The ULTIMATE ONE Performance Angle Grinder. Parkside Performance PPWSFA A1 vs. PWSAP E6

Рет қаралды 42,113

Күн бұрын

Пікірлер: 57

@zvon8294 11 ай бұрын

Best model, PWSAP 20Li D4 (with switch), is not available on German market any more,but maybe still on Czech or Polish markets? I'm using first model PWSAP 20Li B2 for over 3 years and it still works as on first day. When it is new, it's necessary to open gearbox and fix secondary bevel gear to shaft by Loctite, add grease a little, and it will last forever. I did it on mine and one brushed Parkside cordless angle grinder. That's my advice for any new angle grinder.

@BrokeLifeEU 11 ай бұрын

PWSAP 20Li D4 = speed select feature and actual physical button = best way to do an angle grinder!

@thePavuk 6 ай бұрын

I had D4, died after few hours. I used about 1mm of cutting wheel when electronics burned. D4 is not available in CZ too. These new membrane switches are No-Go.

@BrokeLifeEU 6 ай бұрын

@thePavuk I just got a D4 for a future video I hope it lasts 😅

@arturho7 10 ай бұрын

I have a basic question, because this information was missing in the video - what capacity were both batteries set to? Because it has been proven that it has a significant impact on the device's performance. And more importantly, did they both have the same setting?

@BrokeLifeEU 10 ай бұрын

I have never connected these batteries to an app. I dont like the tool and app combo. I just like to use them as they come. So both on default setting. They have no more than 10 cycles each.

@fabiomilazzo7467 10 ай бұрын

can anyone please tell me at what RPM the disc rotates on speed mode 1? what is the lowest RPM it can spin at?

@BrokeLifeEU 10 ай бұрын

I did test them, but did not include the footage in the video as it was not good. I hope I have not deleted it. I will try and find it and will let you know!

@dakata17819132 11 ай бұрын

at least i will be waiting for one with a proper switch, not membrane with a sticker

@BrokeLifeEU 11 ай бұрын

Once you are done with cutting with this systwm you spend just as long looking at it trying to figure out how to turn it off. Don‘t fix what isn‘t broken Parkside…

@abandonedbucharest7704 11 ай бұрын

For how long can you cut with the 8ah battery?

@BrokeLifeEU 11 ай бұрын

Not too long. Every cut you see in the video I had about two attempts at. After that the batteries were down a bar. They were fully charged to begin with. And if having to use on of these on the last bar of battery they would not have as much power. So I‘d say about 15 cuts from this caliber and you drop a bar on the 8ah.

@abandonedbucharest7704 11 ай бұрын

@@BrokeLifeEU damn, they have to invent a 15ah battery for this grinder🤣

@BrokeLifeEU 11 ай бұрын

Haha, would be too heavy. As if they used the puch type cells the batteries would be too expensive. But an 8Ah is honestly fine as long as you have too and won‘t be grinding for the entire day. In that case just use corded.

@DragonlordSVS 4 ай бұрын

@@BrokeLifeEUA 12ah would be fine, it isn't as if it would run a lot of cuts anyway for the weight to matter, which weight tbh wouldn't be half as much as the 8ah since the weight is not increasing quite linearly with the number of cells. Heck personally I wouldn't have a problem with a 15ah either since I never run Li batteries of any brand bellow 1 bar. As soon as 1 bar pops it's time for battery switch or taking a break/doing something else, except if I really have to finish this particular job right now. Btw some named top brand do have 10ah+ batteries too.

@postelnicuadrian72 11 ай бұрын

If you don't any stall issues, keep it in speed 5 or 4. It will not stall!! At least A1 will not.

@BrokeLifeEU 11 ай бұрын

I did want to test their limits sort of. There is a huge RPM difference but in my hands they felt identical in terms of cutting and grinding power. In terms of stalling it was also pretty much the same. On sale for €50 if you have 8Ah batteries lying around they should be alright. Can‘t compare with a corded though!

@paraskevas8880 3 ай бұрын

The newer flathead, the A2, have updated electronics and is more powered from the previous A1.

@BrokeLifeEU 3 ай бұрын

Spot on, the A2 is even better than the A1. Quieter as well as more powerful.

@Azcane 11 ай бұрын

Great review! I'm going to buy the E6. But I'm curious: does it make a difference to use 4ah (smart) batteries instead of 8ah, in terms of power? I don't own the bigger ones and I'm unsure if I really need them

@BrokeLifeEU 11 ай бұрын

Thank you! Yes, on speed 6 you need an 8Ah battery in order to use it fully. And run time is a big plus on the 8Ah battery. I feel the 4Ah batteries lose a bar as soon as they are on the tool. In any case an angle geinder is a very power thirsty tool so at 4Ah you won‘t get too much done, but if you have multiple 4Ah they should be enough for smaller jobs.

@marcingyver9839 10 ай бұрын

Cześć😊 wczoraj kupiłem mimo oglądanych testów model e6 i mam baterie smart. Na filmach ludzie pokazywali że urządzenie zatrzymuje się przy malutkim nacisku i że nie nadaje się to do cięcia grubych rzeczy. Dzisiaj zrobiłem test na 4ah smart i uciąłem 10x pręt gwintowany fi 10 oraz pręt stalowy fi 14 uciąłem 2x. Po tym wskaźnik przeskoczył z 3 na 2 kreski baterii ale byłem zdziwiony bo nie zatrzymała się na tym ani razu🤔. Gdyby tylko była bez awaryjna to sprzęt pierwsza klasa jak na bakteryjne urządzenie czasami coś uciąć. Kupiłem w lokalnym Lidlu a na polskim allegro model ma same pozytywne opinie i nie wiem dlaczego na sklepie Lidla dużo osób narzeka że słabe może widocznie zależy jak się trafi. Ale no nie chwalę dnia... Wolałbym jedynie mechaniczny włącznik. U mnie na 4ah wszystkie prędkości łącznie z 5 i 6 działają poprawnie 🤔

@BrokeLifeEU 10 ай бұрын

Cześć! Gratulacje! Bardzo miło to słyszeć! Dla mnie potrzeba trochę presji, żeby się zatrzymać. Bez ciśnienia lub z małym naciskiem jest ok. Ale jeśli je popchnę, E6 zatrzymuje się przed A1. Ale nie ma różnicy w prędkości 5 i 6, jeśli używam 4Ah. Tylko jeśli użyję 8Ah. Dziękuję za podzielenie się swoimi doświadczeniami! Życzę wszystkiego najlepszego z nowym narzędziem!

@marcingyver9839 10 ай бұрын

@@BrokeLifeEU jeśli masz baterie smart ustaw w nich prąd rozładowania na 2.8 v bo jest fabrycznie 2.5 podobno to je zabija ja od razu tak ustawiłem

@konro2155 8 ай бұрын

@@marcingyver9839Cześć, u mnie nie widzę różnicy między 5 a 6 biegiem nawet po zmianie na 2.8v.

@thugpigeon8688 6 ай бұрын

here's an idea make a corded vs cordless parkside angle grinders comparison with the new performance corded 125mm

@BrokeLifeEU 6 ай бұрын

Thank you for the idea! I will try to make it happen!

@heavoc9793 11 ай бұрын

The miss of a switch is a total non sense for a portative tool like this, especially for a "pro" way !

@BrokeLifeEU 11 ай бұрын

It feels unsafe to use without a proper switch. Difficult to switch on and even more difficult to switch off as you are avoiding the spinning disc bit.

@kiky2h 10 ай бұрын

I think that D4 is the most powerful model, but the button jumps with the vibrations

@BrokeLifeEU 10 ай бұрын

Might be the reason why they abandoned the button.

@sosik1 9 ай бұрын

@@BrokeLifeEU+1

@Dimitrije_Stamenković 2 ай бұрын

Has anyone managed to convert the stupid control panel to a normal switch? Or at least make it remember the setting. If I wait 5 minutes it resets to speed 1 and I have to go back to 6

@BrokeLifeEU 2 ай бұрын

I think your best bet in terms of that is just to get the D4 version. The last one with the physical button. Also I got a green one, it has an analogue speed control so it stays where you leave it and a normal trigger. I am also really not a fan of this membrane button stuff from Parkside. Really ruins the entire grinder...

@Dimitrije_Stamenković 2 ай бұрын

@@BrokeLifeEU Well I just bought the stupid thing

@BrokeLifeEU 2 ай бұрын

@@Dimitrije_Stamenković I have not looked around in the app, however could it be possible to change the default settings via the Lidl Home app and a smart battery?

@Dimitrije_Stamenković 2 ай бұрын

@@BrokeLifeEU Yes, with a smart battery it remembers the speed setting. With normal batteries you have to choose it every time

@BrokeLifeEU Ай бұрын

@@Dimitrije_Stamenković Not a fan of the smart battery system, because I don't like connecting tools to my phone, but at least there is an option in this case.

@nikosvaidis5397 11 ай бұрын

Thanks from Greece!!

@BrokeLifeEU 11 ай бұрын

You are most welcome! I hope you enjoyed the video and the channel!

@iuliansele4380 11 ай бұрын

Detin acest flex De la treapta 5 la 6 nu se simte nici o diferență de ce ?

@smncosmin 11 ай бұрын

Din aplicație activezi treapta 6

@BrokeLifeEU 11 ай бұрын

Ai nevoie și de o baterie de 8 Ah. Cu 4Ah nu va exista viteza 6.

@marcingyver9839 10 ай бұрын

@@BrokeLifeEUu mnie na 4 ah wszystkie biegi działają 😊

@D5244T5 11 ай бұрын

Great video as always! I was suprised to see thst the performance was so equal, i would have thought the föat head with its lower rpm would be a bit behind but no! I follow a few tool testing channels here on youtube, i have always been curious about the enormus amount of tools you lust have after making all these videos! 😳 Do you still use the powertools that you know after a test session is weaker/worse then the winning tool?

@BrokeLifeEU 11 ай бұрын

Thank you so much! It means s lot to read that you like the videos. I keeps me going and trying for bigger and better things! Some of the tools are not my own (Parkside tools). The ones from Aliexpress I buy and keep, because there is no other way to get them. After the tests I keep them just in case I come up with a new idea for the future. I do borrow tools from friends, especially for the comparison tests. In most cases they are in denial if the tool they have is not the better one. I would be the same if I were in their place. However none of us use the tools for any professional sort of use we are all the DIY sort of people so in most cases if it does the job it is good enough.

@D5244T5 11 ай бұрын

@@BrokeLifeEU Great that you can borrow the tools from friends! 🙏🏻 The Performanve series seems very good, i would say perfect for the DIY! And also i like how their tools look, not important, but an extra bonus! I live in Sweden and we cant shop parkside online from Lidl, so we have to wait for new inventory in the stores, sometimes its weeks in between until there is something intresting to buy! :/ Anyhow, glad for tve video! When i find the performance angle grinder i think i want to buy it (i collect tools, its silly but ones gotta have a hobby) but it will probably take forever until its in the shops! 😅 Have a nice day! Today im doing the impact conversion, parts finally arrived! 🙏🏻

@BrokeLifeEU 11 ай бұрын

Glad to hear the parts arrived finally! I hope the conversion goes well! And spot on I think that is the best way to think of Parkside tools that they are DIY. Snd as a matter of fact budget DIY. So in that bracket they are mostly good enough.