Thermostat Housing Replacement, Ford Mondeo Mk5 2l Diesel

Thermostat Housing Replacement, Ford Mondeo Mk5 2l Diesel
finally fitting a new thermostat housing assembly with new "o" rings and a bleed off pipe which i advise to replace at the same time
thermostat housing ford number 2 264 810
"o" rings 2 372 936
bleed pipe 2 012 849

[@jammyfeen]

My thermostat housing exploded today on my 2017 with 153K done. I knew you'd probably have a video on how to replace it and watched this while waiting for the tow truck. Thanks to you I checked the bleed pipe while waiting and sure enough it broke too. Dealer has a new housing already in stock but had to order the bleed pipe. I would have been out of action a few days longer only for your video as I'd have had no replacement bleed pipe. Tackling this job tomorrow once I have the parts. Thank you so much for taking the time to upload these videos, they make these jobs so much easier for us. Proper gent.

[@DameAndThatGame]

Detailed, tips, extra parts recommend, iv been followong car tutorials for YEARS. and your the most informative 👌

[@alan4x]

Awesome! Thank you!

[@drrnclrk]

Just want to say thank you Alan for the detailed instructions. Completed this morning on 2015 S Max. Got up at 5am to avoid heat of the day, and followed your video step by step. 😊

[@alan4x]

Fantastic, well done and saved yourself a big garage bill😊

[@berrrtie]

Alan. Yet again your very concise instructions have saved the day. Chalk up 1x Alternator and now 1x thermostat housing. Thanks for taking the time to record these videos I fear I’ll be back again to your channel for my F.ix O.r R.epair D.aily! Coffee (beer) brought via link

[@spierchips]

I wanna thank you Alan. just done this job on my 15 plate these videos are gold to people like me .my temp gauge started to creep up with no water loss then go back down fine in traffic get on a bypass open her up then the temp went right into the red an alarm came on the dash and temp drop back down stopped to check the water still full . Anyway after watching your vid change the thermostat housing following your instructions all seems well car also seem more lively, so thanks again keep doing it bud

[@alan4x]

cheers cardiff car vlogs, glad it worked out

[@spierchips]

@@alan4x lol yeah after a new radiator change also 🤣

[@spierchips]

Actually I have an overheating problem thermo and rad change ain't cured! It can run local all day take it up to motorway speeds tft gauge goes up and has even thrown engine coolant temp overheated and if you ease of the throttle temp comes back down too normal boot it again goes up again seems like no flow or blocked got fans to cut in no loss of coolant ??

[@alan4x]

@@spierchips with the engine running,,, check you have coolant flowing through the bleed off pipe from the thermostat housing into the expansion bottle...if there is no flow then the water pump impeller has fallen off the back of the pump..fairly common problem kzbin.info/www/bejne/fmS7hIunYpZ2gaM

[@dynnudragos]

hi mate, from where did u bought the tube seal 2372936?

[@MelCorpus]

My dad is a diesel mechanic, if only he is still alive, im sure he will be very happy to see this

[@alan4x]

thank you miss pinoyfan in philippines😜

[@thescallytrader]

My new Tesla will.

[@edwardkrezoek2454]

dziękuję Mistrzu . bardzo dobry film

[@jonkarlos3405]

Very amusing Alan and great video. Straight to the point no nonsense. Very thorough and informative

[@alan4x]

thanks

[@2889Daniël]

They all seem to have this housing issue, it just becomes detoriated and burst open Thanks for sharing Alan

[@pctolna]

I have to change a thermostat on my 2015 MK3 Galaxy now. This video is a great help for me. Thank you for posting this video.

[@Dark-qx8rk]

The Thermostat housing for the Ford Galaxy 2.0 TDCI 2016-2019 is the exact same part so this video is a great help. The thermostat had failed closed on my Galaxy and the coolant overtemp warning came on. The expansion tank had bubbling water right to the top and the thin return pipe was hot. The pipe to the radiator was cold. I sprayed WD40 into the expansion tank pipe connector on the housing and got it out without breaking it by twisting it a bit while pulling very slowly. Also make sure you buy the 2 o-rings for the rear pipe (cost £12 each from dealers). The existing o-rings can get damaged when pulling the housing off.

[@antonthedaytrader]

Thank you for the video you have done. I used it step by step. What you say at the end happen to me. Glue gave way and blew it apart. $320AUD for a new thermostate $82AUD for that plastic pipe that always breaks.

[@alan4x]

yes i had loads of them come apart, bad design

[@Smartchoice_oo2]

This video is really helpful for me. He explains you everything very clearly and step by step . Thank you a lot 😮

[@alan4x]

You're very welcome

[@soonerlon]

A Yank checking in here. Even though I'd never own a Mk.5 Mondeo diesel I enjoy Alan's nicely filmed videos - very entertaining and he has some good mechanic skills. I also like seeing Alan "literally" using FACOM tools. I love my FACOM tools, but they're very expensive here in the U.S. Good luck to you Alan!

[@alan4x]

thank you

[@jonnyward2905]

⁠@@alan4x Alan i really need your help. This thermostat is the same as my mk3 Ford focus. I bought one. This video helped me fit it. But now the top ain’t opening. Anyways my question is, where does the bottom hose connect to, and where does the top hose connect to and is there anyway I could have mistakenly mixed them up? Please please please help

[@tecnaman9097]

I'm old enough to remember when all it took to replace a thermostat was 5 minutes and $10 for the part. I hate to think how much all that gear cost just to replace a f%^& thermostat. Good work guvnor.

[@alan4x]

lol

[@antonthedaytrader]

Awwaome video. I just brought a 2015 with 195kms. Within a few days mine blew off. The part that faces you when standing facing the engine and houses the thermostate. That part at the end of the video. Very expensive part as well.

[@alan4x]

yes had loads of them housing end caps blow off and yeah not cheap for a new one

[@shyhm]

Thanks for this video its helped me a lot I had the same problem and I've managed to change it and save myself a load of fees. Thank you👍👍👍👍

[@alan4x]

You're welcome!

[@dynnudragos]

hi mate, from where did u bought the tube seal 2372936? Thx

[@shyhm]

@@dynnudragos directly from ford. You can call ford motor parts with your reg and they search for the right one

[@dynnudragos]

@@shyhm thank you! How much was one? I found on ebay one for 22£.. seems bit expensive..

[@shyhm]

@@dynnudragosunder £5

[@thescallytrader]

Amazing video Alan. Mine is still leaking. Hopefully it will last until after Christmas. I might have a go at this myself although I might fuck it up. Thanks for the part numbers. Pricks at Ford Dealership refused to hand them over. Keep up the good work.

[@alan4x]

thank you

[@FreedomMatter]

Does that O-ring need to be replaced with a new one?

[@ultracleansolar]

did mine yesterday thanks for the video as i referred to it quite a bit the side hose took abit to remove and the nut at rear was fun the battery and plate need to be removed to get to this , the bleed pipe is a must mine was brittle from heat it was a issue waiting to happen

[@alan4x]

well done for that, saved yourself a hefty garage bill

[@TheDaf95xf]

Morning Alan hope your ok 👍🏻 Another great Mondingo video 🤣 If I watch enough of your Mondingo fixing them I’ll be a top mechanic like you lol 😆 Have a lovely weekend so see ya 🤣🤣

[@alan4x]

thank you

[@LaurentHOAREAU-g6f]

Thank you for this vidéo. I had to remplace my thermostat and this vidéo was very precious. I can fix it, thanks to you.

[@wallacemassey1371]

Nice one Alan. Knew her wouldn't let us down. Good vid.

[@alan4x]

thank you

[@Automotive_Solutions]

Another great video. Crappy brittle plastic - they really are designing a car to last a certain amount of time. The press at the end is a good stress buster. 👍

[@dragannesic55]

You are the best😊 Big reguard from Serbia👍

[@alan4x]

thank you mr dragan😊

[@pingu00728]

yup @ 20:15 you mention the whole end just breaks off, happened to me this morning while on the motorway. car still drove but reduced my speed for a further 2 miles before i could safely pull off at a junction. seen what it was and called a tow truck. i hope the extra 2 mile drive didn't get it too hot to cause further damage!

[@Blacktails1]

Mine blew up today 🥴 Thanks for the video Alan 👍

[@mikeuk1954]

I don't own a Mondeo but enjoy your videos Alan. 👍🤣

[@alan4x]

cheers

[@tayguy509]

Many thanks to u mate i was able to replace my thermostat kit on my focus st greatly appreciated only issue i had was the rear pipe bolt and i didnt realise i just had to tighten the bolt and the clip would just go into place many thanks for sharing ur video u saved me alot off money infact 300.00 as i was quoted 565.00 !! Due u a pint mate

[@alan4x]

Glad it helped, thanks brian

[@gerardquinlivan2991]

Hello Alan, Gerard here from Ireland. Find you videos a life saver. Im a taxi driver and I have a 1.5 diesel Mk5 mondeo 2017... Coolant loss over the last few days... topping up a small bit every other day.. Would the procedure for fitting the thermostate housing be the same on a 1.5 diesel? And how can I determine whether it is the thermo housing at fault... Many thanks for the videos over the years....

[@alan4x]

Hi the thermostat housing on your engine will be different so best to get someone to check where the leak is first

[@gerardquinlivan2991]

@alan4x ok thanks Alan

[@Mamaiataetzigan]

Excellent job! Thanks for the video mate!

[@alan4x]

No problem 👍

[@castrolgtx5064]

Fantastic video thanks for sharing Alan

[@stevetaylor3279]

Great video extremely helpful, Many thanks for taking the time to help people

[@alan4x]

Very welcome😊

[@TheDoRelian]

Keep up the good work, great tutorial!

[@alan4x]

cheers

[@DavidLodge-n8v]

Quick question watch the video replaced by thermostat but the heaters are still blowing cold do you think it’ll just be air blockage

[@gavinmurphy5758]

C Mon Big Al, give us a little tool box tour??????

[@UkraineTrain21]

Brilliant video. Have you seen these thermostats stick open? I have a Galaxy with this engine and in the winter months the engine will not warm up unless I drive on the autobahn. It seems like the thermostat is stuck open.

[@MarkWilson-qb5kr]

Great video once again Alan ,think us Mondeo owners should carry a bottle of kseal as part of the service kit as the plastic isn’t the best in these cars

[@alan4x]

i do... k seal works wonders for mk5 radiator leaks😜

[@РамисЗаитов]

Замудрëнная и не надëжная система. Чем дальше тем сложнее детали, о надëжности можно забыть. Поставьте простой элемент! Нет надо что-нибудь придумать, да посложнее, все гениально просто!

[@cpuuk]

I'm always cheered up after watching you fix a failed part :-)

[@alan4x]

thanks

[@TY-dl6oz]

Very detailed explanation. Really great! Also, just wondering, after the new thermostat is installed, is it necessary to use a diagnostic computer for configuration?

[@alan4x]

no you don't need to do anything, it will just work automatically

[@TheShortfused]

Many thanks for this vid Alan,changed mine and twas really easy after i removed battery tray so i could move the plastic turbo pipe out of the way. Twas near impossible before that :D

[@alan4x]

Glad it helped

[@TheShortfused]

Speaking of 4bolts needed to be removed for the housing to come off, but shoving 3 taken of threw me off a bit i must admit 🙂 tried to take the housing of with 3 bolts off and not seeing the 4th until i shone a light with good flashlight and realized I've spent 25mins in vain:p but otherwise spot on!

[@dynnudragos]

hi mate, from where did u bought the tube seal 2372936?

[@TheShortfused]

@@dynnudragos ordered from ford directly, if i remember correct it needs 2.

[@dynnudragos]

@@TheShortfused thanks mate! Do you know how much was? I found on ebay 22£ for one.. seems bit expensive..

[@mohammedabdurrouf8038]

Hello terbo man your KZbin blog is awesome Thanks

[@aaronsmyth53]

Is that the same set up as citroen c4 picasso 2.0 hdi it doesnt bleed pipe going to the coolant header just a little cap like a valve cap ?

[@Stereo-Vybe]

Thanks for the video.....mine was loosing coolant but couldn't see any tell tales of water pooling anywhere on the gearbox housing, I recently purchased my car so no idea of full history but it does have dealer stamps in the book and receipts for the timing belt / water pump done at 139K miles and there is evidence of thermostat related bits sat under the expansion tank (spring and O rings) so guessing it could be on it's 3rd thermostat now as it's at 142k miles and could have been done at the same time as the belt and water pump. Upon watching this video it would seem that the thermostat housing looks to be relatively new but the return pipe to the expansion tank on mine is a normal piece of 1 inch rubber tube that is jubilee clipped in place rather than the smaller pipe. (the jubilee clips are still shiny !!) I'm not convinced that jubilee clips will do the job here as there's not much for it to grip with the type of union so have just ordered that part for now and see if this cures the issue. I discovered the coolant loss issue when my heater stopped blowing warm air so popped the bonnet and as a lot of coolant had been lost I did note a bit of steam coming from around the expansion tank area so panicked and turned the engine off quickly. It hadn't overheated and the temp gauge were normal at that stage so no damage. I've no other symptoms that leads me to believe it's a head gasket issue at this stage so I were very puzzled at the water loss.....Thanks for such an informative video Alan...really appreciated, hopefully it's just the pipe!

[@NickElliottuk]

Hello from the future. Another great video - you're providing an invaluable service! My coolant temperature sensor has become intermittent. Can I replace that on its own, or do I need to do the whole thermostat housing?

[@NickElliottuk]

Turns out it was a leaking thermostat, just like you said. The expansion tank was actually filled to slightly over max, but when I removed the cap, there was a whooshing noise, and all the coolant disappeared into the pipes. I guess the intermittent temperature was due to pockets of air in the system. Just as well I didn't drive far like that!

[@DanielShannon-m5x]

Brilliant video. Does anybody have the part number for the two o rings ?

[@trexxx65]

Hello Alan, I have seen your video and I think it is great,, to change said thermostat, first congratulations for your videos are of a great help, to repair our mondeos,. Well I tell you I have a mondeo 2.0 tdci 180 cv, 80000 km, I have observed that the level of antifreeze a little, and that has had lost by the area of the gearbox,, I do not observe the leak to which you refer in the box of the thermostat, no liquid, I understand it would be an internal malfunction of the thermostat, and open to change it, or it would only be the gasket of the same thermostat to the butt, I hope you can help me,,,,

[@ianroscoe8427]

Thank you Alan watched your video and managed to fit my thermostat on my 2016 focus st today but just wanted to ask if you know the part no./ name for the pipe from thermostat to the expansion tank as the clip has broken like youve mentioned? Regards Ian

[@sheffielduk3428]

My 2011 kuga 2.0 tdci gets up to 90 after only 1 minute of driving then stays there all day never over heats, never had a car get warm so fast

[@mdyatesy]

hi Alan, would this be the same process for a 16 plate Galaxy ? the temp goes up when working the engine and down when not working it, very little fluid loss and its gathered around the area you showed in your top top video, what are your thoughts please.

[@s3bby513]

FORD GANG YES LAD keep the posting up

[@alan4x]

cheers

[@grahamevans9606]

A big shout out for the Mk 4!!!!!

[@mikewilliams235]

Hi Alan, great video, I have fitted the new one and the temperature doesn't over heat but now the heater isn't getting hot. As any ideas?

[@mikewilliams235]

I wish I watched the video about the over heating mondeo first, as I just did the test of taking the bleed pipe off and checking that it pumps water out. Water pump it is then 🤢

[@alan4x]

yes if water does not flow out of that leak pipe with engine running then the impeller on your water pump is detached and spinning freely which is not circulating the engine coolant

[@younesetemadi4015]

HI dear , good and nice job , i love your teaching for mondeo replacement, just i have one question : ford mondeo 2015 diesel is same thermostat housing and location?

[@robbob2861]

I had not a common situation with my thermostat. It didn't leak and the top hose wasn't so much hot as I thought it would be, the only not good sign was that the car was warming up very slowly. I had to drive about 12miles to get the engine hot. I wasn't sure if the thermostat was wrong or maybe something else, because usually when a thermostat doesn't close, the top hose is getting hot quickly but in my situation it wasn't even much warm to think it can be this issue with constant open. I took a risk and I've replaced my thermostat. It turned out that it was the fault of the thermostat. Now, I need 6miles to get the engine hot in a winter weather about 0 outside. I drive with AC on for the whole year, so it was taking very long to get the engine hot. I think I would not know on summer that I have broken thermostat.

[@MoschyUnbxd]

HI, After removing everything else, stuck on the very last part before disconnecting the thermostat. After loosening the rear bracket, the thermostat doesn't seem to want to come off the rear hose. It doesn't want to twist and wriggling it up and down doesn't help. When I pull it towards me something is stopping it, making a banging noise when I try to pull it towards me but can't find anything obstructing it. Is there anything I'm missing? Have a 2017 galaxy. Also can you advise on any types of sprays to loosen this as both the rear pipe and the part that it connects to on the thermostat (where the clamp is) are both hard plastic. THANKS!

[@putbinoot]

If Carlsberg did how to thermostat videos. And I don't even have this car but looks like what I need to do on my Peugeot Boxer. Cheers for tips on O rings and pipe.

[@espidoctor]

Hi my Friend,bleeding with diag?

[@TheAriiiiii]

Thank you so much for another helpful video. I'm no mechanic but do find myself fixing my car myself just because I enjoy it. I actually have a Peugeot traveller but it's the same engine and need a bit more help if possible. The heater pipe that come out the back of the thermostat housing has a special clip and mines broke and I can't get a hold of another pipe from Peugeot since it's on back order with an unknown ETA. I've removed the clip of the old heater pipe and plan on using a reducer coupler or reducer pipe with spring type clamps, do you think that's a safe option. I only ask because I'm not sure if spring clamps would be strong enough to hold the pipe since Peugeot didn't use them for whatever reason. If you have the part number for that heater pipe it would really help so maybe I can source a used one even though the Ford pipe is slightly different I can try work with it. Also the pipe with 2 O rings, where does that go? Sorry about my massive question lol

[@alan4x]

i take it the clip is the one that holds the heater pipe from the heater matrix connection on the baulkhead to the thermostat housing..the clip holds the pipe onto the housing, i have spare clips..i can put one on ebay for you tomorrow and message you. the pipe with the 2 o rings goes around the back of the engine behind the dpf and into the rear of the engine casing which the water pump fits into..you dont want to disturb that if you can help it

[@TheAriiiiii]

@@alan4x Thanks that would be great but I would like to replace the o rings also if you have them also. I can't seem to get any parts that I need from Peugeot but managed to get the thermostat housing from a parts distributor no problem on the same day. I am also a taxi driver and this is the worst time for things to go bad for me so any help would be appreciated thanks.

[@TheAriiiiii]

@Alan Howatt Hi Again, it's actually the clip for the pipe that goes to the water pump I believe. The heater matrix pipe has the 2 -O- rings on the peugeot. Anyways, out of 2 pipes 1 has a bolt clip and one has a clip, I need that clip.

[@alan4x]

@@TheAriiiiii i am thinking your car is a different setup...can you leave me your email and i will send you pictures, there is only one clip on these thermostat housings and that holds one of the heater pipes to the housing but maybe yours is different

[@hwsascha]

Very nice instructions. Could you please let me know if it is the same for the bi turbo cause a friend of mine drives one and has a leaking problem.

[@alan4x]

yes the same engine and thermostat housing

[@hwsascha]

Thanks

[@lanehogger1532]

Hi Alan. I was working in St Neots last Friday night and saw one of your mk5 Mondeos. AF17 *** the orange management light was on. I though poor Alan 😝

[@markhochmann4032]

Hi Allan, thanks for the great videos. I have a 2017 MY Titanium Diesel Mondeo here in Melbourne, Australia. Best car I have ever owned. My Thermostat housing failed and I lost the coolant, heater stopped working but engine ok. The repair cost AUS$1395. My question is can the thermostat be replaced separately to the housing or are they one complete assembly? I ask this as the car has an extended warranty that specificall mentions the thermostat as included in the warranty. If the housing cannot be separated from the housing then I think I can and should claim this as a warranty repair. Cheers

[@alan4x]

hi mark, your electronic thermostat is all part and parcel with the housing assembly and can only be replaced as a complete unit ..hope you get your warranty as that price is very expensive

[@markhochmann4032]

@@alan4x Many Thanks Alan! Love your videos.

[@drrnclrk]

Also, i saw oil leak from the high pressure fuel pump next door to the thermostat, but that job looks a fair bit harder. Could be one i let the professionals sort out, although I am tempted to give it a go. 😊

[@alan4x]

that is a common oil leak.....it is the gasket between the cylinder head and the intermediate unit that the pump bolts onto

[@drrnclrk]

@@alan4x Yes I've watched your other excellent video on high pressure fuel pump removal, the one where you have the whole engine removed, but it looks like there could be a couple of things that I might find too difficult. Namely the cambelt cover where you remove engine mount to get access and the turbo hose removal at back of engine. Can you access cambelt cover from wheel arch instead?

[@sambothebold]

Alan please help!!!, im driving myself mad trying to find some info on the 2.2l duratorq in my mondeo. There never seems to be as much info on the 2.2 tdci. I have a low coolant temperature reading on the dash. Going to try changing the main thermostat and the oil cooler thermostat (if there is one), possibly the ECT sensor. The only thing ive managed to find is the plastic housing for main thermostat, cant find where the water pump is or where the oil cooling thermostat is!!!!

[@fahimtube6803]

Hi Alan i have ford galaxy 2016. The heater is blowing but not getting hot also on the left side coming cold air and the right side is warm but not hot. When i turn it up it goes colder instead of hot. Any idea what causes that? Thanks in advance

[@richm5601]

Hi Allan I had a leak , so we replaced the housing etc No we don’t have any heat at all Can you spread your knowledge here pls ?

[@degu5249]

Hello Alan, please help. My Mondeo MK5 T8CC will stay too hot while the cooler and heater stay cold. Water level is OK Hoses don't get hard either. No water loss. What do you think? Thank you Alan

[@alan4x]

probably water pump impeller not spinning kzbin.info/www/bejne/fmS7hIunYpZ2gaM

[@degu5249]

@@alan4x Thanks Alan, you were right. the water pump was broken. I've now installed one with a metal impeller.

[@Johaidiiii]

Hi Alan! Question for You. I replace my old leaking thermostat to new, I don't no, how is normal coolant working temperature, at moment working temp is between 95-101 degree? ?? Mondeo 2.0tdci, 2017. My friend Mondeo 2.0tdci 2015 between 89-95 degrees with old thermostat

[@kertolen1348]

@Alan Howatt, can you tell me why it has to be electronic? What was the matter with an `conventional, usual, mechanical thermostat????

[@Youtube_deleted_my_favourites]

I'm guessing the Kuga is the same, well going by the cost it will be

[@alan4x]

if its the same 2l engine as the mondeo it will be

[@jonnyward2905]

⁠ Alan i really need your help. This thermostat is the same as my mk3 Ford focus. I bought one. This video helped me fit it. But now the top ain’t opening. Anyways my question is, where does the bottom hose connect to, and where does the top hose connect to and is there anyway I could have mistakenly mixed them up? Please please please help

[@alan4x]

Hi. The top radiator hose goes to the top thermostat connection and bottom radiator hose to bottom thermostat connection. I guess it is possible to get them on the other way around

[@jonnyward2905]

@@alan4x so obvs the bottom hose should have a constant flow while the top opens at operating temp? Have you got a diagram I could use or anything just to see where the bottom hose and top hose are coming from ? Please

[@Johaidiiii]

Perfect, I changed how you did the video. Only 115 000 km 😢

[@zeez9053]

Bleeding H it’s like a military operation compared to old minis

[@alan4x]

lol

[@jcgp4147]

Hi Alan, is the puddle of water on the gearbox produced by the thermostat?

[@mikewilliams235]

Stupid question but I can't find the o rings or bleed pipe using those numbers?

[@alan4x]

they are ford part numbers, best to phone your ford parts dealer

[@thomastogher2221]

Hi Alan Where do I get parts, my thermostat is leaking and have to replace it

[@ronbaker7972]

Where is the fuse and fuse box for the Mk5 mondeo park assist module ?

[@genchobike]

Hi Alan, your video helps me a lot with the maintenance of my Mondeo mk5, thank you for that! I have a question, after replacing the thermostat, how do you bleed the water system? it only blows cold in the compartment!! Thank you in advance.

[@alan4x]

it should self bleed by itself, try pulling the bleed pipe off the thermostat housing, if not you may have an issue elsewhere

[@genchobike]

@@alan4x thank you very much for the information

[@pk8455]

hi, can I ask you question, could you tell me why temperature goes up to 120 while driving over50 miles/h on motorway and comes back to normal when slowing down. Ford mondeo mk5 2l diesel 2016 reg . thank you.

[@Mali128]

Hey nice vide ;) im belive Citroen use same ones , how much is to replace them ? Thanks

[@shaundarnbrough5824]

Hello alan do you have the part number for the o rings

[@bobthorpe1961]

Is their a part number. For the. O rings

[@sheffielduk3428]

How the F did you get that 10ml nut off the rear pipe! 2011 ford kuga 2.0 diesel on mine and i cant seem to get to it

[@FreedomMatter]

What type and specification is the o-ring on that pipe? Where can I buy it?

[@alexis162546]

Ya pas d'aptation a faire apres sont changement ? Est pour la purge quelle procedure ?

[@agentdesneiges1445]

Hello, thank you for this. I have calorstat problème in same than in the vidéo. ( 308 sw gt eat6) . Peugeot say me you need pp2000 or diagbox ti change it. Its right ? Thank you a lot for process

[@СветозарТабачки]

Hello, can you give me the number of the two gaskets where you change them in the video?

[@nunoleite46]

Top top, amazing video

[@alan4x]

thanks Nuno ☺️

[@keithrimmer3]

Hi, Alan is that the same as the 2.2 like the Freelander 2 and focus 2.2 and what are they like to work on, i got the timing belt and water pump to do on a freelander2 cheers al keep up the good work .

[@tezali9754]

Hi Alan question for you. I have a 2016 ford galaxy recently I have noticed that both the radiator fan come while I'm driving when mean they come on I mean the engine feels like if it had aircon running inside the engine, the engine bay feels like it has been sitting in minus temperature thats how cold it feels even after a couple of hours drive any ideas?

[@bkba394]

Where was it leaking from on the housing

[@motokierownik5091]

Dear Alan, could you be so kind and help with recognizing problem with cooling cirquit. Suddenly cooling temp started jumping from low to high and radiator is cold. Looks like thermostat is closed. But it has been forced to stay open and the problem is still the same. Next I think is broken water pump but is it possible? Is there any other element than can make such problem? Thanks in advance for your imput. Andrew.

[@alan4x]

hi... could well be water pump...this video might help kzbin.info/www/bejne/fmS7hIunYpZ2gaM

[@motokierownik5091]

@@alan4x Thank you very much for quick help. Kind regards

[@13rz31]

And what is the price of new thermostat? Are new one any better or do they also leak after 80k miles? Thanx and keep the good work!

[@Godfather143c]

Hi. I have a problem with this engine. After connecting the diagnostic computer, temperature sensor 1 shows a good temperature, but temperature sensor 2 shows - 40

[@ionutzis]

Could someone please tell me what is the size of the o ring ? Here in Denmark I can't find them anywhere. And the pipe I'm afraid I'll have to buy it from Ford

[@SamiSmau]

Hi Alan, I have a S max 2016 whit engine T7CL 2.0 diesel. I lost water from 50.000 km until now actually 107.000km and I never knew where. By my last refill I forgot to put back the cover back and I drove so on the motorway for 15 km whit 200km/h . When I drove out of motorway appeared the key notification and after a few meters I accelerated but the car didnt want to accelerate anymore. I hold on and switch the engine off and it never started again! I think it can be bloke sealing or EGR! What do you mean. Did you ever had this problem?

[@bkba394]

How do you change the metal pipe that goes round the back

[@VesaPekkaEerola]

Hi. Fitst of all: Great videos! I have the following problem: My temp gauge will rise if I use webasto to preheat the car before starting. But as soon as I start the temp will drop dramatically. It will start to rise slightly if I don't drive but as soon I start driving the gauge will drop to minimun. For me it sounds like thermostat stuck open but not sure. Just trial&error for a 300e part sounds costly. What do you think?

[@shahzadgujjar3335]

Morning Alan, where is the Ford Galaxy mk3 thermostat located on a 2.0 diesel 2013