Important rotary mower tips! John Deere 4066R and Frontier RC2072 tractor mower!

[@PJ-uv9fr]

I love the maintenance videos - they show you appreciate your equipment!💜💜💜

[@TKCL]

I sure do and I want it to last.

[@roberthermsen724]

Ruger the inspector is on the job. That was funny him inspecting your blade then looked at you tell you that you did a great job after you finished sharpening.

[@TKCL]

He checks out everything 👀

[@larrykusler5294]

I was right. Andrew once again you did a terrific job of passing on great information to your subscribers. You do a great job of maintaining your equipment in near new condition.

[@TKCL]

Take care of it and it'll take care of you.

[@mikerichard-FOPA3]

Andrew, Another great video, I love the way Ruger supervises your projects.

[@TKCL]

He makes sure I don't miss a thing.

[@bobgray617]

I love Ruger's wrapped attention. My lab will lay her head down on my desk or project like that too. It usually pays off for her by getting petted.

[@TKCL]

He's all about his attention, until he gets hot. Then it's off to a shady spot to snooze.

[@kevinbrewer2141]

My dad has an old brush hog that doesn't have any flex in the hitch. On way get around this issue is unhook the top link. I probably need to make a flex hitch for it.

[@TKCL]

I've seen those bend badly hitting holes, hills or going over really uneven ground.

[@josephcampbell007]

Rotary mower inspector Ruger approved of your maintenance. I love how Ruger wants to be apart of everything you do.

[@TKCL]

He's always checking behind me.

[@roydenheimdal]

A trick I learned from the mechanic that delivered my rotary cutter, is to use an allen wrench to set the slip clutch spacing. If you need 4mm, just grab that size allen wrench and use that as your feeler gauge.

[@TKCL]

Your exactly right, I remember hearing about that years ago.

[@langstonrowe8243]

Don't forget to pull your PTO shaft apart on the brush hog and grease it, very important!!!

[@roughcutscanada]

Great video! Thanks for this. I have the same tractor and brush cutter. Now I have more information to service the slip clutch. You just saved me $$ to have the slip clutch serviced at my dealership. 👏👏

[@TKCL]

Glad you enjoyed it.

[@FlightBandit72]

Lots of great info on brushbeater maintenance and adjustments. Now I know what that pto height adjustment knob does. Been looking to buy the 40 series tractor and thought I better watch this video too. Glad I did!

[@danl370]

Good video, it’s a good reminder about keeping up maintenance. Don’t listen to what they’re saying about other brands of impacts, stick with Dewalt and get the newer 20 volt max, I have it and works great, very impressed.

[@TKCL]

Oh I'm definitely sticking with dewalt, I already have all the batteries and those tools have treated me very well for decades. No point in switching brands what I've been using hasn't let me down once.

[@mstrickk1]

Tekton was one of the manufacturers of Craftsman when they were a Sears brand. One thing I would add is to clean the deck on these mowers. Here in Florida moisture finds everything, including the dirt and debris on top of the deck. Once it gets moist it stays moist, which starts rotting the metal. Running heavy duties, we've sent rocks and logs through the deck into the tractor a few times on many different decks, and had to patch everyone we've ever owned.

[@TKCL]

Agree with you on the cleaning.

[@dubs3400]

Thank you for this very informative video. I have a 2060 Frontier with the floating bar and will definitely pay attention tomorrow as to it’s position. I too, remove the blades to sharpen them while it takes a few minutes extra, I find I get a much better edge instead of crawling under the deck. Thanks again!

[@TKCL]

Glad it was helpful!

[@larrykusler5294]

Hey look, I finally made it first. Yet another extremely informative video.

[@TKCL]

4th my friend 😬

[@billybrown1979]

boy ruger was listen while you was talking and making sure the blade was sharpen correct. now all you have to get him to drive the tractor that would be kool. SAVANNAH TN.

[@TKCL]

Hes working on it

[@hammerslap5639]

Somethin else super important for maintenance on equipment is painting. Any welds, surfaces, or cavities where moisture can settle, basically anything that isn't a wear surface needs to be touched up if you see the paint getting thin or rusty spots forming. especially after you make semi-permanent adjustments like how you adjusted the hight of that trailing wheel arm, id give it a shot of paint where it used to sit since now thats most likely just bare metal.

[@TKCL]

Very true, these rotary mowers are notorious for rusting out.

[@InTexasMatt]

Ha! Same toplink here. I can't stand adjusting it. I've been looking at sharpening our blades.

[@TKCL]

Such a dumb design, yet another engineer that's never operated a tractor. 🤦

[@radmilamiljanic5977]

Your experience will help many! And you have so many useful toys ( yes, Mr Gray, I know it is pronounced tools:))))

[@TKCL]

TOOLS!

[@pampilgrim2274]

Hi, Andrew! You are very meticulous in the care and maintenance of your equipment. Ruger is a good supervisor.

[@TKCL]

He's a great dog.

[@skippyjl1]

Absolutely excellent video.. I have the same brush hog. my problem is it shakes real bad when I engage it. I cannot figure out what’s causing it. And this is the wrong time of year for it to not be working. Any ideas? Thank you.

[@JR-rx2ke]

Try some Loktite Silver Grade Anti-Seize. Also, if you do not have an air or battery 3/4 or even a 1/2 inch impact wrench, then get one.. If you get 3/4 inch it will work with you current set of sockets. Love your videos.

[@TKCL]

I have all 1/2 air and electric impacts. Thanks for watching.

[@JR-rx2ke]

I figured you did, as you seemed to be very competent and knowledgeable. I was just feeling sorry for you having to use wrenches to remove those blade bolts.😀 I've never seen bush mowers that permitted blade removals from the top. That would have made my lif a lot easier, and I would have sharpened the blades a lot more often.@@TKCL

[@lakepinesfarm1394]

For checking oil with no dipstick, I use a cut off of string trimmer line.

[@TKCL]

Not a bad idea

[@parkland4530]

In my experience the blade bolts and nuts can be almost or impossible to remove. They can also be extremely difficult to install. Some blame a condition called 'Galling' which is when the nuts (particularly lock nuts) actually weld onto the bolt due to friction. Impact wrenches can exacerbated the problem. Anti seize is a must. Check it out..

[@Tripring2000]

Good thing your tractor is air conditioned when you are mowing with it. Heat index reached 124.5° here today around 1:30 pm today. 🥵🥵 Be careful in your shop as well as hot it is right now.

[@TKCL]

I've been working on a deck in full sun the last two days. It's beyond miserable and dangerous. I'm taking tomorrow off for another job that has air conditioning 😉

[@Tripring2000]

@@TKCL yes this heat is very dangerous. You be careful out there and take a break often. You deserve a project in the A/C .🥶

[@AdamDeal-KF0PRI]

oh my nothing worse then smokeing a slip clutch! i was running grain cart for a friends neighbor and that was horrible! i opened the shoot befor i hit the pto and oh boy was it mad! took a few cycles to get it cleared out and running!

[@AdamDeal-KF0PRI]

clutch was mad not the neighbor!

[@TKCL]

Lol I've ner burnt one that bad.

[@AdamDeal-KF0PRI]

@@TKCL oh i didnt burn it to the point it went south to smithereens but it was to the point it worked better then it did!

[@ryanzynda5114]

Thanks for sharing. Love the channel. 🤠

[@madarain]

Question: I have the RC2060 and was wondering if it's safe (or smart) to use the cutter with the curved rear plate removed (as you have it at the end of your excellent video) This seems like it would allow cut grass to more cleanly exit the blade box. This would be an advantage when I'm collecting the cuttings to make compost in large quantities. Thanks

[@TKCL]

It's there for safety reasons, but we removed the chain guards because they were affecting how the material is distributed.

[@hrlee2381]

You have a very attentive assistant.

[@TKCL]

Sure do

[@toddpacheco4748]

Andrew,I saw that you had your supervisor checking out your work 🐶❤😮

[@TKCL]

Always!

[@jeremiahs45]

Makes me want to go sharpen my rotary mower blades now. Did you have the chains on the rear of yours?

[@TKCL]

Yes originally, I think dad removed them because it was dragging thick grass bunches.

[@jeremiahs45]

@@TKCL ah makes sense. I’m glad I left mine on. I tend to find things that like to get thrown around and the chains seem to keep things from flying off

[@TKCL]

That are great for that.

[@chrisavila2073]

Yes

[@5150cash]

Nope 🧀🪤

[@TKCL]

Slacking Chris, Cash got you.

[@5150cash]

@@TKCL it was the cheese 🧀🪤 always works 👍🏽

[@chrisavila2073]

No service at camp

[@TKCL]

Nice! Enjoy your time there.

[@jakebredthauer5100]

I suppose the blades should be balanced so they equal each other. The slide in the center of the power shaft may need maintenance. It needs to be able to slip.

[@5150cash]

Andrew you need to get yourself a 1/2 cordless impact for time like this. They break nuts off like nothing something 🤷🏽‍♂️

[@TKCL]

I've got a 800ftlb torque ait operated one. I've been eyeballing a nice cordless Dewalt 👀

[@5150cash]

@@TKCL I have nothing but rigid cordless tools. And my half inch impact will take off 1500 foot pounds of torque and will tighten up to I believe 800 foot pounds of torque. Works awesome

[@byronholmes2496]

Good day all.

[@TKCL]

Good day

[@rongray4847]

Hi Andrew, enjoyed your video, 👍👍❤️❤️🇨🇦

[@TKCL]

Thank you for watching sir

[@Crystal-Paranormally]

How's the deck coming along Andrew?

[@TKCL]

It's been miserable hot and slow working as a result. I had something else come up that has me traveling and delaying the deck build as well. I must say I'm enjoying being in the AC more than outside right now with these crazy temperatures.

[@thehillbillyhermit7681]

You skipped the blade reinstallation. Since the bolt drops out of the bottom, some might not know the easiest way to reinstall the blades and put the nut back on the top.

[@TKCL]

Very true, I should have recorded that portion. Especially since the bolts have a "keyway" protrusion.

[@mikemiller5139]

Great video

[@TKCL]

Thank you for watching

[@5thGenNativeTexan]

You change enough of those blades and you'll be investing a nice impact wrench very soon. ;) I've had some of those bolts so seized that literally hanging off the large cheater pipe and hitting it with a torch wouldn't break them loose. But a 3/4" cordless impact wrench made short work out of them.

[@TKCL]

I've been eyeballing a good cordless impact.

[@5thGenNativeTexan]

@@TKCL It's not cheap, but the Milwaukee Fuel 3/4" cordless is a beast. My diesel mech turned me on to one.

[@DestinedForConfidence]

But how do you actually get the blades turning?!?! 😭😭😭

[@TKCL]

He sure did lol

[@sharonurschel6753]

Am I first this time?

[@5150cash]

Nope. Not today. Sorry

[@sharonurschel6753]

@@5150cash when I clicked on the video it said there were no comments! Also there were no views yet! How did you manage to sneak in before me??? Hmmmmm

[@TKCL]

Your actually 3rd today 😬

[@Crystal-Paranormally]

@@sharonurschel6753 I think Cash is on some sort of speed dial or something! I've seen where it shows no views or comments too and I don't get in there either so don't feel alone!

[@5150cash]

@@sharonurschel6753 magic 🪄✨

[@jaclynalley809]

is it BUSH hog or BRUSH hog?

[@TKCL]

It's a rotary cutter. Bush hog is a specific brand of rotary cutter.

[@jaclynalley809]

@@TKCL around here people either say I'm gonna bush hog the pasture field or I'm gonna brush hog! I use my Rotary mower to do either one! 😆

[@hilltop7503]

why not just use a zero turn?

[@TKCL]

Florida, 100 degrees, summertime, bugs, 15 acres to mow. I'm using the AC cab tractor when I can. I do use my zero turn every week in certain areas.

[@jefffrancis6824]

👀

[@TKCL]

👀👀👀

[@5150cash]

UNO

[@TKCL]

Got it!

[@skoffco]

The biggest fight with these damn implements is trying to pull the collar back while pushing the driveshaft forward over the spine! What a stupid design, there’s got to be an easier way. In reality it’s a two-man job unless you’re strong as a bear.

[@TKCL]

There's some technique to it. They do make aftermarket pto quick hookups to make the job very easy.

[@darrells1806]

@@TKCL yes I’ve looked into those might be an option on the 2072. It wasn’t an option for the way my Rhino 8 foot bush hog is designed. It has a double shaft.

[@Bluebird-farm]

Gear box doesn’t have a drain plug on bottom either… crazy… gotta suck it out with a pump