TinyHawk 3 HDZero Build | The Whoop You Never Knew You Wanted

[@vernelfpv]

I never knew it could be that easy. thanks brother for this one

[@OneManUnmanned]

Thanks, I appreciate that. It's not bad at all, it's just those darn small screws.. 😆

[@vernelfpv]

@@OneManUnmanned i just got nervous at that wire you had to cut hahaha

[@dapitbull2009]

Me being an audio guy as soon as you said you’re going to use yellow for your audio. I was thinking. Yes!!!

[@brundle_fly5123]

Nice clean build! I wouldn't have tried that frame, but you were up to the challenge!

[@OneManUnmanned]

Haha.. thanks.

[@soursham]

You made it look easy. Great video 👍👌

[@OneManUnmanned]

Haha, Thanks.. It was anything but easy especially when filming a well. The tiny screws are extremely difficult to work with. Thanks again! 😊

[@vernelfpv]

Man i can't wait to watch this hahaha

[@nvincenth]

fantastic, thanks!

[@OneManUnmanned]

Thanks Nathan!

[@TechOffZedOn]

great video, thanks! I can't crush flip (turtle mode) with my Tinyhawk 3, it just brake dances all around on it's back. Does it work for you? Are the motors too weak for that?

[@gnafin]

THis will be good to try as my flight controller died. i just check on the part list and no stock. thanks i will try this when i can find a controller.

[@OneManUnmanned]

No prob.. Parts are hard to find these days. Get them while you can.

[@gnafin]

@@OneManUnmanned i got the parts. what file did you load on the controller?

[@OneManUnmanned]

I used the Metor75 CLI since that’s where the FC came from, and that drone is similarly sized to the TinyHawk 3. I later changed the tune, using the Presets tab in BetaFlight to “UAV Tech - Whoop(1S & 2S)”. I also used the HDZero VTXs Presets in the “Presets tab of BetaFlight to configure my VTX. I’ll link the Metor 75 CLI below if you want to use it for basic configuration, but I’m now on the UAV Tech Whoop Preset. support.betafpv.com/hc/en-us/articles/4408029285017-CLI-for-F4-1S-AIO-5A-FC-ELRS-2-4G-2021-

[@gnafin]

@@OneManUnmanned what did you pick for the PWM?

[@gnafin]

i got it working but the props are hitting the battery. did you have a clearance problem?

[@winder6]

Great build thanks for sharing 👍

[@OneManUnmanned]

Thanks, I appreciate that, Bryan.

[@benkimmitt]

I noticed the extra space under the battery. Very nice. Did not know about the Gyro issue. Will the firmware update fix it or once it’s done it’s done.

[@OneManUnmanned]

The firmware does not fix it, just prevents it from happening. If you've already powered it up and notice no issues, then you should be fine.

[@benkimmitt]

Have you ran across any good pertunes for the th3.

[@OneManUnmanned]

I’m using the “UAV Tech - Whoop (1S - 2S)” Preset and its working OK so far.

[@benkimmitt]

Very nice. Got mine last year was not much for mods then. Time to look in to it.

[@J.D.Vision]

Is there any way to just change the camera system to HDzero if you already have the Tinyhawk, without changing everything else, could you do a video of the simplest way to upgrade just the camera system? I personally have 5 analog Tinyhawks.

[@OneManUnmanned]

No, you can’t just change the camera. Your factory camera is analog while the HDZero is digital. You’ll have to change the camera and VTX at the minimum to make this system work.

[@J.D.Vision]

@@OneManUnmanned • Awesome.

[@jlipp8748]

How easy would it be to install the HDZero camera on an already built Tinyhawk 3? Does it help a lot with the annoying static picture you get when flying with the original camera and setup the TH3 comes with?

[@OneManUnmanned]

You can’t just add an HDZero camera to the existing analog setup. You’ll have to add a new HDZero VTX as well as the camera.

[@northerntierfpv8947]

super cool.

[@OneManUnmanned]

Thanks!

[@Shish-Kabob]

Really cool but I have a question, (totally unrelated) I really want to get into FPV so I want to get the TH3 but I feel like they might make a new model soon so should I buy or wait?

[@OneManUnmanned]

I do not know if there is a new model coming. Companies like to change/updated their products often to integrate new technologies. The TinyhawkIII 3 has been out for almost a year now, but I don't know EMAX's roadmap. My advice would be to choose a drone that you're comfortable with and like, then buy it assuming there will be no updates.

[@Shish-Kabob]

@@OneManUnmanned ok thanks

[@eprohoda]

you did ttop footage~One-:))

[@OneManUnmanned]

Thanks!

[@richardguerra7409]

How do you change the motor?

[@OneManUnmanned]

What do you mean? It's the reverse as installation. Just unplug it from the Flight controller and unscrew the 3 mounting bolts.

[@richardguerra7409]

@@OneManUnmanned ty bro

[@taxigalaxi]

What equipment du you use?

[@OneManUnmanned]

What do you mean? To film, to solder? All the parts for the drone are listed in the description.

[@taxigalaxi]

@@OneManUnmanned For soldering and flying

[@manwithgutz]

elrs?

[@OneManUnmanned]

Yes, ELRS

[@redcobra1246]

sEcOnD

[@OneManUnmanned]

I'm fourth, surprisingly

[@porshacarroll9600]

I love tinkering... Do u have a Facebook?

[@OneManUnmanned]

It's in the about section of my Channel.