Thinking of a Cummins Conversion? Watch This First!

If you had the budget, What Engine would you swap into your 4x4?
Today on The Skid Factory, Al talks candidly about the Pros and Cons of a Cummins swap into a Nissan Patrol. There's a lot of variables to consider and it is a costly conversion.
#4x4 #Diesel #Cummins
Support us on Patreon: / theskidfactory
Buy merch here: www.theskidfactory.com
If you like what you see then Share it with your friends and don't forget to subscribe and hit the bell for Weekly episodes!
For updates keep your eye on The Skid Factory (TSF) here:
woodrigos?...
theskidfact...
/ theskidfactory
turboyodats...
/ theturboyoda
Please note: We like to make interesting car mods and show you how we've gone about it, but we can't promise that anything we show you will work for your particular car, or that you won't harm yourself, someone else, your car or your warranty doing it. Please be safe, be responsible and unless you know what you're doing, do not fool around with very serious machinery just because you've seen us make it look so easy.

[@theskidfactory]

New Merchandise Available! theskidfactory.com

[@mickreading4692]

Hi I was wondering how a V8 landcruiser motor would go in a patrol and why no one has tried I was told they don't fit which doesn't make sense when they fit a duramax any comments

[@mitchelllax2840]

@@mickreading4692 667⁶you 766677

[@ekim72]

You couldn't fit a 6 speed allison 2000 in there?

[@vk2aafhamradio]

Active noise cancellation might help knock down some of the engine noise. Pretty much put a mic near the driver's ears, feed that signal into an audio amp which drives a speaker, but swap the polarity of the wires going to the speaker. If that works a bit, you can make it fancier by gutting a pair of active noise cancelling headphones and using the output to the ear cup speakers to drive the audio amp & speaker.

[@theuniverseandlife2904]

We wish researchers and workers in the technology and engineering department to find plans for the new car industry Because new cars should be flying saucers in the sky and These flying saucers must have three perks 1 / The flying saucers must be self-driving so that everyone can use them 2 / The autonomous driving of flying saucers must be based on artificial intelligence programs 3/Artificial intelligence must rely on the new Google Maps in order to direct the launch of flying saucers to the desired places . Send these three basic demands to the technicians and engineers in the mechanics and technology department in order to make flying saucers

[@bjones5240]

I really enjoy the no fuss approach Al takes to these videos. SOO many cowboys on the net talking rubbish. Al has wiped the floor with them in such a modest professional way. Thank for everything you do Al. I hope you continue along and provide more great info in the future!!! nice work on the edit to Woodrigos

[@smitty4321]

Lot of people on the net think the engine itself is the only cost to an engine conversion.

[@siltres05s112064]

Well said mate.

[@The_Absolute_Dog]

Thats my favourite thing about Al, he was so nervous in the early videos, because he's just a guy that knows what he knows, and does what he does, but also knows when he doesnt know something.

[@williamhardes8081]

@@smitty4321 they wish! lol

[@j.barrett9424]

Projects are always bad financial decisions but it's what we like and it makes us happy

[@shawsie5780]

💯

[@michaelperrin3503]

Yeah and it’s still cheaper than a 79 land cruiser price and if done right better in every way and there so popular so it’s probably not as bad as it sounds long term.

[@PheonixRise666]

It all depends on the size of the project. "Small" upgrades around a weekend to bash out can be really economical. Full builds and conversions are rarely economical but they really build the sentimental value.

[@olik136]

I don't know- have you seen what new cars cost these days? You can easily spend 45k€ on a VW Golf... a nice Audi sets you back 65k€...you can mess around with a project car a lot for that... sadly in my country project cars are very hard to get legal- and especially engine swaps are almost only done withing a model range

[@kramer26]

Yep, just take me n my Subaru. I'm 14 years in and it's done more miles on the back of a trailer or in a shipping container than it has under its own power!! Just need to get that EZ30 built, hey Al...? 😉

[@hellodisdat]

'You're probably getting sick of me talking' NOT AT ALL I'm not a mechanic, have never and probably will never pull a car apart and I could listen to Al explain stuff all day. Passionate no nonsense approach makes every thing Al says hold weight. Always learning from you Al, Cheers

[@scottieb8313]

Dam right!!!!! keep on Yacking Al !!!!

[@HereIsMyOffer]

I'd enjoy an occasional podcast with Al & Woody + gang, sharing some of their stories, build successes, failures and cars they've owned. ''The Skidcast''

[@The_Absolute_Dog]

Like, I'll never have the tools or space to do it, but I love hearing about it. I like to dream that maybe one day I could, and if I did, I would be fucking overjoyed I listened to those vids

[@lwhite513]

Al could probably read the phonebook and I'd like and subscribe 😂 Loved this!

[@williamhardes8081]

well said, couldn't agree more.

[@NarfBLAST]

15:30 "Nowadays everyone hates smoke, which has changed from last week." Subtle and timely remark there, well said.

[@nordic5490]

Well... outside or our bubble, most people want clean air and quiet cars

[@muf1772]

If you follow Deboss, he's always said that rolling coal is childish and offers zero performance benefit.

[@DieselRamcharger]

@@nordic5490 even inside your bubble people are anti "coal rolling" cucks. its all about division and infighting. Which there is no shortage of.

[@DieselRamcharger]

@@muf1772 "Performance" is when a machine does what YOU want it to. Deboss's assertion that he knows what is best for you is the over arching problem here. You gotta get better at spotting authoritarian cucks and silencing them instead of elevating them.

[@ArmySigs]

@@DieselRamcharger Making childish comments to defend yourself against being called childish, that's gold

[@joealex65]

When Master Turbo Yoda gives you advice about engine swaps, you just sit down and listen! 😎

[@andersjjensen]

Yup. I'm not ever going to do an engine swap, but I sat down and listened anyway! :P

[@MiGujack3]

@@andersjjensen Not ...yet.

[@hahaha12345678993]

moral of the story everything is expensive hence why we're all on here watching people do conversions

[@davey_projects2977]

Living vicariously through others is my favourite hobbie.

[@worldhello1234]

No, joker, not expensive is subjective and relative. :)

[@Aspire198]

This is a really good 'build summary' presentation. I'd like to see something like this with any build.

[@sinva4847]

That would actually be a really Good idea

[@Yvolve]

Definitely a good idea! Puts the build into perspective. Hard to judge how much money goes into a build like this, or the actual time and effort. I can understand some owners don't really want Al spilling the beans on how much they've spent, but would be nice if possible.

[@MightandMagic88]

Speed Academy does this once in a while but it would be nice if it was more common among the 'project car build channels' in general.

[@dallasvanwyk]

Absolutely love the project follow-up. I will almost definitely never even own a patrol let alone do an engine conversion on one, but I still find this background knowledge and perspective fascinating.

[@IBOO57]

Nice to see honest opinions from someone about there own build. Its too easy to just pretend what you did is all spot on and perfect. 4JJ1 would be a good choice in the Diesel world but i reckon a Barra with around 380 RWKW would be tough to beat and the 25 odd grand of fuel you could buy with the savings would go a long way.

[@camandjaiden]

Agree, the 4J would be a great choice with the aftermarket possibilities!

[@GarageTakai]

Too true on the 4JJ1. Considering one for a 60 series conversion… or a Barra.

[@keithy363]

Yes barra would have high hp and the power would be in a different band high in the Rev range being petrol this makes it easily down low with minimal stress , but it’s all about what noise our ears like to hear 😂😂

[@keithy363]

@@jmac822 maybe so but would be highly stressed maybe ?? Where as these big ol donks just plod along mainly in idle , also the 4.5 cummins get good power very low in the Rev range which is where u want it ,

[@bradmcgrath358]

I daily drive a 4JJ1 Rodeo, and have had a TD42T patrol for the better part of 12 years. I wouldn't put a 4JJ1 in a Patrol, While the peak power might give some people a boner, the driveability is not the same.

[@DomsE36Garage]

ROFL at the ending. I do a lot of Umm's as well and am always getting yelled at haha. Great build, solid rig!

[@wilbertbirdner1303]

sounds like my wedding speech

[@aaronturkey]

Honestly informal episodes with Al just talking about stuff are some of the best episodes.

[@NathansMoparGarage]

I enjoyed watching the whole build from the Deboss engine build all the way the finished product.

[@coltonmcrae5873]

I LOVE that Al embraces modern tech. Too many guys afraid to learn. They see all the wires and run for the hills.

[@matthew7448]

true and i took the time to learn it and then i only ran from it more. what happens when a pcb board gets fried or the software acts up. with mechanical pump theres no guessing u can see and feel everything that’s happening. switching away from carbs in favor of fuel injection is one thing, but those mechanical injection pumps are stout mechanisms. they tend to be far more efficient as well suprisingly.

[@archierobertson5426]

It very much depends on the car. I know in the classic minis the electric fuel pumps are the reliable option because the mechanical fuel pumps can fail in a way that leaks fuel into the oil

[@nicanatorxx2]

One of the BMW M57 varients, hard to beat price wise. Tremendous tunability and incredibly strong. Can get them from UK wreckers for pennies. That or an OM606.

[@Jez3134]

I saw a couple GUs with an M57 conversion from Russia and Europe, they were making huge power from what only looked like a backyard job

[@hannahranga]

I've been ogling an m57 for my d2. Would be a hell of a step up from the current td5.

[@75L48]

Exactly. I cant see any good from swapping 6BT in passenger car like Patrol. That thing must weight in like two almuninium M57s.

[@89da121]

Love your work and the amount of effort you guys put in to bring us these videos! Thanks

[@matttunne2709]

Great vid! Thanks for sharing all of your experiences with us Al.

[@chadlegault9993]

Thanks, Al, for sharing. I think there are a ton of us that want to learn the details like this. Sooooo appreciate this.

[@usedchoc]

So Ummm… I see woody being denied a lemon squash in the near future. Well worth it though. Great insight, thanks Al and Woody.

[@sirstevo]

Took a while for this to pop up in my feed. Glad it did. Great video

[@bluedogdataelectrical6303]

Hey mate. What a cracking video!! Once again your knowledge is outstanding and your willing to share with us all.. thanks man great work

[@inspectorgadgetman]

Awesome advice Al. Lots of things to think about when doing these conversions. Also plenty of time and money!

[@hilto4534]

These are some of best videos with real world costs from experts ie experienced people. Reminds me of my Series 3 Land Rover and the Holden 186 conversion. It was an Aussie thing to do. Thanks Al & Woody

[@williamhardes8081]

love the ep. very calm and straight forward and most of all informative. i'm more of a GO FASTER person than a bush basher but i still really enjoy all the builds regardless of what they are. every build i learn things and that's is one the the greatest reasons i keep coming back. when i finally get my project underway, i hope i remember one particular piece of advice from al's words of wisdom. use ya brain! i love the sound of a GM 8V92. would that fit in the next one? lol.

[@roryalgate872]

Love your videos mate...nice and relaxed and easy too watch.

[@JohnRolyAU]

GVM and GCM became a problem when the insurance companies started weighing everything that fell out of your 4x4 onto the road after you rolled it with your 87ft van on the back to deny a claim.

[@rlaxton666]

And quite rightly so! The vehicle was engineered for a given mass for a wide array of reasons. Brakes, suspension, chassis and so on could all be inadequate. Poor control of your towed loads can also be a real problem, leading, as you say, to your 87' van spilling its guts. As much as I am not a fond a large US pickup trucks, if people are going to tow 3500kg and heavier caravans around, they are likely a far better option.

[@wobblysauce]

Yep and the new ute/truck things are the only way to do it and still be under that number, without being the only person in the vehicle with no gear.

[@rp3874]

Hence I bought a new silverado 2500HD to not risk a no payout if something happened when towing the $250k toy

[@JohnRolyAU]

I've done a GVM and GCM upgrade on my 200 Series. I only tow a Kimberly Kamper and it still get's sketchy sometimes.

[@scottdaniels251]

Agreed ... If your going to tow small houses behind a vehicle, get the right damn vehicle. F truck, ram etc and be safer while doing it.

[@andreandrews571]

Great editing skills Woody

[@PJWXR6T]

A very good session, thanks. I appreciate hearing it all straight without the hype.

[@davidhiscock1969]

Nice and honest, no bullshit video . Do enjoy watching and listening to how Al does things. Keep up the great content guys . Greetings from the UK

[@LitchKB]

Absolutely love listening to this sort of insight, and the concise knowledge transfer format. Not sure how that works since I never intend to lay hands on a cummins, ever. Just feels like food for the brain.

[@JimOHalloran]

Smart people, talking intelligently about their field of expertise is always good for the mind.

[@vincem5]

Google M57 bmw patrol. they seem to go great. thanks for sharing your thoughts on this conversion, especially since you have done a couple of different ones. i have had the a duramax also and now a LSA . they are both great in their own right but very happy with the LSA now and prefer it. the ease to work on it, to get parts locally and the milage is no worse than a 4.5 or 4.8 from Nissan and instant power it makes, makes it a very enjoyable 4 wheeler.

[@wayneholzer4694]

Great video glad you are honest and pointed out the pros and cons and especisally the costs involved I didn't think it was that expensive but the amount of work let alone parts I can see how quickly the costs add up anyhow thanks for the great content over the years and as always of high quality and look forward to each new episode cheers

[@johncarey9149]

As usual Al, it's a pleasure to hear your no nonsense, zero BS thoughts on the subject.

[@nuttykrust]

The BMW M57 3litre diesel with the 6 speed auto from an X5 would be a nice conversion

[@nicholashartman4200]

Umm uh.... best ending so far, you're killing it Woody!!!!

[@NKPGarage]

Very informative video on the swap. Thanks for taking the time to put this together

[@stepheneastmam2469]

That out take was the best 56 seconds of my year 👌. Good work as usual boys.

[@ralfszemzars1885]

Dieselmeken and BlackSmokeRacing would be a great place to start when looking at Mercedes diesels :) I love this type of video where the job is being weighted and everything told as is. Keep going guys!

[@thomaswalsh471]

Diesel pump UK have alot of experience with the om606 conversions. They can supply a full billet aluminium conversion kit for the patrol.

[@IBOO57]

Thanks i hadnt seen those channels but have now subbed. looks good.

[@adamedwards2287]

I'd be keen to see an om606 turbo conversion but only being a 3lt might now be the greatest for a patrol.

[@tcjay119]

That'd be pretty cool, im sure a 600hp om606 would get a patrol moving fairly easily 🤷🏽‍♂️😂

[@chucksanders7131]

Al, Thank you for taking your time man. This is something that most people don't want to watch, but should. Thanks again for taking your time out of your day to explain to us normal people to make us less normal :)

[@elrud5964]

Love hearing your perspective on anything mechanical

[@inspectorgadgetman]

Woody- you could set Al's umm's at the end of the video to a techno rhythm and sell a skid factory original composition 🤣

[@mrclown7469]

Come on Alan, go full madlad and install an exhaust brake 😁 If the Karens thought it was loud before...

[@boycottjews]

Karen is antiWhite slur. Stop copying rappers and other antiWhites.

[@shallowabyss515]

@@boycottjews Can't tell if you're joking or a nutter.

[@boycottjews]

@@shallowabyss515 I rarely assume someone's names is shaniqua

[@shallowabyss515]

@@boycottjews Nutter. Got it.

[@boycottjews]

@@shallowabyss515 you must be a semphard.

[@boyardengels]

great videos, really enjoy your guidance and knowledge sharing!

[@aleksydabrowa1114]

Having done this conversion myself, but slightly different, I’d like to add my 2 cents. Obviously I didn’t do it quite the same as you but it’s definitely similar. I used a 12v 6bt through Texstar automotive. Originally all we were going to do was change all the gaskets, but thought since it was pulled down why not rebuild. Engine cost was $7200AU landed in Brisbane, rebuild was nearly 3k, but only reply once major parts that needed, and replacing all valves and stems. I always wanted a manual, and went with that to begin with, before going through 3 patrol gearboxes and shearing 3rd in all of them. I eventually went to a basic 4l80e, which was functional, but wasn’t what I wanted. Never played with the fuel pump too much, just went 4K gov springs and a fuel plate, but it just wasn’t to my liking drivability wise. Don’t get me wrong, could pull a house down but I’ve just never been an auto man. So I started looking down the path of manual. Ended up with a PaR gearset with custom 1-5 gears ( they have a shoo wheel of short or tall for every gear depending on your needs. They were originally designed for the Dubai 4.8’s with stupid power) and they have actually worked an actual treat! Thai set up also comes with a billet input and output shaft that is considerably bigger than factory to handle the extra load. Considering it only costs about 12k all fitted (including custom HD clutch to suit the shaft, it has honestly made the entire investment worthwhile! Taking out all the costs of doing things wrong, it can easily be done 45k on road with Abrams new motor and gearbox. I tow an OP4 camper as well and dragged that up little red just to be sure it could take me anywhere, and has no let me down. I have since done 8500k around Oz and wouldn’t change my set up for the world. Even with all my weight, fuel consumption is currently sitting at 13.5lph which is ridiculous for a car that size and weight! I personally believe that if I knew what I did now at the start I would’ve saved myself atleast 20k, but would recommend this conversion to literally anyone that will listen to me!

[@theskidfactory]

Thanks for the feedback mate, much appreciated.

[@daleboulton1169]

I might need some of that info……just bought my patrol and I’d like to have a plan in place if it decides to go bang!

[@catatropic233]

I’ll probably cop it here, I’ve had many cruisers and patrols. I’d love to have a S4+ patrol with a 5speed 1hdfte.

[@Oz4me_craig]

Davo, have to agree, the 5speed auto and 1hd-fte conversion in my 105 is smooth, quiet and gets it done .. I'm also Gu fan for the suspension geometry and diffs of course .. but like most of us, just want more than what came under the hood! For a second project, I'm on the lookout for a cheap S4 Patrol and I'll do the same again .. You get 24Valve, efficiency, high enough torque to tow whatever, no overheating and long term reliability. Front cut FTE for $12k and if it's done less than 500000k just send it, with a bigger set of injectors and turbo .. No rollin coal!

[@theskidfactory]

It's certainly not a bad idea but also not cheap, that'd be a $30k easy.

[@Oz4me_craig]

@@theskidfactory Spot on with the calculation, 30k for the conversion is realistic, plus the donor GU .. makes an end product that is better than either of the brands ever made and less than half price of a new version of either .. IMHO

[@catatropic233]

If you do happen to do this fella’s, the new yanmar Marine engines are a 1hdfte. Instead of paying 18k for one with 500k, 21k for a brand new engine is the way I’d go. As soon as someone makes a 1hd to re4/5 adaptor, I’ll be doing this. Re5 behind the 1hdfte would be my dream car, keep up the wealth of knowledge and future episodes fellas never miss a skid factory vid 👍

[@darrenlangford6664]

Thanks skid factory you helped me with a few unanswered questions. And probably be able to figure out a job I'm doing. Cheers All

[@paulweir3225]

Mate, your experience is most helpful, The info, informal or not is terrific.

[@siltres05s112064]

As someone that spent a fair bit of time doing similar things for a living up until the $$$ of mining were too hard to resist, TSF is one of the rare channels I can relate to that dont have me anxiously pulling my hair out every 5 minutes. Appreciate the honest review from a very knowledgeable fella, with a no-nonsense approach to these more complicated builds.

[@MrCrowart]

I think i will stick with my factory TD42ti, but if i was to do a conversion on a ZD grenade i would definitely go a OM606

[@RobsDIY]

wish they were avaiable in aus, or at least not as rare or hard to get part from outside uk or germany

[@andrewshackleton3700]

There not hard to get just get one through uk eBay or most engine recycle business. Just no there not rare …

[@lachlanparkinson7808]

Absolutely love the content (as always) Wednesdays are definitely a highlight!

[@carbs6629]

I can say with 100% certainty I will never be doing this conversion, but I love the sharing of knowledge! Could listen for days.

[@_Lewie]

Glad to hear someones conversion cost more than mine! I have just completed an LS3 and 6L80 into my GU and it's now a sweet, smooth ride.

[@Dan-rg7jj]

Ls3 factory cams suck and so do the heads for low end. Stick a btr torque cam (202 duration 111LSA) and ls1 style heads and manifold. Will have better torque around 2k rpm maybe as much as 40lbft. The Australian LS1 cam is even worse for low end. Best factory low end cams are L33 and Lq4. But the btr 202 cam is better then both. People forget that diesels don't rev past 5k. But everyone poops on these tiny LS cams even though the are good to over 5k rpm and most ppl go for something in the 22x and up duration. Unfortunately.

[@some1else155]

How much did you spend?

[@tcmx712]

@@Dan-rg7jj nobody puts an LS into their patrol to putt around at 2000rpm though haha

[@Dan-rg7jj]

@@tcmx712 Have you ever driven something with a 4 speed that weights 3t plus? Even 2t plus unless you have bulk torque at 1200rpm like Al's it's gonna be doggy. Even with the correct gearing. Really, you are governed by gearing and in hilly burbs mine sits between 1k and 2.5k rpm stop start and up to speed. About 2.2k on the freeway in 4th probably similar to Al's. No idea what gearing to tyre ratio his is? Never said an LS won't do 5k plus. I have a 383 so torque is bit too big for 50kmph side streets at those kind of rpms. Also you can't just nip through the gears with 4 speeds not enough spread so you're always well over the speed limit. Sure mine is better now with the mods but still need more down low.

[@tcmx712]

@@Dan-rg7jj dude op has a 6 speed and ls3 so why you waffling on about 4 speeds hahaha, and you do realise a standard ls3 has more torque at 2000rpm than a v8 70 series does anywhere in the rev range let alone anything that comes standard in a patrol so I don't know why you're saying it needs more torque down low when it moves the patrol a hell of alot better than stock???

[@shapoopeedee]

ive seen lots of bmw m57 swaps into patrols. hell of an engine to put into one

[@JAM4382]

I was looking to comment this. The m57 is a badass engine! There are a few in USA making close to 800whp and 1,100ft lbs (600kw 1500nm)

[@shapoopeedee]

@@JAM4382 stock engines with a light tune make 350hp 550tq and rev to 5k rpm. Love mine in my 335d.

[@JAM4382]

@@shapoopeedee nice👍🏻 I had a 335d also until some asshole wasn’t paying attention and totaled it. I so miss driving it, I want to get another someday.

[@spannerworx7106]

@@JAM4382 utter bullshit.

[@JAM4382]

@@spannerworx7106 Santjer Performance BMW M57 Triple Turbo 793whp / 1082 lb ft…. The information is out there. It’s not a kit you can buy yet as they are still developing the setup.

[@boomsjapan]

Thanks for the honest review awesome work as usual mate 👍

[@Mafk101]

I'm currently doing a TB45 to TD42 conversion and keeping the RE4 auto like you did with the red Patrol. Your videos have been an absolute wealth of knowledge and I really appreciate how much detail you go into. I am making it hard for myself by not manualising the auto like you did, but also keeping the ECU and TCM and not going the easy but expensive route of getting a kit from Wholesale Auto or wherever. Love your work guys, keep it up!

[@nrs91]

You will probably have 300ft/lb of torque at 1000rpm without the turbo spooling which is why they move on ok but a cummins with snappy response is much more fun and usable and worth sacrificing a few peak HP for. On my Cummins Landy the fuel economy was the same as the 2.5TDi it replaced but it didnt drop off when I was towing which was nice!

[@ianirvin3511]

Thanks for your extensive knowledge mate. I learn something every time.

[@sittos191]

This has probably been my favourite series you have done on this channel. Love your content, would love to see a good ol OM606 in a car 😉

[@oldfalcon3245]

Had a good chat to my tuner about y61 engine choices. He’s dead against Barra conversions because they end being done too cheap. Ideally I would just go y62 with a Harrop and leave the y61, but for half the price a Cummins swap is very cool

[@michaelatkin2562]

1HD-FTE conversion just to piss everyone off 😀

[@jinglemyberries866]

hahah that would be so good

[@matthewdodson2320]

Been done here in nz by krae

[@jarrod1687]

There's a few getting around Aus as well

[@craigmaloney1573]

Who would thumbs down this video? Seriously. Al, great TED talk. Super informative. Thanks a lot guys. Look forward to the next one.

[@NathanNostaw]

Thanks for such an interesting de-brief on the conversion. I don’t have a patrol, but really enjoyed this just for the info. I’d like to see this format after each engine swap build. Cheers

[@andrew81au]

Not sure if it's still being done but toyota's 1hd-fte would go ok in a patrol

[@murrayobrien6672]

It’s been done ✅, and is excellent

[@magnusbuinevits9535]

If the Mercedes diesels seem interesting to you, be sure to also check out the BMW diesels. The M67 is interesting, but not that common, while M57/N57/B57 are very well supported, though they obviously sacrifice some displacement.

[@davydoo81]

I prefer reliability, something BMW badly lack.

[@magnusbuinevits9535]

@@davydoo81 to each their own. I like to judge engines and cars for that matter by their merits, not by their badge. Saying that those engines are unreliable is simply misinformed.

[@davydoo81]

@@magnusbuinevits9535 lol, you misspelled “informed”,

[@magnusbuinevits9535]

@@davydoo81 do please share with us what the issues with those engines are

[@kristoffer3000]

@@davydoo81 Some of the most reliable engines ever made, but okay.

[@macca89doz]

Was looking into this a few years back. Went with a 1HDT conversion for my 105 series instead due to availability, ease and cost. Was pretty happy with the result, made 190hp 700nm on 35s and never gets hot.

[@donaldwills2135]

This is now my favourite video on here. Normally blank out the talking but this was perfectly done. Well done

[@dangdang3970]

Just when i thought i could take on putting a thong slapper from a 79 in my 80, along come al n woody and hit me with a reality check 🤣 Great stuff guys and awsome info keep it up 🤘👍👌

[@craigdavies8099]

I think a built, 80 series engine is enough! Easier and much cheaper! Nearly finished rebuilding the 1HD-t in my 80, that's been expensive enough. Went nuts though! 130% injectors built pump big turbo. Already have the rest of the necessaties fitted to make it hum. Instead of rebuilding my block I was able to get a Genuine Toyota short block brand new in the packaging.

[@toranaandy2245]

The money you save in the wreck cost will be eaten with the conversion. Bite the bullet and buy a HDJ100 wreck and get stuck in.

[@jacobpedersen8514]

Id love to see a small CAT 6cyl or v8 in a patrol. I've seen a 3208 CAT V8 in a 40 something series cruiser so should fit in theory

[@i-am-that-what-i-am]

Trouble is, CAT's are way too heavy, even the later modular engines

[@lamarzimmermanmennonitefar5269]

Dt360 any day

[@jacobmoses3712]

I have seen a 3208 in a Ford F250 on youtube. The guy had to do a body lift to make room for the engine. He also had to upgrade the front suspension (more leaves). 3208s are pretty big

[@reggien737]

Hey Al! Recently picked up a 12v p7100 5.9L here in the states with headstuds and all for $1500, somewhat recent full rebuild. Going into a barn find 97 dualley that died to the dial pin in 2005. Here in the states. West Virginia beef farmers. Love watching you and really enjoyed the turbo fail video since I experience alot of my own mistakes.

[@Cozmicksilver]

Child hood memories of my friend broadsiding me in a mud pit. Four wheels spinning and the sound of a duel exhausts 350 chevy roaring, just a magic moment. My little LC torana was buried.

[@dandilts3213]

Not even remotely close to getting sick of hearing you talk about what you know. When someone knows what they are taking about & is willing to share their experience based knowledge, it’s nothing but interesting & enjoyable to listen to. Keep on doing what you’ve been doing. I for one appreciate learning from you. Thanks!!

[@pauldowie1399]

This was really great. As an ordinary viewer we rarely really understand the impact of these type of changes let alone the cost. Great vid Al. Thanks.

[@MicahBell_1860]

Thank you for a well balanced arguement of the pros & cons. I have been weighing up between a 6BT, Duramax & rebuilding& stroking the original 1HD-T in my 80 Series. I think l am now leaning even more towards rebuilding & stroking the 1HD-T

[@vindicator2]

Great vlog as all are from you guys! If you have another Patrol available consider doing a OM606 or the later model OM648 (common rail). But if the goal is to go bush on remote areas I would choose the OM606 any day. Stay Safe !

[@scottdaniels251]

Super informational 🙂. Thanks what a great little listen .

[@jonasfreitag1344]

Thanks so much for sharing. That was super interesting!

[@svenvanwesterloo173]

What a lovely change to hear someone talk about this without all the youtube/views/likeable/bs and just telling it as it is.

[@Not_Built-Right]

The whole build is bloody awesomeness and has helped me along witb some great solid advice good shit Turbo Yoda & Woody .

[@elishagumowski4637]

I'm a young fella who's been tinkering on an old patrol myself. I'm certainly not knowledgeable nor full of money but still enjoy watching your videos. Appreciate AL's straight up approach to money pits like these and look forward to seeing where they go in the future. Cheers boys

[@scottbeattie6645]

Thanks for the general knowledge. It is surprising how much you do learn from content like this even if a full blown conversion is on the cards. Research Research Research Plan Plan Plan and repeat. Thanks Al for being honest and realisation. Enjoy sunny QLD

[@fossilfuelenthusiast]

Uuummmmmm, Nice video boyz. could listen to AL all day.

[@chadlegault9993]

This is by far my favourite channel. :)

[@phillmorgs5930]

Well done boys great work well rounded build series really cool.

[@mitchellharding8778]

this really was a grest episode. thanks for posting, hope theres more like it.

[@steveczislowski3896]

Great Video!! Appreciate the honesty 👍

[@alindorindicu3732]

A lot of BMW M57 are swapped in Europe, although not done legally as in Australia. Some shops in Iceland do OM648 as it must be easier to find and more modern than the OM606. Thanks again, very interesting. I've been watching your channel since the double unicorn swap and it's still one of my favorite, even after 3-4 years. Keep it coming !!!

[@paulwalker427]

Bloody great video - love the format

[@MrJapatron]

Great informative clip, cheers guys

[@Tuilaione]

One of my favourite shows i look forward to. Thank you TurboYoda. 🙏🏽🙏🏽🙏🏽💪🏾💪🏾💪🏾

[@brodienunn8638]

I own a 105 and not a patrol but really enjoyed listening to what you had to say

[@kevinhurley6782]

I'd have listened to you for another 20 minutes! Great video!

[@bigfatfreddie3781]

EVERY build you do needs a run down like this. Good stuff.

[@miniwhatt]

Awesome vid mate. Vey informative. As a 24v cummins Dodge Ram owner here in Aus I can attest to a lot off the engine specific things you mentioned. I just rebuilt the 47RE in mine. So much damn torque

[@GarageTakai]

Great wrap up. Always good to learn more on how others go about it. On the engine side, currently considering a 4JJ1 or a Barra for a mates 60

[@MadmanJnr]

What a great discussion. Honesty the lot. That ending lol. On the conversion idea. I think it would be pretty funny to put a barra in a shorty

[@noclafdrof]

Well that 20 minutes felt like 2. Exactly what we all needed/wanted to hear. I reckon it would be good to go over the young lads Cummins patrol and do a compare of gear he used, costs & issues he ran into Keep up the good work lads 👍

[@peterwooldridge7285]

What a great and honest review...thanks

[@slvr1.618]

Turbo Yoda is an encyclopedia of engines and swops, the honest and objective opinions based on actual "been there & done that" knowledge is quite something,the smaller capacity diesel engine swops like the Mercedes OM sounds interesting and seen online they make good power as well so Turbo Yoda & Woody please on the next swop maybe consider this,either way - really enjoy the channel and the passed on education!

[@MrZilla500]

I put a p pump 5.9 into my 79 ford, kept the dodge running gear but built it up. Can confirm the noise. Couple tricks are oil pan wraps, pushrod cover and valve cover wraps, where most the noise resonates. Made a good difference in mine.