Thule EVO Clamp WingBar Evo Roof Rack Overview and Install

[@rackattack]

🛒 Find Evo Clamp + WingBar options here: www.rackattack.com/thule/bare-roof-mount-rack-systems/ 🚗 Fit Your Vehicle: www.rackattack.com/fit/

[@JayJay-hb5rz]

Does it matter that the instructions say “without glass roof”?

[@rackattack]

@@JayJay-hb5rz Hello. Yes, it does matter, this indicates that a glass roof equipped model is not an approved fit. Thanks!

[@jrm8970]

For anyone having this problem, make sure you loosen the hex bolts on the clamps before mounting on the roof. My clamps would not fit in the proper locations until I did this

[@ayaraskovitch]

Thank you SO much for this comment!!! We were extremely confused and this comment saved us. Seems obvious in retrospect, but we're roof rack first-timers and probably would have been scratching our heads for a while without you!

[@rackattack]

Great advice and correct there are a lot of vehicles that the central bolt needs to be loosened off for the clip to wrap around the vehicle properly. One of my favorite how mechanically minded are you "tests" with new staff haha.

[@ryanhall9634]

Thank you!!!! I was stuck too

[@leepriebe4849]

Agreed lotsa doubling back on adjustments

[@hannahhasbrook8869]

I wish I had read this yesterday...

[@danawhite7052]

The best demonstration/explanation of this roof rack install that I've seen. Very well done! Thanks.

[@guillermofelix4734]

Thank you, could not have mounted roof rack without you🙏

[@marcyfogal7960]

Amazing. Your video was so so so helpful. The written instructions I received were nearly indecipherable. You made sense of the of the steps for me, and I now I am the happy owner of assembled roof racks. Thank you!

[@rackattack]

Glad it was helpful!

[@RKArchitects]

Thank you for this - It was the rubber inserts on the top of the bar that had me confused. I nearly tore off the wrong part. There is a strip that has small Vs on it - do not tear this off - instead dived the strip evenly down the middle! The clue was when you showed how the T bold slid down the middle of these two strips!

[@johnluckwell1174]

Like many others here, I struggled to understand the instructions, which I suppose are designed to be universal to any language. However, the video was clear and precise, even considering the language difference between American and my Scottish lol Thanks. :)

[@anneangersbach]

This was super helpful, especially confirming that I have to break the rubber lining apart down the center to actually install it as intended, since my installation guide was for the Thule wingbar, not the evo wingbar. Thank you very much :)

[@vah4k8]

Thank you! I did not notice this part and had been puzzled for hours.

[@JimMathieson1]

I bought the whole lot 598 carrier , the evo wing bar myself. Its a great second to none quality system. The only thing wrong was Thule instructions are very poor. Now I am fairly handy at building things but this was tricky to understand. So thanks for the demo as I didnt even know the end caps were swing away and thats the rack been fitted for a few weeks.

[@847MicRoss]

There customer service is very poor.

[@enricogrisafi9401]

Instructions from Thule are good, but I had to back off the torque screw on the clamp as far as possible to allow both clamps to fit at the same time and for the rubber feet to fit, when placing on the roof of the vehicle. Excellent video!

[@korbendallas1210]

Thank you for the detailed instructions. Does this metal mount scratch the paint?

[@jrm8970]

Thanks for posting this - much easier than trying to follow the paper instructions provided!

[@caroljudy100]

Great video demonstration and instructions. Since your videos were so good and your prices were comparable to other dealers I wanted to support your efforts by ordering from rack outfitters. Ordering process was easy, delivery was quick. Thank You!

[@nalietmiranda7450]

I’m thinking about buying one of these roof rack systems for my car and I have to say your instructions are excellent very professional and understanding

[@Stewy359]

Using ours for the first time today (got 2 of them). So good!

[@UnitedPebbles]

Ja Miranda. It like having a mini pick up feature?

[@afrikaansgospel3739]

Way better than the Thule company video which has no commentary.

[@rackattack]

Hello. Thanks for the positive feedback!

[@sean8081a]

Can the door frame bracket scratch the paint or does it have a soft coating?

[@bonobobros4960]

great job rack outfitters. got my roof rack complete with lock cores for $138 less than thule directly plus free shipping and great customer support including this tutorial. i hope this system is as great as I think it will be long term.

[@rackattack]

Thanks for the positive feedback, we appreciate your business!

[@UnitedPebbles]

How??

[@alisonloughran2925]

Thank you. Could not have done it without you.

[@rickstein6091]

Extremely clear and well produced tutorial. Thank you.

[@rackattack]

Awesome feedback Rick, we hope the system works great for you!

[@DanteDeGraaf]

Thanks for the video!! The clicking part was getting me a little nervous.

[@karljones9832]

Me too, 50 percent 100 percent what does that mean.

[@karljones9832]

Thanks for explaining the torque tool clicking. The manual isnt clear especially when you are screwing something metal (coated) to your new car. Our locks in the uk are included, but we probably pay more for the kit to start with. Thanks for the video

[@MarTeeNezNC]

This is a fabulous video and I've got my rack 3/4 installed on my car. Now what do I do if I "Y" setting for the rear bar says 35.5 for that slider underneath, but the clamps can't reach the edges of my roof at that setting? Distance from front bar is confirmed. I'm guess just wing it and split the difference so both feet are at the same setting and bar is equidistant on roof. It looks wonky. The rear bar looks way too far forward.

[@paulchevrier9961]

Very good video. You demonstrated the installation in a way that is easily done. Thank you.

[@rackattack]

Glad you liked it!

[@mitshumarner5870]

Very informative. With thanks. Question is the metal roof rail anchor padded to not damage the paint when it's torqued down?

[@YRDY]

Not padded, I assumed it had some sort of protection and ordered it.. Maybe gonna place some chair felts underneath. 😅

[@YRDY]

Never mind, there was already a similar question asked and answered. There is a P-Bax coating/cover over the bracket;)

[@spencer82rocks]

Thank you, I am thinking to buy a kayak or inflatable so then this is the first thing to purchase, we’ll explain and easy to understand, wow 😊😊

[@rackattack]

Glad it was helpful!

[@basecamplife5424]

I just put this on my Ram 1500..thanks for the video instructions!

[@gopibble]

Thank you. I definitely feel more confident in my upcoming install.

[@Rich_Juricich]

Great instructions! The printed instructions that came with the rack are really confusing.

[@jessehernandez3727]

Is this the exact same process as the Toyota CHR?

[@darrenrodd.]

How does it know the size to set the ends on ? Not all cars are the same width

[@alexmtyonline]

Que pasa al quitarlas?? no deja marcada la pintura por ir directamente a la lamina del auto?? o trae interior acojinado??

[@rackattack]

Los componentes que están en contacto con el vehículo están ruberizados para evitar daños en la pintura del vehículo. También se recomienda que las superficies que contacten con cualquier componente se limpien antes de instalar las barras.

[@konsul2006]

As a newbie who only wants to put a pair of skis on there, how do you do that? What makes the skies not just slide off? :)

[@lsarjant]

Paul I'm not sure which number door clamps I inserted, how do I take them out to put them in the correct place?

[@lsarjant]

Once they are in I can't see the serial numbers at the top

[@rackattack]

Hello. Push up on the bracket back into the foot, then rotate inward, this motion will allow the bracket to unhook and slide out. Thanks!

[@gamerkids6572]

@@rackattack Got it, thanks. Simple now I've done it, maybe a video would help.

[@rackattack]

@@gamerkids6572 Good suggestion, thanks!

[@noahfickel7698]

How do you explain the rubber foot pads lifting free after tightening?

[@rackattack]

Hello. That would usually be caused by incorrect foot placement on the bars. The inner edges will lift if the feet are too far out. Thanks!

[@slimatmim]

So I was wondering. Is it ok to install small clean vinyl in the area where it clamps to the car to prevent from gouging the paint.

[@rackattack]

Hello. Generally, it is not necessary as the rubber is specifically engineered to be protective the the surface, however, 3M does manufacture a clear vinyl adhesive that could be used for added protection. We do not have a specific part number or source for this vinyl as it is not a method that is commonly used. Thanks!

[@uhN0id]

I have a 2024 Impreza RS and the mounting points for the rails I am getting (SSD brand - I didn't want to do fixed point/direct to roof with the crossbars) are about 45 inches at the front and 43 inches at the back. What length Wingbar should I get? Thanks for the video, it is incredibly helpful!

[@josephdburdick]

If you added a wind fairing would you still be able to operate the moonroof

[@cristiannistor1076]

Hi! I have a question before ordering this product. How will behave in time the attachement on the curve of the door. It is metal on metal. There will be scratched of the paint at the installation or afetrwards? Thank you!

[@cupydon27]

Hi Cristian! It might scratch the car paint. You must follow the Thule guidance exactly to avoid problems. For extra protection, you could install a paint protection film PPF like 3M Scotchgard or similar.

[@nicholasspeers1859]

Best tutorial on this I have found, thanks.

[@levkomed]

Hi, is the length between racks and from front to window same on all cars? I have Jetta 2017

[@surfthecure28]

I recently purchased these racks and am having a lot of issues with the rubber pad staying flush to the roof of my vehicle in addition to having the bars hang evenly on each side of the car... any advice?

[@tylervandergriff6559]

Is the width between the front feet wider than the feet in the back? It looks like it’s saying my front should be 36 and my rear should be 30,5

[@haranic]

Hi. My 2020 Nissan Kicks Sv has no roof rack rails. So I need one of those things in your video. And i prefer thule however if it has no product fits to my car , i don’t mind other company’s product. In this case, which type of product I should buy? I mean , the specific model number. Please let me know what to buy

[@ArcaneZay]

This video was very helpful thanks!

[@rackattack]

Glad it was helpful!

[@nunogaisita1044]

That car don't have a hole to fix the bracket with a screw, to be more safest?

[@pinoybikers8834]

Will these fit on any door clamp car?

[@DoctorGash69]

Does it matter which foot goes on which side of the car/door?

[@rackattack]

Hello. The feet are all the same until the fit kit base pads and brackets are attached, at that point the position is critical to the proper fit. Thanks!

[@robertswahl225]

Why would you put the sticker on the back, exposed to the elements? The instructions clearly indicate to put it on the inside on the rubberized clip. Where it has a cover over it. And won’t come off. And is pretty much always connected to the clamp.

[@robertswahl225]

Not even on the rubberized clip. On the interior clip of the clamp itself...

[@arcticdepth]

Does the rubberized, fitted footpad have to be flush with the car? I got mine installed and two of them aren't completely sitting on the car as the diagram shows.

[@stevescottukss]

Thanks for this great vid. How does the bracket part that sits in the door frame not damaging the paintwork though please? I can't see rubber on the inside.

[@rackattack]

Hello. The metal door frame bracket is entirely coated in Pebax rubber for both grip and protection of the finish. Thanks!

[@stevescottukss]

@@rackattack Thanks so much. I shall have a go at fitting it this weekend :)

[@jonathandance7372]

Thank you - might I suggest the rubber feet are slighlty out of position relative to the bodywork?

[@gilbertorobles3321]

Will this damage the rubber on the door seal of the car?

[@Teganjb55]

No

[@jennifer06131]

Missing little installation details. I figured it out how to follow all measurements to get the right fit.

[@rackattack]

Glad you were able to figure it out, Jennifer! We are also available anytime you have installation questions, as our installers have a lot of experience

[@kylehooper2981]

Why does the fit kit I got for my feet not fit the feet? The ones I have, have two 'spires' coming out that insert into the uprights. Maybe it is an older model? And the clips that attach to the car are very short. Is there a fit kit for my car that works with these? Am I looking at it wrong? Because it does not seem like it fits or works - at all.

[@rackattack]

Hello. The past foot packs are not interchangeable with the current fit kits and vice-versa. The EVO Clamp Fit Kit, must be use with the EVO Foot Pack. Please use our guide to see the parts that will work together on a vehicle: www.rackattack.com/wizard/

[@karenbowser1429]

This video was extremely helpful but my issue is after installing, drove the car and it’s super loud from the wind so I’m thinking did we do something wrong or what could it be?

[@rackattack]

It's important to install the rubber on the underside of the bar from the foot to end cap, without this rubber you'll get wind noise. Hope this does the trick!

[@clanmac66]

Thank you, great demonstration.

[@rackattack]

Glad you liked it!

[@Mafioso1731]

Is the pro bar better than the Evo bar despite it being more popular? Also how does the Evo bar compare against the edge bar?

[@humbertolopez4215]

What about the scratches on the car paint?

[@rackattack]

Hello. All contact points with the vehicle have protective rubber. It is good practice to remove the rack from the vehicle when it is washed and waxed. Thanks!

[@cesartrevejo6562]

I have a Kia Sedona van, will the clamps stay secure and not interfere when sliding mechanism is operational?

[@rackattack]

Hello. We don't see a stock fit for a bare roof Kia Sedona, the stock fit requires the vehicle to be equipped with the factory installed flush side rails. The system for this would attach to the side rails and not interfere with the sliding mechanism. Here's our guide for more information: www.rackattack.com/fit/kia/sedona/ Thanks!

[@Gundam-bruh]

Isnt that hook ok the door going to scratch the car??

[@rackattack]

The components which come into contact with the vehicle are rubberized to prevent any damage to the paint of the vehicle. It is also recommended that any surfaces which come in contact components are cleaned thoroughly before installing the bars.

[@papillon5537]

Thanks for sharing, do you have recommendation for Golf GTI?

[@rackattack]

Do you have the 3 or 5 door version? Also, please let me know the year so I can get the most accurate fitment

[@ManoloDaza]

Great video, thanks! I see you've installed Thule EVO Clamp WingBar and also in a different video the Yakima BaseLine + JetStream. Once completed the installation, for the next times you want to install&remove the roof bars, which ones would you say is more comfortable & quick? Example, I want the roof box just for the trip, once in there, I'll take everything off and install it again on the return trip. How long would it take? Thanks in advance,

[@rackattack]

Hello. The EVO Clamp has fewer adjustment making install and removal faster. Expect about 2 minutes to remove the rack and 10 minutes to reinstall. Thanks!

[@ManoloDaza]

@@rackattack Thanks a lot!

[@filipalexandru3129]

quick question. I am about to buy this set of racks for a civic x sedan 2018 with sunroof. The Problem is, that the Thule sent me an email that for this type of car(with surnroof) the racks won;t fit....WHY? I ve seen a lot of cars with sunroofs and roof racks and have had a problem in years. Is that only as a safety thing or sth? because from what I saw, the sunroof opening/closing is not affected at all. Thank you very much for the response.

[@santoslorenz]

Would this mess up my paint?

[@rackattack]

Hello. The vehicle specific fit kit uses custom shaped rubber bases and Pebax rubber coated door frame brackets both are designed to fit the contours of the vehicle while protecting the finish.

[@thetwotuff]

Great video, the bars look like they're the opposite way around, or is it me? Wouldn't the tapered end be pointing the way you are driving to be more aerodynamic??

[@jonjaaay]

i get what you're saying. but the tapered part should be pointing towards the rear. check out the Thule site for photos of the product as it shows the taper pointing the back. think of airplane wing design as well as bicyclists who wear those helmets with the long tapered tails.

[@rogerpennington7677]

I have these and pout them on as you suggested, with the tapered end pointing forward. They were so noisy that I called Thule, who was very kind in helping me turn them around the correct way. Problem solved!

[@PurposeTravel]

It's a wing like an airplane. Tapered edge to the back.

[@petercho4939]

Great video! would the roof vehicle specific metal clamp mark up the factory paint from being on the car for a long period of time? If so, can you install a protective 3M layer on the contact point before mounting the foot clamps?

[@rackattack]

No need. The metal clips are completely covered in a protective P-Bax rubber. This provides grip and protection to the vehicle.

[@847MicRoss]

My rack has moved a little bit and it didnt harm the paint. A clear vinyl isn't a bad idea though.

[@lilwindigo1000]

i have a corolla hatchback, the "x/y scale" on the manual is universal, theres no indication for my car so i dont know at all the distance i need to have

[@rackattack]

Hello. According to Thule's fit guide the current fit kit for the TOYOTA Corolla Sport, 5-dr Hatchback, 19- is KIT145209, here's the manual which includes all the necessary measurements for the proper fit. www.rackattack.com/public/product-instructions/145209_521-5209-02.pdf Thanks!

[@RobertSmith-di5ll]

fantastic - just what I needed

[@zachrene6972]

Will that work on an Hyundai elentra 2016 sport please let me know

[@rackattack]

Hey Zach, Thule has not made a fit kit that is compatible with both your 2016 Elantra and the new Clamp towers, but if you reach out or check our fitguide on rackattack.com we can look into the other brands that do have a fit

[@Thienhuong72]

Hi! Thank you for the info to install it.I did the same and easy to follow steps.And I have a question now.Please tell me how to remove the fit kit from the evo foot clamp.Because I would like to switch the cross bars to new car with different fit kits.Thank you.I appreciate it.

[@rackattack]

Hello. The door frame brackets can be removed by pushing upward, then rotating inward then pull down. The rubbers bases can be pealed off of the pivoting plastic bases. Thanks!

[@Thienhuong72]

@@rackattack thank you so much.Wow that s easy to remove.I appreciate it.

[@rackattack]

@@Thienhuong72 You're welcome!

[@alexanderromero3752]

What is the correct bar length for the new 2020 Nissan Sentra and what clamp set? (kit Clamps)

[@ericbrasel9779]

So I have this exact rack for my 2019 camry, when you place the feet on the bar is the front supposed to be a little wider than the back or both the same, mine showed 39.5 for the front and 37 for the back if I read it right.

[@rackattack]

Hello. The foot position on the bars is almost always different front to rear and usually spaced wider at the front. Thanks!

[@razerrazer8242]

Feets are purchased separately or included in the package with roof rail

[@rackattack]

Hello. Foot pack, fit kit, bars and locks are sold separately and can be configured using our vehicle guide here: www.rackattack.com/wizard/

[@razerrazer8242]

@@rackattack Thule or farad roof rack is better

[@jabespangs]

Any tips/videos on how to replace fitkits? I wanted to use my old evo roof rack on my new car so I need to remove the old fit kit and put in the new one.

[@rackattack]

Hello. Yes, the base pads will peal off from around the perimeter of the foot base, to remove a door frame bracket, push up on the bracket into the foot, then push inward, then down, same for each foot. Thanks!

[@rudigerbrightheart7304]

Great video, very helpful instructions! I have the Wingbar Evo 127 and I have a problem pushing the plastic pieces at the end of the bars. I have double checked if the side was correct. Now there is a little gap of 2-3 mm at the borders and this may be cumbersome with water infiltrating. Any helpful advice would be appreciated!

[@rackattack]

Hello. Check that the rubber on the top and bottom slots are not interfering with the end cap fully connecting. Thanks!

[@IAMBCM]

Fits in 2018 Toyota Camry ??????

[@NotJanine777]

Just bought this kit - great video - thanks.

[@traveler7353]

Has it worked for you? With kayaks? Luggage box? At highways speeds? I bought something similar and haven't used it yet

[@chatimer]

how good are these racks for canoes? Anybody have any issues? Really thinking about getting one of these. Do they fit jettas? Great video 👍

[@rackattack]

Hello. Yes, there are options for Jetta's and there are carriers that will help safely transport a canoe. Here's a link to our roof rack vehicle fit guide: www.rackattack.com/wizard/

[@mollymartian9969]

i wish i had watched this one before watching the Thule one. i pushed the feet in and now i can't tell which one is which. arg.

[@ferdinandcabalquinto335]

question sir, the cross bar connected to the 4doors theres a space between the rubber and the cross bar lock, its possibly that the water get in inside the car? or water flow from the upper door inside coz of connection of the cross bar..thanks.

[@rackattack]

Hello. The door frame brackets are custom shaped to fit the door frame without gaps and the door will have multiple wind and water seals to stop water from entering. Thanks!

[@ferdinandcabalquinto335]

@@rackattack okay tnks..god bless..👍

[@japohn]

Is there a part one to this video? It's like having someone give me their impression of the instruction manual.

[@rackattack]

Hello. No part one, this video is to provide a visualization of the steps shown in the instructions and serves as a supplement to the instructions. Thanks.

[@MrTomEhunt]

Excellent explanation of the whole process. I've got the same car too, so helped massively. Thanks.

[@Will34TV]

Liked the video! Question is, can I put a snowrack right on this, or do I need another bar?

[@rackattack]

We offer the full selection of Thule snowsport carriers to fit the Thule roof racks: www.rackoutfitters.com/thule-ski-snowboard-racks-1/

[@annale1957]

What length are these bars???

[@robpowell9162]

Hey great video! Really easy to follow! I do have a question, in case you read these.... I have just got a 2018 Vauxhall Insignia Grand Sport, and I have the right feet and pads, but my bar is "only" 127 rather than the reccommended 135. There's definitely more than 3"/8cm overhang in total for the Insignia, so can I use the 127 bar? Instructions say 46/E for spacing, can I add 1.5 each side and go for 47.5? (it's not chear if it's inches or cm mind!) Any help to retrofit would save me a tonne of cash! :)

[@espacotoc820]

I put the clamps wrong. How do I take them off please?

[@rackattack]

Hello. Push the bracket up into the foot then rotate the bracket inward, then down and off. Thanks!

[@juliussdelacruz447]

Thank you Rack Attack! Do you have any special tips if I'm installing on a Mustang Mach E Panoramic fixed glass roof?

[@rackattack]

Hello, after reviewing the manual for the vehicle, we see no special notes or instructions related to the panoramic roof installation.

[@juliussdelacruz447]

@@rackattack Thank you so much! I appreciate the info.

[@kuyaboyred]

Can you guys please install one onto 2020 Camry xse

[@ramirobriseno3353]

I have a Honda Civic 2015 sedan and I want to install a top rack

[@rackattack]

Hello, here is a link to roof rack options for your vehicle: www.rackattack.com/fit/honda/civic-civic-hybrid-4dr/2015/

[@tomsimonis]

Thank you for the superb explanation!!

[@rackattack]

You are welcome!

[@duncanlatter9060]

How do you remove this if you don't have a key

[@rackattack]

Hi Duncan, if you remember the key code we do sell replacements on our website. Alternatively, you can pop into any of our stores and our Gearguides will be able to find the right key match for your setup. Thanks!

[@alexjoz]

So, they are on the different height? I mean front bar is lower than back one as the car is really curved to the front?

[@alexjoz]

@Rack Outfitters thanks. Strange, but I was not able to get them aligned well, having 680mm bar to bar length. Had to put it further to the tail, to gain the same height. I used 5043 kit. oO

[@rackattack]

Hey Alex! The 5043 Kit has very specific fitting instructions and isn't adjustable like that. Moving the bars front or back could cause them to slip and fly off as the clips and pads are engineered to sit at a very specific location. With the curves of some vehicles roofs visually some roof racks are hard to line up but Thule does a lot of testing on their products and all the various cars. You'd be able to put a paddle or surf board directly on those bars though! Its very important for warranty and safety, for both you and the people driving behind you that all roof racks are installed as per the manufacturer's guides and checked as per instructed.

[@ZaneLeeGold]

How do you open the doors

[@rackattack]

Hello. The custom shaped door frame brackets to not interfere with the operation of the doors or the door seals. The brackets are metal with a protective rubber coating to provide grip and a protective interface with the door frame. Thanks!

[@Christian.Marquez]

Just got the clamp edge attachment for my bare roof.. my concern is that the clamp will scratch the paint and build rust… anyone having rust issues?

[@rackattack]

Hello. The door frame brackets are coated in Pebax rubber which is specifically engineered to provide grip and protection to the surface finish.

[@earthcomedy]

well..that looked pretty easy. Thanks

[@cheefussmith9380]

How much weigh can these things support? I keep seeing adds for those roof nest tents...doesn’t seem like these could hold that kind of weight

[@rackattack]

Weight capacity is vehicle specific, use the Thule fit guide to determine the max load and tent approval. Thule, Yakima, and Rhino-Rack all state that their clamp-on type roof racks are NOT approved for the rooftop tent category.

[@fahdhli]

Is it fit on all cars?

[@rackattack]

Hello. These racks are vehicle specific, configure a rack for your vehicle using our guide: www.rackattack.com/wizard/ Thanks!

[@TerryMcGearyScotland]

Not mine unfortunately but thanks for letting us see this one.

[@rackattack]

Hello. We have over 2000 rack videos, try our channel search to find content that's most helpful to you: kzbin.info Thanks!

[@jackmccallum335]

Thanks so much for this video. Ordered from your site!

[@lindonandlisa8114]

Another outstanding video thanks so very much