This is why your SCREWS are STRIPPING in Steel Studs!!!

  Рет қаралды 62,076

Vancouver Carpenter

Vancouver Carpenter

Күн бұрын

Пікірлер: 81
@brow1901
@brow1901 2 жыл бұрын
Ben I used to work for a US board manufacturer, you're correct the edges are harder but it's not from compressing the bevel. There are 2 types of slurry that fill a board during manufacture: the core essentially has soap which traps a little air to make board lighter, the second slurry is a layer without bubbles and designed to be harder which is spread thinly on the face paper and heavily near the edges. The face paper is unrolled sprayed with the face slurry then the core slurry is poured over before the back paper is laid on. This is done intentionally to reduce handling damage during delivery.
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
Great info. Thanks Joe!
@manuelmarinez9858
@manuelmarinez9858 2 жыл бұрын
That all makes sense.
@marjieyoung9570
@marjieyoung9570 2 жыл бұрын
That's so cool. Thanks for telling us. It's really interesting.
@gregmaffei4820
@gregmaffei4820 Жыл бұрын
Straight from the source
@spf-92.5
@spf-92.5 4 ай бұрын
Does the board go through some kind of press to give the beveled edge/ recess the contour it has? All the new light weight board have a much better recess for screwing but tend to cut a lot worse then the old heavy board.
@davidgagniere2923
@davidgagniere2923 2 жыл бұрын
Your videos have never wasted my time. Sometimes I watch them a few times (a month or so apart) just to try to absorb all the details. As an amateur I usually start somewhere near the middle (on walls) just to get two or three in place so I can let go of the board. I've always done the edges last.
@Kensdisguise
@Kensdisguise 2 жыл бұрын
As a life long pro commercial carpenter, I have experienced this 1000's of times. It does NOT happen to all sheetrock, but usually to the rock that has sat on the job for days and started to dry-out in the heat. We try not to add screws in the factory edges until the "adjacent" sheet is being hung (ceiling or wall). That allows for "blowout bumps" when screwing seams. Anyway, you can also take your hammer and just dent the board at the point you want to add a screw. It allows the screw to set perfectly. Nice to see you using a HILTI gun. Best sheetrock auto-feed guns ever made. Keep the videos coming...! GREAT JOB
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
Thanks! I do the same thing about hanging the adjacent sheet first. That was one of the first thing I learned on the job from an old taper back when I first started my carpentry apprenticeship. We were doing reno's in highrises and the taper was helping us hang the board. He taught me to use the router too.
@Kensdisguise
@Kensdisguise 2 жыл бұрын
@@vancouvercarpenter I just realized that I hadn't sub'ed to your channel. Doh! Oversight rectified. BTW, my wife loves listening to your videos as well...I am not sure how to feel about that...LOL
@johnboon5330
@johnboon5330 18 күн бұрын
Wait, you mean, smash the drywall with a hammer? Seriously???
@Kensdisguise
@Kensdisguise 17 күн бұрын
LOL ​@@johnboon5330No. I didn't say smash, I said dent. I know it sounds crazy, but it works. Just use the edge of the hammer head at a small angle to create a dent in the sheetrock. It softens the paper and the drywall, and allows the screw.to properly "set" and not strip when the nose cone hits.
@jeffc4825
@jeffc4825 2 жыл бұрын
Thank you for clarifying that. We were struggling with RC and finally stopped putting screws in the bevel, not knowing why the edge was a problem. Feel great, now knowing the problem.
@Matt-my7pz
@Matt-my7pz 2 жыл бұрын
Ben you could do a video on drill speeds. I started out working nights and weekend with my dad as a kid. He worked at a fastener wholesale, but always was drywall taping painting tiling fence building etc after hours. We originally had a corded Makita, then bought a corded Milwaukee which spun so fast you almost couldn't push hard enough to keep up with the screw going in and lots improper screws ensued. Returned that and got the corded bigger wattage DeWalt and never looked back. We aquired the lower wattage DeWalt screwgun which is terrible! Its the opposite effect of the bigger wattage "perfect speed" DeWalt. That said for all my jobs now I have the compact 18 volt Makita I bought for 1/2 price from the HD rental shop. Also on drywall hole cutters, corded drywall saws (Makita one is money) I should check that you already haven't done these.
@soundman6645
@soundman6645 Жыл бұрын
As I mention elsewhere, here in AU, we use stud adhesive pretty much all of the time. SO, we don't need to screw at the edge of the board. Stud adhesive is actually stronger than screws, because it bonds a 2 or 3 inch round circle on the back of the board. Having demo'd some plaster board, I can tell you this is true. If you put blobs of adhesive along the edge of the board, you only need to put screws some way back from the edge. Assuming the frame is something like straight. We pretty much only use one type of screw here that would be fine threaded .... we call them "bugle heads". They seem to hold well enough in both metal and timber.
@zackerydupuis6724
@zackerydupuis6724 2 жыл бұрын
Amazing video so helpful while also being entertaining and also helps when you need it. Keep up the amazing work Ben.
@goodtobehandy
@goodtobehandy 2 жыл бұрын
Think outside of the bevel. So can you add screws in the bevel after it's screwed down ?
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
You can try but if they start stripping again it's easier to just not screw in the bevel at all.
@goodtobehandy
@goodtobehandy 2 жыл бұрын
@@vancouvercarpenter what about about using adhesive along the bevel if you can't get screws to hold. Or I'm over worried that tape might fail.
@joshuakakar
@joshuakakar 2 жыл бұрын
Another thing that helps is never use anything lighter than 20 ga studs. The big box home centers typically carry 25 ga...which is really only good as a straight edge... 😂. In commercial applications, we're standing our drywall, so we have no choice but to use the compressed tapered edge. I've learned to just avoid 25ga if at all possible. I can't say I've ever had an issue with stripping on 20ga.
@dans4900
@dans4900 Жыл бұрын
Exactly. I special order the 20 Guage. I had a few 25 mixed in. Boy the guy screwing was pissed. I laughed cause I knew there only a couple junk studs.
@GregoryGuay
@GregoryGuay 8 ай бұрын
I have 25ga on isomax resilient channel clips for my walls and ceiling but I’m thinking I should use 20ga for my ceiling. DIY a home music studio / theater. (22’x12’).
@joshuakakar
@joshuakakar 3 ай бұрын
@@GregoryGuay Sorry for the late reply, but yes, you'd probably lessen the chance of sag as well. Hope it turned out well for you!
@tommarsala3155
@tommarsala3155 Жыл бұрын
I'm getting ready to build a pony wall for a friend who owns a restaurant, I'll be using steel studs and then putting USG Fiberock backer board on the framing, which corner bead do you recommend for this type of installation. And what type of mud should I use to inbed the corner bead.
@harrydoherty8299
@harrydoherty8299 Жыл бұрын
when mounting coat racks, cabinets etc i use grk screw. they go thru the wood and self tap into the metal studs. very rugged construction screws with #25 torx heads.
@debandmike3380
@debandmike3380 2 жыл бұрын
predrill. There have been many times where I've had to install a screw next to a blown out edge where I couldn't risk it crumbling apart and pre-drilling kept things intact. So you can either spend a couple extra seconds pre-drilling or several minutes getting mad that things aren't connecting
@DanielHBuchmann
@DanielHBuchmann Жыл бұрын
I notice you have an angled ceiling behind you. I have a basement window that’s frame is higher than the ceiling and that angle may work for me. Do you have any tutorials on framing that angled ceiling?
@Monath3
@Monath3 2 жыл бұрын
Yep I go right where the bevel starts. Also in my experience for whatever reason its the cordless drills that will strip screws more frequently. Corded ones don't seem to do it as often. I try to use my corded Hilti for standups and save the cordless for structural studs or topout where a stripped screw here and there doesn't matter so much.
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
It must be the cordless ones losing torque as the load increases.
@ArmedTherapy017
@ArmedTherapy017 9 ай бұрын
How would you attach a wooden cleat thats half inch thick to an office drywall when you dont know what kind of studs…a long thin thread drywall screw and hopefully catch a stud or some type of anchor?! Ty anyone for your input.
@DersonoJambu
@DersonoJambu 11 ай бұрын
What do you mean by outside bevel? Is it right? It's bevel right? Do you mean a seat hole?
@Newokie59
@Newokie59 2 жыл бұрын
I had no intention of learning something today......Dammit Ben
@ConnorGPreston
@ConnorGPreston 2 жыл бұрын
Perfect timing... have a Steel Stud job tomorrow.
@mikerowe4515
@mikerowe4515 6 ай бұрын
I would like to see an video on how you put up that pull bar behind you.
@vojnikjna30
@vojnikjna30 2 жыл бұрын
Yes you got it. Also if you go slow with the rpm’s or use wood screws help sometimes. Not all sheets are the same and some studs are plain old junk.
@bkay24
@bkay24 2 жыл бұрын
great videos. very helpful. A quick question... do you have any tips for attaching baseboards to metal studs? In process of trimming out a new basement, and a few tests with a 16 ga nail weren't successful in grabbing the metal stud securely. Thanks in advance.
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
Just use adhesive when installing. Something like PL premium works great.
@patrick8367
@patrick8367 2 жыл бұрын
May I ask what kind of screws I should use for screwing things into steel stud? I want to hang shelves, etc. And what's the best way to find the stud? Thank you
@joshuakakar
@joshuakakar Жыл бұрын
Depends on what you're fastening to the studs. Metal studs don't hold as much as wood. Typically a fine thread sharp point screw for lighter gauge metal. I've found that Spax brand screws have great holding power in metal studs for attaching shelving standards. As far as finding studs, use a strong magnet to find the drywall screws beneath the paint, set a vertical laser line at that point, and there you go. Hopefully the stud is plumb...😳!
@gregmaffei4820
@gregmaffei4820 Жыл бұрын
I love your taper impressions
@deankay4434
@deankay4434 Жыл бұрын
Can't you change the clutch setting? I said before, I don't drywall for a living, but cordless drills and a magnetic bit with a drywall screw sleeve are sold. Then set the clutch lower so tight gets tight and edges don't get stripped. I don't know.
@mbschu
@mbschu Жыл бұрын
I’m hanging my ceiling with 5/8” in RC1Pro channel and was stripping almost everything using my cordless drywall gun… I tried my cordless impact with a dimpler and for some reason that worked. Bummer my drywall gun isn’t working but at least I have an alternative.
@GregoryGuay
@GregoryGuay 8 ай бұрын
What size screw worked for you? Typical #6 fine thread? I’m using metal hat channel on special acoustic resilient clips and my number six fine thread self tapping screws were stripping pretty easily until I changed. However I’d still like to try something a little bigger like number six or number eight to reinforce.
@kevingraham9697
@kevingraham9697 2 жыл бұрын
Thanks for reading our comments and making a follow-up video you the man
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
My pleasure!
@debandmike3380
@debandmike3380 Жыл бұрын
yes but when you are hanging vertical sheets on metal studs which is common every single joint on a stud is going to be at the edge of the bevel. even worse. So this video really doesn't address a problem
@ICopiedJohnOswald
@ICopiedJohnOswald 2 ай бұрын
What drill is he using?
@Relaxokay359
@Relaxokay359 Жыл бұрын
I put steel studs on my ceiling and use 1/2" dry wall. And not a single screw is fighting on it and it's driving me crazy. I'm just going to get won't 2/6s next time to sister to the ceiling joist.
@tyroneclarke1666
@tyroneclarke1666 2 жыл бұрын
Hi Ben. Always enjoy your videos. The screws you’re using to screw into the metal frame appear to be wood screws. One would think metal screws which aren’t as coarse wouldn’t strip out so easily. Cheers 🇦🇺
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
Those are fine thread drywall screws intended for light gauge steel stud.
@tyroneclarke1666
@tyroneclarke1666 2 жыл бұрын
@@vancouvercarpenter Ah! Thank you Ben. Cheers mate.
@scottspeig
@scottspeig 2 жыл бұрын
@@vancouvercarpenter Really? Fine thread into light guage steel stud? I always order coarse thread by any metal below 3mm but I'm not a drywaller (I'm a Facade Designer - cladding, curtain wall, glazing, etc)
@scottspeig
@scottspeig 2 жыл бұрын
Our problem is that contractors use their impact drivers with the TEK screws we supply, and Impact drivers are notorious for ripping the heads off the screws!
@Ghetto_chef
@Ghetto_chef 2 жыл бұрын
I been a union carpenter for a long time dont use self tapers on light gauge it will strip most of the time use wood screws pointers on light gauge metal and they will never strip…. Southwest carpenters local909 and I’m a drywall contractor all we use is pointers on light gauge
@MikePritchard-e7t
@MikePritchard-e7t 5 ай бұрын
New to all this. This is gold.
@RickJones222
@RickJones222 2 жыл бұрын
Love this guy!
@michaelplays2449
@michaelplays2449 2 жыл бұрын
Good video, thanks 😊
@rockinrobbie1985
@rockinrobbie1985 2 жыл бұрын
Awesome video
@hailholyqueen
@hailholyqueen 2 жыл бұрын
I love you videos. Can you do one on why the hell drywall screw manufacturers can't make a product thats not full of metal filings?
@dereckthompson1572
@dereckthompson1572 2 жыл бұрын
Great content!
@Tuolite
@Tuolite Жыл бұрын
I learned a lot from this video.
@TheAxecutioner
@TheAxecutioner 2 жыл бұрын
For hanging ceiling.... hopefully, the metal studs for the lid are a little thicker gauge than the wall studs, eh?
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
Not if you don't have the right screws!
@Nocholas
@Nocholas 4 ай бұрын
Screw into the hard side not the soft side. When you have a seam, screw the hard side first and then the soft side. The hard side is the side with the face, and the soft side is the side with the open channel.
@alexosorio2590
@alexosorio2590 2 жыл бұрын
Un saludo Ben, ojala pudieras algun dia editar tus videos con subtitulos en español, soy un seguidor y te agradezco que comprtas tu conocimiento, he aptendido mucho con tus videos, acabo de sacar mi titulacion oficial de instalador de drywall, un saludo
@Hazel_256
@Hazel_256 2 жыл бұрын
Next time point or use images that highlight the location bc as a DIYer I'm still confused. My entire condo is metal studs and concrete but I need to screw in a closet.
@gamehulk
@gamehulk 2 жыл бұрын
Is there a reason why you guys rev it up to 5000 rpm then slam it home? I imagine this is a gun with a special drywall tip that disengages from the fastener when it hits home, but doesn't the nature of high rpm without a clutch mechanism contribute to stripping screws?
@vancouvercarpenter
@vancouvercarpenter 2 жыл бұрын
It tends to go in faster and easier when at full speed. Takes a little getting used to the technique but it's more reliable.
@conradcoolerfiend
@conradcoolerfiend 2 жыл бұрын
It’s a specific drill made for sinking drywall screws. It has a depth stop.
@psycleshift
@psycleshift Ай бұрын
Glue is too hard, and the steel is too weak. In the field is fine. The big problem is the too hard factory rolled edge. I have found if you reverse the screw and bore the rock first, it helps. But another observation is, rock is rarely layed down on metal studs like you would with a wood wall, its stood up the tall way with the metal stud. Unlike he did here.
@Joe-jv5mm
@Joe-jv5mm Жыл бұрын
Top Tip👍
@nicobayburtcanada8653
@nicobayburtcanada8653 2 жыл бұрын
New generation of steel studs are not even 25ga(.18 mil) now its like ,15mil which is thinner than 25gauge. Thats the problem. by doing that manufacturer saves %10 more
@davidkahler9390
@davidkahler9390 2 жыл бұрын
Ben's impression of the butthurt drywaller is dead on
@TapelessDrywallFinishing
@TapelessDrywallFinishing 2 жыл бұрын
👍👍
@HotspotsSoutheast
@HotspotsSoutheast 2 жыл бұрын
I don’t understand why anyone would build a house out of steel. Wood is a hundred times easier to work with, you don’t get shards of metal flying everywhere when you cut it, it’s not so thin that screws have nothing to grip on, it not electrically conductive so you don’t have to worry about shorts, the edges aren’t as sharp as razors, so many reasons to use wood. If you screw up a hole you can fill it with wood and drill again. You can glue it, you can nail it, you can screw it, hell you can use bailing wire if you have to. Metal lasts a long time and doesn’t rot. If you protect your house and don’t let termites in wood lasts a long time and doesn’t rot either. The advantages of steel over wood are negligible, not worth the hassle.
@frayedinsanity
@frayedinsanity 2 жыл бұрын
Steel studs are used in commercial buildings, not residential housing.
@soxnpats4lyfe
@soxnpats4lyfe 2 жыл бұрын
@@frayedinsanity we use steel in residential down south. Steel doesnt deal with the poor quality of 2x4s Steel doesnt cause screw pops Steel doesnt leave wavy walls Wood has to be treated prior to hanging Termites are a problem. Water damage can be way more of an issue. Id take metal framing allllllllll day over the issues we run into with wood framed houses.
@marjieyoung9570
@marjieyoung9570 2 жыл бұрын
I've found it's a regional thing. When I went to India I actually had a bunch of Indians asking me why we use wood to build our houses. (I'm from the Pacific Northwest, USA.) They reasoned that surely other materials like steel and concrete and tile and things like that would last much longer than wood, and besides that, "it's a waste of trees." But it's a different environment over there and trees actually were hard to find in the area I visited. The concept of using wood to build houses with was just totally foreign to them. They also have a monsoon season so I'm pretty sure if they built their structures out of wood they wouldn't last too long soaking in flood waters during the rainy season.
@tommygun5038
@tommygun5038 2 жыл бұрын
They have advantages over wood if at least 20ga. But I too like working with wood better.
Save time Cleaning your Drywall Tools...do only as much as you need to!!!!
14:56
Fine Thread vs Coarse Thread Drywall Screws
8:54
Vancouver Carpenter
Рет қаралды 66 М.
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 62 МЛН
Une nouvelle voiture pour Noël 🥹
00:28
Nicocapone
Рет қаралды 9 МЛН
Quilt Challenge, No Skills, Just Luck#Funnyfamily #Partygames #Funny
00:32
Family Games Media
Рет қаралды 55 МЛН
Мен атып көрмегенмін ! | Qalam | 5 серия
25:41
HOW TO  Build a metal stud wall
16:35
Siniat UK
Рет қаралды 2,2 МЛН
How to Wall Mount a TV to Metal Studs
6:01
Handyman Startup
Рет қаралды 952 М.
METAL FRAMING BOX HEADER
17:33
j sanchez
Рет қаралды 469 М.
How to Attach Wood to Steel
5:25
Next Level Carpentry
Рет қаралды 177 М.
Metal Framing - Tools, Fastening Methods, Fundamentals
17:33
ArhiDac
Рет қаралды 401 М.
Metal Stud Walling Made Easy ~ Knauf Performer
12:02
Skill Builder
Рет қаралды 219 М.
The Right Screw for the Job: A Metal Framing Guide
7:51
US Frame Factory
Рет қаралды 900
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 62 МЛН