The video shows how to replace the reduction gear on Tongsheng TSDZ2B motor easily with special frock.
Пікірлер: 21
@TheAntoine1915 күн бұрын
The 4 screw on the pltor are ridiculously tight
@Shreddykruger Жыл бұрын
Do I have to buy a new pinion bearing if I want to put the brass spur gear in as a replacement? Cheers
@Shreddykruger Жыл бұрын
How do you get the white gear of the pinion, it will not move like the blue version. It does not seem to be a one way clutch bearing
@bitflink Жыл бұрын
This is the B version of the motor , it is different and all in one piece
@snorttroll4379 Жыл бұрын
How is the obe way stuff s8oced?
@Oceanbluemoss Жыл бұрын
But when you buy the white gear it doesn't come with pinion does it ? Only white gear ? So how do your get white gear off
@roninx12Күн бұрын
@@Oceanbluemoss On TSDZ2 is separate and on TSDZ2B the gear is build with the pinion in one piece.
@garth623 ай бұрын
What is the correct grease to use?
@leonelbrunoaraujomendesfro92018 күн бұрын
Silicone
@otzeus Жыл бұрын
Can I buy metal gear and install it to TSDZ2B?
@Oceanbluemoss Жыл бұрын
Only white nylon gear I'm told as brass doesn't fit
@user-jr5ix2wm4e Жыл бұрын
При правильном техническом уходе сопряжение нейлон и сталь работают лучше чем сталь и сталь. Ввиду физических условий и процессов, данное сопряжение остаётся единственно рабочим.
@Oceanbluemoss Жыл бұрын
Why does the vudeo at around 2mins put the white back in the put a round silver plate across top and tighten the 5 screws only to loosen them again ? Then put the motor back in , it makes the instructions very confusing as the things u do in sequence seems not exactly how you would do it , sure you would not tighten acrews to loosen them again ?
@tongsheng1998 Жыл бұрын
The round silver plate is the tool
@dzidmail Жыл бұрын
@@tongsheng1998 You should put there 1mm thermal plate for massively better heat transfer.
@Oceanbluemoss Жыл бұрын
@dzidmail I myself have never experienced over heating issues with this motor and I'm always on level 4
@dzidmail Жыл бұрын
@@Oceanbluemoss And that was probably their rationale, but that is lousy engineering. You don't create air gap around a motor and then seal it with enclosure. Let the heat radiate and you either can use more power or use a smaller lighter motor.
@Crand0m6 ай бұрын
I have the 750w motor stock firmware and my motor burnt out going up a hill. You need the cooling mod or lower power limit (400w)
@lemoldubricoleurbaguettema5075 Жыл бұрын
Nulle ce moteur et ses performances. Sensor toujours dur même en assistance 5, du 250 watts au 750 watts peut de différence. C'est une merde qu'ils essayent de fourguer. Je revend mes trois moteur pour remplacer par autre chose.
Жыл бұрын
OSF le transforme littéralement (google)
@user-jr5ix2wm4e Жыл бұрын
Понятно, первое техническое обслуживание при нулевом пробеге и далее. Мне понравилось крепление силовых проводов важно, их длина от аккумуляторной батареи должна быть как можно короче.