marty tune for a hot minute now , I'm sure I'll get there.. Cheers.
@jayjay71602 жыл бұрын
Ive been debating on 3.27 or 3.55 right now I have 2.73 what would you suggest? I'm not worried about gas mileage I just want a smooth cruiser with more low end
@instinct90382 жыл бұрын
I have a question ! Can u put a 04/08crown Vic cluster into like a 98/99 Vic ?
@ericouellette5293 Жыл бұрын
I just got a 01 grand marquis LS. I am surprised by how well it moves for a 4,300 pound car. It's faster then my POS 01 Silverado with the 5.3. Mine is loaded up only option it doesn't have is the steering wheel controls for the radio and climate control. Got it for 800 and it had 113,000 on it. I want to mod it some but have to fix my POS 01 Silverado for winter first. Just absolutely love my car great ride, good power and gas mileage.
@frankammirati3385 Жыл бұрын
I paid way to much for my 04 grand marquis , really burned my ass knowing I could have Purchased one way cheaper but I was in desperate mode and needed something right away , every time one would turn up cheaper I couldn’t get to it thanks to the wonderful fucked society we live in now a days .
@eriv4735 Жыл бұрын
Are you including yourself when you say the car weighs “4300” lbs? If so that makes sense as heaviest model marquis in 2001 weighed under 4000lbs
@ericouellette5293 Жыл бұрын
@@eriv4735 yep that's with me in the car yet I weight only 140.
@eriv4735 Жыл бұрын
Eric Ouellette Do you have 180lbs of dumbbells in your trunk? The heaviest marquis weighs under 3975 lbs so you have to have a lot of extra weight in your car
@1bmudkcuf462 Жыл бұрын
@@eriv4735 Lmao gotem
@maxcactus72 жыл бұрын
Any chance we can get some dyno numbers showing which of these mods ACTUALLY increase performance?
@eriv4735 Жыл бұрын
This guy probably doesn’t even know what a dyno is 😂🤣
@chrismadison8786 Жыл бұрын
What type of Front Bumper is that, and what did you pull it off of???? Thank you so much!!!
@MrRandomReviews Жыл бұрын
i made a video on it
@runningraggedranch50863 жыл бұрын
Look for the single under back of car hidden turbo kit they sell with all all the parts to install on crown vics
@ambush85022 жыл бұрын
Wait What?
@harrison4ever1252 жыл бұрын
@@ambush8502 yeah check out the brand STS. They've been doing rear mount turbo setups for many many years. And read this for the pros and cons: www.carthrottle.com/post/the-advantages-and-disadvantages-of-rear-mounted-turbos/
@abrahamsalazar37343 жыл бұрын
What about the ported elbow from adtr thats like 300 bucks and will give you power unlike most of the mods here. or even a bigger throttle body or both
@NickThePilotUSA Жыл бұрын
Why doesn’t canshift work pre 2005? What parts are needed to make that work
@drakeshriver23163 жыл бұрын
So if I want to get canshift and Marty tune at the same time. Should I tell Marty not to mess with the transmission tune? I’m basically asking if the canshift will handle all the transmission tuning work?
@issaissa28032 жыл бұрын
What is the canshift please more details
@tonyaltobello6885 Жыл бұрын
@@issaissa2803 watch the video??
@slightaimbot81123 жыл бұрын
Important question: Can you do all this to a grand marquis?
@roywebb31493 жыл бұрын
I hope so, lol
@cardinaloflannagancr89293 жыл бұрын
Yes though really not without looking further at what is involved with some of the mods.
@b85douglas2 жыл бұрын
yeah when he popped the hood it looked just like my 05 grand marquis
@mickeymang62 жыл бұрын
99% the same car bro
@joserivera91222 жыл бұрын
Absolutely same care except gears and intake I ordered a used tuner and a cvpi intake now I’m find a way to get a trac loc and 4.10 gears and when it’s done ima get my custome tune from Marty
@gaggikmartirosyan115 Жыл бұрын
any advice to what engine i should swap in my 05 CVPI?
@saadkhaled40292 жыл бұрын
I really want that front bumper too
@MrTommy2Tone12 жыл бұрын
Where did you get that front bumper. I need that.
@treyosborne93252 жыл бұрын
I have 06' VIC LX SPORT I CAN'T WAIT TO DO THIS
@babiboib72 ай бұрын
Im wondering how did you get those fog lights fixtures/mods like that?
@YipperX5 Жыл бұрын
Filter, makes sense, thinner package and better flow is one step to more power. The tune is obvious, I canr wait to get my marty tune! But I am doing more improvements first. Gear swap, obvious advantage over the 327's, hate losing that top end speed though :( swapping to a trem 5spd and 410 in the rear would be sick! (Don't be a baby, diy! Its easy if you never have to open that transmission. Not being able to use a can-shift for my 03 makes me so sad!
@fecklarjenkins25492 жыл бұрын
Sct tuner $340 does engine tune and tranny shift points no tune shop required . Love mine
@MrRandomReviews2 жыл бұрын
i used to say the same until i saw one go up against a marty tuned vic. the marty tuned vic won that race on two identical p71s head to head....thats what sold me
@user-un6hj4hl7w3 жыл бұрын
can this canshift be used with the used with the marty tune?
@user-xi2ob9qy4e3 ай бұрын
I know im hella late on this but couldnt I just swap to a 2005 ECU In my 2001 and make the CANSHIFT work?
@brandoncotton8550 Жыл бұрын
What tuner should I get for my 03 marauder?
@whatsreallygoingon2532 жыл бұрын
You can get 4.10 gears from early 2000s ford explorers out of the junkyard super cheap they have 3.73 also
@jasoncooper31162 жыл бұрын
That's what I did too.
@74keefg632 жыл бұрын
Did those rear end mount up or did you guys take the gears out and swap them out
@whatsreallygoingon2532 жыл бұрын
@@74keefg63 gears out and swap unless you got welding skills
@whatsreallygoingon2532 жыл бұрын
@@74keefg63 bst ford channel has a video showing you how to find the right ones
@74keefg632 жыл бұрын
@@whatsreallygoingon253 none at all ...I don't even trust my self to swap them out lol
@MrJbeaste8 ай бұрын
Where did you get your feont bumper with the fog lights?
@vermontvermont92922 жыл бұрын
Jesus, I come from the VW world. Im picking up a mint 1997 merc tomorrow. These mod prices are MUCH cheaper than what im used to. Im certainly doing a 5 speed swap.
@rttt15912 күн бұрын
Just so everybody knows the 16v 4.6l V8's top out around 400-450 horsepower before you blow your bottom end so you may want to consider engine swapping or a serious engine rebuild if you're thinking about throwing in a twin turbo or something insane. You could rebuild it but the whole engine would have to be rebuilt with forged internals and a forged block.
@cky4sk8r1443 жыл бұрын
Do any of these work for 2004 crown victoria lx
@brandonsmith-qw6pz2 жыл бұрын
where can i get one of those front bumbers?
@DEVOTED2YaHUaH144k2 жыл бұрын
Im a huge fan of the crown vic!
@olafvikingwarrior23493 жыл бұрын
Where you get that front bumper?
@jmsmikey2 жыл бұрын
What tire specs are you running ~ I'm looking to max my footprint & you look like you've got it maxed out! Thanks
@SlikLizrd Жыл бұрын
For maximum performance AND longevity of your tires, it is important to match the TIRE width with the RIM width -- The TIRE width should be NO MORE than 85% of the RIM width. Source: Pirelli Tires of Italy
@beskiiugh7376 Жыл бұрын
Where did you get your front bumper off your white Vic
@berkeley5104 Жыл бұрын
Would my 1999 ford crown Victoria pass smog with the Marty too let me know asap
@jaquited89562 жыл бұрын
Did you spray paint the grill?
@NICK-qn1dn3 жыл бұрын
Dude is fkn awesome!
@larrydemby79133 жыл бұрын
can use a K N cold air intake on my 009 cv 4.6 thanks
@ridinsolo1158 Жыл бұрын
Knowledge is priceless
@dreadnoughtprime63013 жыл бұрын
My only question is whether or not doing a muffler delete/bypass will set off a check engine light. Of course, I gotta replace my O2 sensors first, but still, it has me curious.
@RodknockRhett2 жыл бұрын
I doubt it as long as you leave all of the O2 sensors in it's place. My Town Car's exhaust is leaking right at the flanges and there's no codes for emissions or anything related to the O2 sensors.
@dreadnoughtprime63012 жыл бұрын
@@RodknockRhett Found out once I got it done that it would only matter if I took out a catalytic converter. The straight pipe sounds fantastic.
@Blake-ww5bo Жыл бұрын
In CA I don’t think I’ll be able to pass a smog check, what do you think about adding electric cutouts?
@mytrigger5613 Жыл бұрын
@@Blake-ww5bo i think the idea is to get your smog, then go nuts, but save everything cause in 2 years you'll have to put it all back together to pass. Or, if you head into the guts of certain city's, I used to take my VW Bug and I would pretty much give the guy $100 bucks then walk across the street to give him privacy and I think he entered my info then ran the test through his legal car to get the pass and away I went. This was over 20 years ago, i don't know if it's possible anymore. If it's old enough it doesn't have to pass smog, but I don't know what year the cut off is currently. Newsome and the dumb dems are nullifying our votes. We're not really a blue state, neither is Georgia or Arizona. Tyranny is wide spread. This smog garbage is BS
@09tahoeppv3 жыл бұрын
Dam that rim defender big af 😂😂
@The_Tactical_Wook Жыл бұрын
god that sounds workable. I want it all. I want to give my 09 cpvi its growl back!
@hotrodlincoln7186 Жыл бұрын
Mmmm, I believe the jms Pedalmax is alot better then the canshift. The jms pedalmax doesn't increase hp or tq. But, it allows you to access full power of your car on tap. The only draw back is if you have a heavy foot like me you'll only be getting like 8 to 14 mpg aka smg.
@dylanedmonds71963 жыл бұрын
Is 93 pump gas required for the Marty Tune ? Or is that just the name of the tune? And would it work on a 99 Marq?
@sethcrowther18683 жыл бұрын
It can be for 87, 89, and 93 octane I believe. Not certain about e85 but maybe that too
@TheJimmyBuffalo3 жыл бұрын
@@sethcrowther1868 He does e85 tunes.
@sethcrowther18683 жыл бұрын
@@TheJimmyBuffalo oh I thought you’d have to change fuel pumps or something for that
@TheJimmyBuffalo3 жыл бұрын
All 2008+ were flex fuel (e85) ready from factory
@concededsleet08983 жыл бұрын
Marty can tune to your desire specs you want. But for e85 would more likely need to be 05+ since they have the specific requirements to run e 85 without mess up your vehicle unless you got the kit to make it e85
@GoonieLord3 жыл бұрын
I've never seen so much work into a Crown Vic
@Joesfosterdogs2 жыл бұрын
I heard the PI cannot handle the K&N filter due to tuning....also it gets oil on the MAF....how long have you had this and any issues? these vids are entertaining but many times do not give true reviews for lack of performance time to ensure actual quality
@eriv4735 Жыл бұрын
Some cars need a tune with the k&n and some don’t..I’ve run k&n filters for decades and over a million combined miles and have never had any issue with any “oil” on the maf..sounds like user error to me 🤷♂️
@ChiefRickyRC2 жыл бұрын
Got nice coil packs...that was good buy
@p7bspinning5213 жыл бұрын
Cmon now Mr random I love your videos but your not getting 8-10 hp gains off deleting a muffler or even the cats. After you delete them even with a tune to take care of that exhaust delete maybe half a hp. I don’t think people realize how much of a difference u feel at 2-5 hp let alone 10
@whoamitoday63923 жыл бұрын
I bet you do get 8-10. Factory exhaust was a lot more restrictive back then
@cardinaloflannagancr89293 жыл бұрын
Yeah that's very hopeful gains and I believe he said rear mufflers one time then rear cats another. Then there's resonators on a civilian will gain about nothing but sound.
@eriv4735 Жыл бұрын
Who am I Today? No not really 😂🤣
@sucha603boy8 ай бұрын
You can actually run 4.56 gears also without issue on the highway. The transmission’s overdrive is so tall that it’s still putting at highway speeds
@trevordon8192 жыл бұрын
+5 hp from changing the air filter? Out of the 12K or so I've put into my GM, the Marty Tune is the one thing I would absolutely not be able to do without. Even with that said, there's no way you're getting +20hp from a tune, Marty or not lol. This guy is either smoking Jupiter Dust or has no idea about Panthers
@eriv4735 Жыл бұрын
This guy has a bunch of teenage followers that hang on his every word and no he doesn’t know much about cars in general
@ant.sn9543 Жыл бұрын
@@eriv4735 so u d-ride him in my comment where i gave you numbers to prove you wrong, but wanna say hes wrong in other comments 🤦♂️😂 u a troll 🧌 fam
@Simon_Michael20022 жыл бұрын
Can u put a link to where I can find the 4.10 gears the whole set ?
@knitres2 ай бұрын
The canshift is a great way to blow up your trans good job. They are not made to handle manually shifting like that