How to install Mixet cartridge MXT07

[@dssales6111]

Thanks!

[@TheShackHome]

DS WOW Thank you You are the first to ever give from this video. Bless you thank you. It is my pleasure to help.

[@KarenJ-mg8vq]

I looked at videos alllll day on how to repair a spinning handle, a shower faucet that does not get hot (but the sink does). I went to ACE and Lowe's to purchase a shower stem. Out of ALL the videos I watched, it was THIS VIDEO that showed me step by step what to do, but most helpful is that it had my EXACT shower pieces. That helped alot! I didn't know about the little tab thing in the faucet handle. Once I finally realized my shower handle had one (yes, I was one of the ones who just yanked off, but had I come across this video earlier in the day, I would have known about it). anyway I unscrewed it to reattach the handle (before I knew about it, I could NOT get the faucet to work). My guess is that whomever fixed it prior to me, also didn't know about that little tab. At any rate, thanks so much. My shower is now getting hot water, the handle works! and I've returned the pieces to both ACE and Lowe's and I'm going to cancel the plumber I had scheduled for tomorrow!!!

[@TheShackHome]

KarenJ0202 Superb. Glad it all worked out and you were able to cancel the plumber and save that money. Sounds like you can treat yourself to a nice dinner out....Thanks for viewing so happy to help.

[@steep6655]

I had the same issue, but with the cold water. I like to take cold showers. And after about 5 minutes my hot water would warm up my cold shower. I turned my boiler down to vacation mode to lower the hot water temperature. I took the faucet apart today and I've reassembled it. Hopefully now I can enjoy a 100% cold shower.

[@Silentjay886]

Was looking all morning for a video on how to replace mine and ran into this very helpful and easy installation video!!! Thank you so much for this!!!

[@TheShackHome]

@@Silentjay886 my pleasure glad it helped thank you for viewing

[@phoeniciacloud1515]

Thank you so much. 😊Just now seeing this in 2023 and this has been so helpful. I’ll let you know how it goes 🙏🏾

[@TheShackHome]

Phoenicia Cloud my pleasure, I do hope all went well.

[@robertisaac8041]

Thanks for your contribution to the hard working middle class people who don't have the funds to pay for plumbing services but are willing to learn from experienced people like for yourself. This was an excellent tutorial video which I put to good use and got the MXT07 replaced on our shower. Much appriciated! Robert

[@TheShackHome]

Robert this mean a lot Thank You.I always say people can do more than they realize if they gust take that step with a little guidance. It's my honor to help.

[@johnjohnson1146]

Watching and learning in 2023. You've given me the confidence to tackle the job myself. A thousand thanks!@@TheShackHome

[@teagar3]

Thank you soooooo much for this video. A year ago, I went to Home depot, and the sales guy matched up the valve, but apparently the wrong valve. I got it in ok, but turning the valve on and turning the mixture valve was a choir. This morning I watched your video, went to Home Depot with the P/N you indicated, MXT07, and followed your instructions, and now it works like a charm. Good Video....

[@TheShackHome]

You are very welcome. If I can help just one person it is worth it. Happy to hear you were successful

[@b20banthony909]

My water keeps driping why 😱😱😱😱😱

[@FrankiesWorld]

You saved me time and lots of money. Just replaced my cartridge today because the old one was leaking. Thank you!

[@TheShackHome]

My pleasure Frank good job and thanks for viewing.

[@greencertifiedweb]

I live in a 115 year old building with a lot of hard water... They guy who sold me the valve recommended rolling up a washcloth soaked in vinegar, sticking it inside the pipe and letting it set for an hour or so... I did that, cleaned it out real nice!

[@jangrigsby7480]

I have one of these 'vintage' valves in my dulplex rental home. I replaced the valve a few years back, but have never been able to adjust the temp easily over the past years. . . . .and it has been a hassle for my tenants. I will be replacing the valve once again, and thank you SO much for the very well done video and suggestions for matching the valve with correct unit. . . . and clear procedures with professional and detailed steps! You obviously know what you are doing, and are helping many older folks with your attitude and caring work!

[@TheShackHome]

Jan Grigsby thank you for the kind words. That day may come when you'll need to replace the complete valve. these are good but very limited to the accessories for it, even for a rental. this was one thing I did when I renovated my rental near Huntington Beach (In 2010) I replaced all valves and updated to Moem. I'll be doing the same when I renovate 2 bathrooms in my house. Sometimes a little extra is worth it in the long run. Thanks for chiming in and thank you for viewing.

[@jangrigsby7480]

@@TheShackHome Thanks for the upgrade advice!!

[@eliasdiez9896]

You’re awesome in explaining the right part and keeping us from making a mistake. You’re a good teacher, thanks.

[@eliasdiez9896]

I don’t remember changing this part 2 years ago

[@americanmeteoritefan9670]

Watching this now after finding a puddle under the shower area of my mobile home and narrowing the source down to my shower valve. Let it go so long because it was silent! The only thing I noticed was a small amount of mold on a wall about a year ago and it never reappeared. Looks like my weekend taken...I will be fixing the leak! Thank you so very much for this video!

[@TheShackHome]

American meteorite fan well I hope all went well and didn't take too much of your weekend. You are welcome and thanks for viewing.

[@alaluv99]

I was going crazy trying to find out which valve I had. I was about to give up, then I found your video. I have the same one, thank you for the video.

[@TheShackHome]

Adriana L. you are very welcome I am happy to help.

[@midsyntax]

This helped a lot when our shower wouldn't shut off this weekend. Wiping with a paper towel got out a screw and bent washer that were still inside after I took out the old cartridge. Don't skip any steps.

[@DutchBoyd80]

Thank you Shack. Your video helped me immensely. Every morning, taking a shower was a really horrible experience. It would start off the day with a dark mood, hating my shower. I finally decided to change out the cartridge, and watched at least 6 other videos besides this one. Yours was the one that really helped me out. Now, every time I step in the shower, I feel a sense of pride for repairing it myself. You are really helping people out, Shack! THANK YOU.

[@TheShackHome]

DB that is great. Its so true. people can do more than they realize. They just have to take that step of faith get out of their comfort zone and they will surprise themselves, Congratulation on a job well done and thank you for viewing.

[@kolinken9524]

Excellent video. Especially how he describes the differences in the two Mixit Cartridges. I also like the fact he cleaned everything (especially the on/off knob and hot/cold water leaver) prior to putting them back on. Regarding the white sealant around the Eustachian.. there's 2 schools of thought. One is to seal it as this gentleman did. However the 2nd school of thought is by sealing it any water caused by a leaking valve won't be able to get out and will ruin the wall behind. This is a similar thought to sealing a toilet to the floor. A good method to clean inside the water delivery pipe is to use an old toothbrush. While he uses Plumbers Grease to grease the inside of the water pipe and the Mixit Cartridge.. most DIY people won't have this. One can use WD-40 which is fish oil based and won't hurt either the rubber O-ring or any component. One can also use K-Y Jelly which is glycerine based and water soluble. If you wish to save money and do it yourself you can simply pull out the old cartridge and clean it. Use quad ought (0000) steel wool on the Eustachian and Bonnet nut to clean them. Use WD-40 and an old toothbrush to clean the plastic Lever and Knob. Use WD-40 and a paper towel or soft (lent free) cloth to clean the Plumbers Grease off of the Mixit Cartridge. You'll note that over time minerals in the water causes the Plumbers Grease to become sticky. This is why I prefer WD-40 or K-Y Jelly. You can also completely unscrew the Cartridge and use a toothbrush and WD-40 to clean all the threads... then simply reassemble it. Use the 0000 steel wool or 120 grit sandpaper to clean the brass rings which go onto the Cartridge. Many times all that is wrong with the Mixit Cartridge is that the rubber O-Ring is bad and letting water leak... this and the sticky old plumbers grease. You can simply buy an assortment of O-Rings from Harbor Freight Tools for $5.99 here's the link: www.harborfreight.com/225-piece-nitrile-o-ring-assortment-67677.html Simply put on a new rubber O-Ring and reassemble according to this gentleman's directions. I've saved a lot of money by cleaning all the Mixit cartridges in my rentals this way. Note: WD-40 means Water Displacement 40. It was invented in San Diego in the 1950's for the aircraft industry and military. They needed an product to displace water and stop parts from rusting and corroding. It took them 40 times to get the ingredients right.. and the basic ingredient is fish oil.

[@efrentaeza3535]

I think you meant escutcheon. If you watched how he applied caulking on the rim of the escutcheon, you would see that he did not apply any on the bottom part. That is to allow any water from a leak that accumulates behind the escutcheon to flow down to the drain below. I have seen a similar video and the plumber said to position the hole on the stem with the red mark on top not below. Which one is correct?

[@leslie4212]

Thank you! because of where I live, calling out a plumber costs a fortune. I did this all by myself! And it took no time at all.

[@TheShackHome]

Leslie you are very welcome That is why I do this you can do more than you realize. Great job thanks for viewing.

[@jerrymestas1231]

I haven't replaced this in 20 years, so I finally found a video to help me. Yours was awesome!!!! Thank you, for refreshing my memory

[@richlarsen4278]

After 30+ years of living in this house, we were the first owners, I always thought the dumb plumbers had plumbed my shower backwards. After installing the new cartridge per your instructions (red dot down) it works like it should, so yes the red dot direction does make a difference. Also, the new O-ring must have been a bit larger and I could not get it to slide in. I got a small deep socket so as not to be hitting the brass stem (socket resting on white plastic) and tapped it in with a hammer. Thanks so mcu for the video.

[@RandyLinares-f6u]

Loved it, did this project about 20 years ago and it worked but not right now it works properly, thank you.

[@denisesoto9723]

Thank you. Because of you I am able to fix my faucet and save money by having someone else do it.

[@laisanielson]

THANK YOU THANK YOU - we couldn't have figured out how to fix our leak if it wasn't for you! This video was so informative & helpful showing every step of what to do. You're the BEST, thank you so much!!

[@TheShackHome]

Laisa Nielson I'm humbled. You are very welcome.

[@laisanielson]

Ok, so somewhere I messed up, because turning it on & off has been an issue, ha ha. And so I took off the handle - it's an old one, so I'm wondering if I need to buy a new one, and I turn the shower on & off with the pliers. But now, I'm noticing that the copper piece is disappearing - is that when it's on Off position or have I messed it up somehow?? 😬

[@dougpeters1625]

Best mixet cartridge replacement video by a mile. Fantastic tutorial

[@TheShackHome]

doug peters thank you I'm humbled. I hope it was helpful and thanks for viewing.

[@AdamBBomb]

I followed these instructions exactly. The red dot went down. (Opposite of box instructions) great video!

[@gsxr750moto]

I was was thinking that this guy is giving incorrect instructions since he says red dot goes down as opposed to going up as noted on the box

[@robertsnyder2411]

Can’t thank you enough. The first time I installed this valve (based on other videos) it worked poorly then self-destructed after three months. I installed a new valve after watching this video and wow what a difference. It’s all in the details. Among other errors I think I had way over-torqued the valve the first time. I wish you a wonderful life and please know you are appreciated! And yes indeed the red dot goes down.

[@foodrusshow]

The intruction from the box said the red dot goes up. I don’t know why they don’t correct it. The company mixet should watch this video .

[@phuongmai94]

Thank u sooooo much!!!!! I’m 25yo and a female and I’m soo happy I did it all on my own with nobody’s besides your video of course! Jsut saves me $300. I literally got a quote today from a plumber and told me it was going to cost $295 to change the cartridge I was like well let me think ability and let me try changing it myself again. A friend tried changing it and realized he didn’t install it properly and didn’t push it all the way in so it was leaking, And so I nudged it a little bit and it went all the way in. I’m sooo happy!

[@marigut]

I watched 3-4 videos besides this one, and this video was by far the best. I appreciate the details and how you compare the wrong cartridge and the list of tools supplies needed. THANK YOU! You gained a new subscriber!!

[@TheShackHome]

Mari G you are very welcome and thank you Mari I am truly great full to you for subscribing. I very happy my video helped. This is exactly why I do this. Not for the masses but for people just like you. If you have a question even if not related to a video if I can help I will who knows I may make a video on it.

[@marigut]

The Shack Thank you! How about a video on replacing a shut off valve for toilet?

[@piistheword]

Nice video! Very thorough and descriptive. Left me with no unanswered questions! Thanks!!

[@julianazaragoza4998]

Thank you thank you!!! Your video gave me the courage to attempt this myself! I did it! I had a freak out moment when the water kept coming and all my turning didn’t help! I decided to take it out and start from beginning. I went straight to comments in case the same thing happened yo someone else…someone said that it came “open” and sure enough as soon as I compared the old one to new one I found my problem. It’s so smooth and easy to use now. 👍🏼

[@Asphaltsquadron]

Yep, I bought a "similar" cartridge at Home Depot. It "looked" identical. Very long story short, I went to Lowe's today and got the MXT07, 10 min job total and all worked out perfect! THANK YOU!

[@TheShackHome]

MrAsphault your very welcome. Glad it all worked out fine. thanks for watching.

[@tomjoht]

Thank you for making this video. It worked well for me and I didn't have any trouble. My cartridge was MX-1 and it fit fine. I really appreciate these DIY videos, as they help novices like me. I had a plumbing accident earlier this year that caused a flood and required $9k to repair, so I was hesitant to do anything more myself again (it's like I had plumbing PTSD). This little success helped rebuild my confidence.

[@TheShackHome]

Tom thank. You and I’m glad to Help. So true its one step at a time then your off running. I’m honored to help in the small steps. Job well done. You did great.

[@tomjoht]

@@TheShackHome Thanks. BTW, re the cartridge fit, I spoke too soon. It turned out to be super hard to turn. I tried 3 different cartridges (Mixit, Danco, Ace). None fit correctly. Decided to hire a plumber to replace the Mixit valves with Moen valves. To save money, though, I did cut holes in my drywall to facilitate the plumbing work. That was also a new and kind of tricky experience for me.

[@TheShackHome]

@@tomjoht Unfortunately that is the final outcome in some cases. There are time a new cartridge just won’t work and its time to update. They don’t last forever. Sorry to hear it was a more costly endeavor.

[@bertdeguzman9785]

wow! you are seriously a life saver! I have a home inspection coming up this weekend for my buyer of the house, I did a thorough inspection by myself and noticed that my guest bathroom was leaking from the knob.. i was about to call a plumber to take a look at it but decided to go on KZbin route I'm glad I did! only spent $60 total for the stem, shower wall trim kit and the shower valve opener. I could've spent few more hundreds of $$$ if it wasn't for you. your video is amazing and i love the detailed explanation of the steps. keep up the good work!!!

[@TheShackHome]

bert de guzman Thank you. If I had $5 for every person this helped I could of retired off this 1 video. That is why I do this is to help. not profit. I know people can do if they just try. I'm very humbled. Hope the inspection went well. thanks for viewing.

[@crash1995ification]

Your video was awesome!!! Thank you. I had the identical valve and my shower valve was hard to turn and really had to be cranked to shut the water fully off and when you ran the shower a lot of water poured out the tub spout still. I took off all the old parts and took them over to a local plumbing supply store (they are more helpful and knowledgeable than at Home Depot) and they helped me get exactly the right replacement parts and your video walked my step by step getting the job done efficiently, which is a rare case for any of my DIY projects.

[@Vista114]

Thanks for the video sir. This was my project today. It wasn't simple at all but because of your guidance, I managed to finish and complete the job, saved me big bucks from hiring a overpriced plumber. Thanks again and keep up the good work.

[@TheShackHome]

Vista114 you are very welcome and congrats on a job well done. Have a night out or just have a cold one with the money you saved. Thanks for viewing

[@ChristinaQueenHeart]

Did my research and fixed it myself in 30 minutes or so. Plumber estimated $200. I tell you, KZbin professors are underestimated bc my KZbin education is treating me well!

[@robhtp3817]

Very well done. Thank you. This Vid is step by step which is very helpful for us non-pro DIYers

[@40redfox40]

Just watched your video, ran to Home Depot for the parts and plumbers grease and will install tomorrow. Having the exact problem you spoke of...my 89 year old mother in law u able to adjust the water because it is too hard to turn. Thank you!

[@TheShackHome]

40redfox40 you are welcome i hope it all went well. thank you for viewing.

[@40redfox40]

The Shack it worked out perfect. Lived here 25 years and first time I changed it out...should have done it years ago. Thank you.

[@kathynorris1183]

I have three mix it valves I need to replace.two of them I can't even turn with two hands! Your video was SO informative, I'm confident in changing them out. Thank you so much.

[@TheShackHome]

kathy i know you can do it. Just make sure you get the correct ones. when you pull the old ones out set then next to the new and make sure they are the same. I'm happy to help thank you for viewing.

[@patrickbolton540]

Thank you very much for this video!!! I followed all the steps and tips. The most useful were using the MXT07 and the plumbers grease. It made everything go smoothly. I highly recommend using your videos.

[@TheShackHome]

Patrick Bolton It always humbles me to hear this. I'm so happy you were successful. You are very welcome and thank you for viewing.

[@markanderson3201]

This video saved the day. It is also well very well done. I did not replace my valve but seeing this video I was able to remove the gunk freezing the hot cold arm up. and reinstall it in the correct fashion. And wallah now I can adjust the hot and cold again easily. thank you

[@kathyschlesselman1520]

You helped me IMMENSELY with this video! I had a plumber out to do this for me only because I was unable to loosen the nut. When he finished he said it was "not much better" and I should tear open the wall and replace the valve. I KNEW they don't really go bad, only the cartridge. So, I went to Home Depot and got the correct cartridge. Sure enough, he had installed the wrong cartridge. You mention at about 5:05 on this video that you wished you had a picture of the difference in the two cartridges. I have one for you all! New cartridge, greased up and installed and it works like new. (Was completely unable to turn it prior to this, AFTER plumber left.) Can't seem to share in the comments, I will try to get it to you. Thanks again!

[@TheShackHome]

Kathy Schlesselman Thank you. I don't think I can post a pic in the description and I would have to redo the video to put it in. One of the down falls with KZbin. Wish that would change we could update or correct thing without completely redoing the complete video. Although I might add a link to a pic for side by side of the 2 cartridges, You could email me direct and i could try to do that. Again thank you for the comment and thank you for viewing.

[@kathyschlesselman1520]

@@TheShackHome , if you can send me your email address (I don't see it here) to [e-mail], I'd be happy to send you back the pictures. Thank you again!

[@olenaerhardt7725]

Thank you for the great film. I installed today a new stem MXT07, following procedure described. The only thing, the stem didn't go till the necessary position, though I cleaned and applied the plumber grease. I used a muffler hammer and knocked on it, it went in the pipe. Actually many people complain that the stem doesn't go in and think that it is a wrong one, thought it is that muffler hammer which is needed to complete the project. I also added a new handles set. Looks great! Thanks a lot again.

[@brendacomrie6622]

Makes sense to me. Thanks for the info. I so happy you set me straight. So now I don't have to stand on my head anymore with my tongue in the most awkward position in a gallant effort to ensure the seal is contiguous and complete all while trying to see under the damn things. What a relief!

[@robdgonz]

Red dot actually goes up. IIRC, it also says "up" in tiny print. He does it right but doesn't say it. Do not put caulk on the lower 1/4. It allows it to drain if water ever got trapped.

[@kathynorris1183]

I used to work in plumbing years ago. I have some good skills. Just never installed a mix-it, thanks again.

[@1BAYB7783]

Thanks so much for posting this. I needed to replace knobs in both bathrooms and one cartridge. This was super easy to follow and very helpful

[@gp3p89]

Your guidance through this process is greatly appreciated. Couldn't have done it without you. 🙌😊

[@TheShackHome]

GP3 p no you take all the credit I hopefully just gave some guidance you did all the work. congrats

[@RicardoOrtizReyes]

Excellent video, don't know why I stumbled into other videos first which were giving wrong information or not specific enough. Thankfully, I found yours and was able to get hot and cold water from my shower. It wasn't too easy as the circumference of the back part of the replacement cartridge was a tiny bit bigger (unnoticeable to the bare eye) than the old one. I ended up replacing the plastic washer located on the back with the one that came on the new one and using the whole old back part on the new cartridge.

[@TheShackHome]

Recardo your a true handyman. You did just what most fo us would do and fix it how ever it needed fix'n good job.

[@jimashman6251]

Very helpful video- thank you! I almost hired a plumber to fix my leaky valve, but your video convinced me that I could fix this myself, and I did. And installing the replacement cartridge was actually pretty easy, thanks to the detailed instructions and info from this video. One point to emphasize that I am not sure if it was mentioned or not- the cartridge comes from the factory in the "Open" position. Turn the valve to Closed before you test the water line for any leaks, or you will be freaked out like I was when you turn your water main line on again, and water comes gushing out of your faucet. And note that you will have to turn the valve about 50 times to get it to the Closed position.

[@TheShackHome]

Jim this is exactly why I do this. People can do more than they know just need to step out and give it a try. Of course you need to be comfortable doing so but you are the perfect example of those who do and are successful. Thank you Jim I truly appreciate your comment and viewing

[@evasquez909]

Thank you so much! I was at my aunt's house and had to replace the cartridge and this was a lifesaver

[@TheShackHome]

Eduardo Vasquez I am so thrilled to have helped but YOU did all the work congrats. thanks for viewing.

[@speckvan]

What if my valve stem continues to rotate. The hot and cold. Doesn’t stop at any point left or right.

[@ihsankhan7503]

Hi thank you so much sir .i fixed my tow bathroom because i watched your video God Bless you

[@the1000j]

Thanks a million, sir! I would just add the o ring rubber is a bit round so I used the rubber Mallet to hammer it in gently and worked well!

[@randymiyake8036]

Excellent video. Straight to the point. Thanks

[@aserrano179]

years dealing with this problem looking for the right parts and thanks to this video just fix my shower. thank you very much it was so helpful.

[@Manalive77]

You're the BEST! Saw many of these, many sub-par, but yours is the very best of the bunch!. I watched several times to be sure, then badda-bing-badda-boom--I did it! SO happy you made this video!

[@TheShackHome]

Allen that's a humbling comment. Thank you. I never consider myself the best there are many truly great plumbers out there but I've been blessed with the ability to do a few things and through that if i can help others......i'm happy to do so. Thank you again and thank you for viewing.

[@anthonyvaccaro3626]

Excellent video,easy to understand, made the repair manageable. Thank you

[@TheShackHome]

Anthony Vaccaro Thank you sir, you are very welcome. Thank you for viewing.

[@khale7180]

Thank you, I have the exact valve stem which is not common and this video helps tremendously.

[@TheShackHome]

Kha Le you're very welcome

[@michaelwise2881]

Thanks man I really appreciate that you took the time to upload this. I'm a bit of a handyman but I'm not very experienced in plumbing. After watching this I feel very confident I can replace the one in my in-laws house.

[@c19crazyhorse82]

This video is amazing, I would just like to add one more thing if there's a plumbing supply store near you I highly suggest you go there because they should have the actual mixit cartridge that comes with a brass fitting on the back, instead of the plastic ones that come from Home Depot and Lowe's. Also make sure you tighten up that screw on the back of the cartridge. After I installed mine it worked for about a week and then it wouldn't shut off. After taking it apart I realized the screw and gaskets were left inside the valve along with three other screws and three other gaskets all the way in the back from previous cartridge replacements.

[@angelcfireworks9016]

That happened to me too just now I , I shit the water off took the cartridge out and the water was still flowing out the pipe , I look inside and the screw that goes on the back of the cartridge had fell off and was stuck inside the pipe , I put the cartridge back in and took it out again and the screw came out of the pipe , I put everything back together and tried it out, hot water was on the left and cold was on the right idk how that happened 🤦🏻‍♂️

[@MrJojo2go]

Hi in 2022 soon 2023 this vid helps me thank you 👍🏿😷👍🏻🇨🇦🇵🇭🇺🇲

[@TheShackHome]

MrJojo2go my pleasure. Thanks for viewing.

[@seanbradley2153]

FYI to all... The instructions on the back of the package state to install with red circle/ dot pointed up. Not sure if that makes a difference or not. Narrator here said “down”. Also, make sure you use the plumbers grease and not putty. Use it liberally and it will slide in like is shown in the video, otherwise, you may need a rubber mallet to get it seated up to the brass-plastic-brass stop point.

[@markyg1970]

I used ky.

[@MegaTHOB]

It does make a difference, With the red dot down, hot is on the right. With the red dot up, hot is on the left as it should be.

[@MichaelCugudda]

I bought the MXT-07 original OEM post 1968, and it wouldn't fit. It got stuck, wouldn't go in all the way, unless you hammered it in with a soft mallet. I returned it and bought the Danco cartridge for Mixet part# 88200, and it fits like a glove. I also replaced the handle and plate (trim kit) with Danco trim kit (4 1/2 flange) for Mixet.

[@timothyhorn2650]

Great video! Now to go and change the cartridge in our shower. Thanks for posting!

[@ZurHoll]

This is a great video and our home greatly appreciates it. Changed the master bath shower component and works perfectly. Now on to the next project. Greatly appreciated.

[@TheShackHome]

ZurHoll i am truly humbled thank you. I'm happy to help. Good luck on your future projects and thanks for viewing.

[@andyfisher4042]

Best video and good 'tricks' for this type of valve. Gave me the confidence to do it myself!

[@TheShackHome]

Andy this is exactly why i do this. I'm so glad you did it yourself. People can do more then they think. Just need a little helpful push sometimes. Thank you for the kind words and thank you for viewing.

[@80morningstar]

You sir, are a gentleman and a scholar👍😎thanx 4 posting!

[@kenjpretell]

Thank you Ray. Excellent instructional video - it helped me to fix our shower (after I removed the stuck valve). Best Regards, Ken

[@TheShackHome]

kenjpretell you are very welcome happy to help.

[@ymararma]

I have that same shower valve that just snapped! What a god send❤ thanks

[@TheShackHome]

ymararma my pleasure. Thankd for viewing.

[@Danielpryorat60]

Thanks for the video. Last time installed was wrong part. Had to take a file to the thing to get it in. Never worked right. Also, the instructions had to be printed in so many languages there apparently wasn't enough room on the package to complete them. Nothing to say in what order the washers were to go. Nothing about the red dot. The schematic was useless, even with a magnifying glass.

[@TheShackHome]

Danielpryorat60 you are welcome great comment and thank you for viewing

[@Tiredgeek]

Brother! You gave me courage to continue my replacement. Will be trying it out tomorrow morning.

[@TheShackHome]

Tiredgeek wish you success and thank you for viewing

[@Tiredgeek]

@@TheShackHome I replaced it! Works great :) Thank you again.

[@TheShackHome]

@@Tiredgeek you are very welcome.

[@Eascoaster]

Great Video, I would like to add that the red dot to suppose to face upwards and a side note to help people out would be to loctite the screw because apparently they get loose and you will lose the screw in the pipes.

[@ThereseElizabeth671]

Eascoaster Great advice. I just assumed the screw was tighten. I lost my screw in the pipe when we replaced it. Any ideas as to how I can get it out? Or just replace it?

[@Eascoaster]

@@ThereseElizabeth671 the best answer is both. I was able to fish out one from the pipes in one bathroom and the other bathroom it is suck somewhere in there that I can't see. If you need to use another screw then use the old from your replacement.

[@WxCat1962]

Thank you! I replaced it with a new one exactly like you said, but it was still hard to turn the hot & cold handle. I found out that if you loosen the chrome cover sleeve, that goes on the main pipe over the cartridge, a little bit at a time (not loose) it will turn easier.

[@coastalbreeze7323]

YOU ROCK!! 5 STARS ALL THE WAY!! I was so skeptical of doing this for the first time on my own at 9pm on a Saturday night, hoping that I didn't have to keep the water off until a Plumber could come fix it on Monday. Watched your video like 3 times, went to Lowe's to grab the parts, came home and installed it. Only thing that was a little concerning, the valve fits, works great, like butter moving it. the old one slid right in/out, the new one required a little tapping with a wrench and then it slid in, I did clean out the inside of the pipe a lot before putting in the cartridge with Plumbers Silicone Grease. Should I be worried that I had to tap it in? It is 1988 original valve to the house. I just don't want a quiet leak dripping down the walls or something to the downstairs and taking out the the drywall. Again! You are a lifesaver! And I truly appreciate it! Shawn

[@TheShackHome]

CoastalBreeze73 you are very welcome and thanks for taking your time to view. The cartridge should slide in you shouldn't have to tap it at all. Its been enough time has or have you seen any dripping at all? If the tub or shower sits all day in the evening just feel around the handle and area see if any wetness if all dry you should be good.

[@LOWLABORUNION]

thanks for the video... so theres 2 different models.. the best bet is to take it out and check to see if you currently are using a brass backing or a plastic one.. use the same one you have👍

[@danielbentley3230]

Thanks for your know how man! I did buy the wrong one and researched because I knew it was wrong to force it in!

[@platinumsilvergreen]

Thanks i was able to replace it myself due to this video! Got replacement at lowes.

[@bicstone]

Just changed my shower stem. Thanks for the help

[@TheShackHome]

david stoneits my pleasure thank for viewing.

[@RobertoRosarioFerreira]

Great video! I finally was able to fix my shower after months of it not working properly!

[@arrowspaceman4658]

Wow, great video. We had the wrong valve as well. Sucks how they are so similar too. Thanks for making this!

[@TheShackHome]

ArrowSpaceMan You are welcome. Happy to help. Thank you for viewing

[@DavidRodriguez_2790]

Thank you sir for guiding me much appreciate it

[@ozinvesting6517]

This video helped me a lot, thank you very much!

[@TheShackHome]

OzInvesting you are welcome and thanks for viewing.

[@StelBBQ]

Great help!!! I really appreciate this video. It made the repair so much easier having the knowledge going into the task!!! Thanks again!!!

[@MySetDancer1]

Good video. Make sure no paper debris is left behind due to wiping out the unit. Always take the original cartridge to the store to make sure it is the correct one if you do not already have the correct part number. Often a drip is caused by the washer on the end of the cartridge decaying. But note, the rubber washer in the end (held in place by a screw) is non-standard in size, meaning that you can not buy a replacement at Home depot when the valve starts to drip. But you can buy one a little too large and sand it down in diameter and it will fit. But it must fit very snugly or it will leak. Don't sand it any more than necessary. A soft rubber washer will not do the job as it will leak. I can not stress these points too much.

[@TheShackHome]

MYSetDancer all great points thanks for the suggestions.thanks for viewing.

[@mvmv5883-e3g]

I had a professional plumber doing it. Two visits a week apart. First visit, he removed the part, ordered it. Second visit he tried to install the cartridge, it didn't fit, so he combined parts from existing cartridge and the one he ordered , rebuilt it and installed (wasn't easy). $289.00.

[@TheZygomaticus1]

Thank you for sharing your wisdom sir! Liked & Subscribed! Going to fix my broken shower knob. Well explained & You made it look super easy. God Bless you.

[@corteszzful]

Not gonna lie I like this guy a lot I was one of the ones who had a flood didn’t know tried to learn 😜 but thanks to this bid got it 😈

[@TheShackHome]

Thatdatezz Thank you I so happy I could hel. Thank you for viewing.

[@yuriruiz9216]

This was very helpful like your instructions and that you show and say what cartridge to use. Thanks a lot. Question: How can I loosen up the nug it is too tight and hard to take off? ... How can I get more cold water than hot my temp gets more hot than cold? The previous plumber made to get more hot than cold and it gets pretty hot so in order to get warm water I need to turn on the water all the way open. He just said I messed up on the cold water your going to get more hot than cold and didn't fix it.

[@TheShackHome]

Yuri the temp issue may cure itself with a new cartridge. if a wrench wont work calcium build up will make it hard to undo. try some WD-40, Liguid wrench or B'laster. They are penetrating Catalyst should help you. might also try a pair of vice grips for a better hold on the nut.

[@goldenrist]

Thank you so much! I was looking for the same type of set-up that I have and I finally found you. Thanks so much!

[@TheShackHome]

goldenrist you are welcome Thank you for viewing.

[@theresam1649]

I agree with you about the Mixet valve, I need to replace it with a more durable valve. Thanks so much for your reply!

[@Actionfiguresarefun]

Man your video was perfect. You saved me a lot of money. Thank you 🙏🏻

[@TheShackHome]

SJA you are welcome. I'm happy to help. Thanks for viewing.

[@Tmanaz480]

LOL... turn this nut and remove the cartridge...but first, turn off the water main. Just kidding. Great video. Now I know what was wrong with the one in my old apartment. It was too tight, and the hot and cold seemed to change strangely when you adjusted it. It wasn't just reversed. It was random and wonky.

[@neometero]

This really helps, just changed the old stem in my home, thanks a lot.

[@TheShackHome]

Leon you are very welcome and thank you for viewing.

[@OGVYpuRR]

Other than your advice about the red dot, this was very helpful.

[@rstevenhanson]

My instructions for the MXT07 say the red dot must point up. Is that what you're seeing too?

[@oktoberfest1810]

Thanks so much! Helped me with my shower valve.

[@TheShackHome]

Brett you're very welcome. I'm honored it helped

[@0rizz]

Replaced it twice in under 3 months. Happened on two properties. These valves/brand really suck.

[@TheAttitube]

My Mixet mxt07 clearly states “red mark on stem assembly must point UP” not down. Purchased 3/9/18.

[@misturchips]

Red up means temp knob flag is down; Red down means temp knob flag is up. Personal preference.

[@CalvinKleinManzano]

TheAttitube yup the red should be up i install mine today 2-27-29

[@Higgy007]

@@CalvinKleinManzano 91 years wow! Now that's a quality part!

[@kathyschlesselman1520]

I used to always change these out myself, but last time I couldn't get the nut off on one shower, so I had a plumber come out and do both showers. The master one is easy to turn again, but the hall bath is really not much better if at all. The plumber told my boyfriend the whole valve in the wall probably need replacing. Both valves are the same age and get the same usage. I don't know what cartridge he put in since I wasn't home. I have a friend who said this happened to him and he took a sanding drum bit on his drill and gently smoothed out the part of the pipe where the cartridge engages the valve and it works great now. Any harm in my trying that? It would make sense that with my hard water, it could just have a lot of deposits making it hard to turn. I swivel the master bath one daily (to all hot while waiting for hot water to get there), but my roommate just leaves it in the middle and never turns it. So I am thinking maybe it got buildup in there.

[@newmirror850]

Video a great help but according to accurate instructions on package "Red mark on stem assembly must point up." I had to reinstall as instructions in this video (8:34) left me with hot and cold reversed. Still saved me money but a waste of time.

[@NedzadAlihodzic]

Good job!Good presentation!

[@millerlitedrinker]

Watched your video to replace our shower mixet valve, thanks, your video was very helpful! i just subscribed to your channel, thanks again!!

[@TheShackHome]

millerlitedrinker so glad to help, thank you for subscribing I hope i can inspire and help more in the future.