The first owner of my 2008 endeavor and it has all highway miles at 316,000 the only thing I replaced was the timing belt and radiator.
@TD04_Trav2 жыл бұрын
13:06 how am I supposed to do this? The plunger is already extended there is no locking pin and i can’t get the plunger to go down and line the two holes up???
@nunkirider87382 жыл бұрын
@ ttravis88t - You have to use a vise to compress it and insert a pin or if you don't have one, a C-clamp and a wood used to protect the plunger can be used to compress it. Just be careful the hydraulic tensioner might fly off. Good luck...
@practicalporters3 жыл бұрын
This video just like the first one that he did four years ago is fantastic. I just put our Mitsubishi back together and test drove it just now and works great with the new timing belt. Thank you thank you thank you for excellent detail and close up video shots of intricate important parts. Your notes saved the day.
@AstonSubstantive15 күн бұрын
You did a fantastic job on this video. Thank you.
@JackJockette7 ай бұрын
Hahaha...you show the harmonic balancer pulley bolt as finger tight...just wait till some of you see how bloody tight they do that bolt ...you will need a serious rattle gun to get it out...a Milwaukee will do it....then again we had to get a breaker bar and lower the full weight of the car on it to undo a really tight one......good luck boys and girls
@neilasd30434 ай бұрын
Never had crank bolt on a Mitzi that hard you need more experience
@johns63318 ай бұрын
Great video. To be commended.
@davidw.51855 ай бұрын
What is the recommended mileage for changing the belt? 😊 ty
@nunkirider87385 ай бұрын
@davidw.5185 - In Mitsubishi Endeavor owner's manual, it says every 60,000 miles...
@CarlosSanchez-nz7iy4 ай бұрын
Great video 👍
@joshnelson76533 жыл бұрын
well, all i can say is thank you. Hopefully this is just like the 07 eclipse/// I think im the only one who takes 3 hours to watch a 30 minute video... Thank you soooo much for actually editing and adding in texts every step. It seems to be way easier then my 1g 4g63 timing i did .. Ill be doing this tomorrow.
@nunkirider87383 жыл бұрын
@Josh Nelson - Good luck on your D.I.Y... and thank you for watching the video.
@joshnelson76533 жыл бұрын
@@nunkirider8738 thank you.. Im gonna hold of on it for a couple weeks now due to i was so intrigued by the video and watching and rewatching, writing down notes, taking screens shots that i totally spaced out watching a video on removing the water pump...So, instead of spilling coolant on my brothers garage floor(minnesota climate, he has a heated garage) i decided to tackle the serpentine and pulleys, plus my front brakes..as the rears will be friday.. Rusted bolts and such turned an hour job into 5.. But, This will be my go to video for trouble shooting as i like how you stopped and point out certain little things. Thanks again though
@thomasnichols48702 ай бұрын
Was it actually easier than a 4G63?
@joshnelson765318 күн бұрын
well, about the same.. but I've used this video and the pics a few times now .water pump replacement cause duralast, another was to check the water pump. I changed a timing belt on a 4g63 by candlelight in winter. so once you get the hang of it.. ;)
@sreckosvalina95472 жыл бұрын
Nice informative video. I'd just like to ad my take on this job . The grenade pin will not spin freely if the tensioner gap was 5.9mm because the plunger would come out a bit however with a range between 4.8 and 6mm the tension would still be within specs even though the pin dosent spin freely anymore at say 5.8mm.
@fletcherhodge66003 жыл бұрын
I hope you get a rattle gun for your birthday. And a flexi extention 😊 Thanks for the video.
@xbgtfella3 жыл бұрын
I found tdc on no 1 (left bank front) manually spark plug out with long screwdriver and old cam belt setup sprockets are both bout 4 teeth off clockwise equally from cam engine pointers. Is this usual? Havent checked crank sprocket marks yet as i was winging it, then it got dark, then found your video. Old cam belt still on. Any ideas
@nunkirider87383 жыл бұрын
@xbgtfella - I have no idea… however, while turning the camshaft clockwise, and as screwdriver starts to go down, turn the camshaft back counter clockwise till the screwdriver goes back to the highest point again and note where your TDC marks are… Thank you for wacthing the video...
@ronrubendra50053 жыл бұрын
Awesome video - thank you - doing this to my 6G75 Mitsubishi in Australia
@donovantan59592 жыл бұрын
bump my right camshaft wheel while replacing new timing belt. can I rotate it back to timing mark? Crank is at TDC. Right Camshaft is on timing mark.
@nunkirider87382 жыл бұрын
@Donovan Tan - Watch the video again and go to 18:17-18:39. Thank you for watching the video.
@BOSSLADY-x10 ай бұрын
thank you so much for this video
@simonmichalowski73663 жыл бұрын
Good video mate I like how you make your own tools I would like to hear some commentary from you but over all 5 Stares I wish I had a mate like you Thanks for all the advice will look for other videos from cheers from the land down under Simon Michalowski😊👍👌
@nunkirider87383 жыл бұрын
@Simon Michalowski - You are welcome and thank you very much for watching the video 😊👍
@dillondowney5247 Жыл бұрын
Thanks! This video helped a lot.
@jcoleman89692 жыл бұрын
My crankshaft mark is off a tooth but both camshaft marks line up with TDC. Question, with belt removed can I just rotate the crankshaft a tooth clockwise to realign with the with the TDC mark
@nunkirider87382 жыл бұрын
Yes. But have to perform proper TDC alignment procedure check again after you install the timing belt.
@jcoleman89692 жыл бұрын
@@nunkirider8738 awesome thank you!
@sierrapepin4 жыл бұрын
I have to ask, you’re from Minnesota, right? What year is your Endeavor and how many miles?
@nunkirider87384 жыл бұрын
@Sierra Pepin - it is a 2004, and 215,000 miles. Thank you for watching the video.
@practicalporters3 жыл бұрын
Wooooow, mine is just a kid at 2005 with 150k!! Love this suv!
@sierrapepin4 жыл бұрын
Thank you!
@bobadams36613 жыл бұрын
I purchased a new timing belt tensioner (Aisin #BTM-500) for 2005 Endeavor. New out of box the pin will turn but not spin easily as you show. Is it defective or should I install it? Thank you, great video!
@nunkirider87383 жыл бұрын
@Bob Adams - Out of the box, that pin is under tension and will not turn when flicked, the pin will only spin if flicked when it is already properly installed. Thank you for watching the video.
@bobadams36613 жыл бұрын
@@nunkirider8738 But @18:40 you spin the pin before torquing the tensioner. Isn't that same condition as "out of the box"? It looks like all you did was bolt the tensioner to the motor.
@nunkirider87383 жыл бұрын
@Bob Adams - If you just have installed the tensioner and the timing belt or released the center bolt for re-torquing, the pin will be tight to turn and will not spin when flicked. What I did is that I turned the tensioner pulley counter clockwise with the tool MD998767 on a ratchet (not with a torque wrench as seen at 17:21) until I can spin the pin freely and then tighten snugly the center bolt with a box wrench to hold it in place (which I missed to show on the video). At this point I know that the tension that is applied to the tensioner pulley is already at specs. Then I did the procedure at 18:40. My apologies for the confusion and thank you very much for watching the video.
@drumsnbass4 ай бұрын
Great video! I might just pay to get mine done. How many hours should this take?
@ВасилийИванов-я8п4 жыл бұрын
Всё очень классно показано, как будто рядом с тобой разбирал. Живу в России. Endeavor 2004 года. 109000 миль. (Если не скручен)😄Спасибо друг!!!🤝👍
@nunkirider87384 жыл бұрын
@ Василий Иванов - Спасибо за просмотр видео, мой друг.
@sumangamer61143 жыл бұрын
;
@douglase44702 жыл бұрын
Noted. Thank you very much. I appreciate you work. DEE