Toyota 4Runner LED Interior Lighting Kit - Install Dome Lights, Doors and Map Lights

[@saramccoy3936]

"It's gonna be hot, so be careful" *internal scream tossing hot bulb on the ground* "just sit that off to the side" 😂

[@mickstash5067]

as soon as I saw this part i scrolled to comments. im dying laughing at this. im pretty sure i heard the bulb shatter on the ground too.

[@jrod96819]

🤣🤣🤣

[@haynemullikin4921]

This is by far the most easily, well explained video available. Great camera work shows exactly how to remove each lens cover without breaking them! Thanks

[@HeadlightRevolution]

Glad it was helpful!

[@RetiredSince2024]

Tweak I did to help get the map lights out without breaking them was to wrap duct tape around each side of the needle nose pliers, sticky side out. It helps grip the light bulb for easier removal! Awesome video!

[@HeadlightRevolution]

Thanks for the tip, glad this video could help you out with that install! Let us know if you need anything else! Have a great day!

[@drrussdc]

Tape helps, I was able to wrap the bulb and pull it out by hand.

[@marcusthompson5249]

Just got a '24 TRD OF Premium! This is the best video I've run across, thank you!

[@HeadlightRevolution]

Glad we could help! 🙌

[@Specz187]

This video helped a lot for my 2015 4runner limited. I replaced all the interior lights knowing where to use the little pry bar tool. The only ones left are the mirror lights.

[@popclutch_100]

I own a 2019 tacoma crew cab. The two small overhead lights towards the windshield. I pressed on the left cover with my finger. My question is can those covers get broken from my finger?

[@johnhopson273]

I used Duct tape to wrap around the map light bulb to pull it out..worked perfectly!

[@Meangod68]

Awesome video, took me a few minutes to replace the lights inside…Need to get the headlights now..

[@729pjp]

I used your technique when it came to the puddle lights, much easier than others.TY.

[@thorfinthorfin3010]

Appreciate the help. The new lights are a must.

[@ianwilliams1680]

Always helps to see a pro do it before you dive in.

[@HeadlightRevolution]

That it does! Thanks for tuning in!

[@brandonthomas4689]

For the map bulbs, mine were in damn tight. It was so easier just to open the sunglasses holder remove 2 screws and pull down that panel. Twist the light retainer and remove the bulb without worrying about busting a bulb

[@HeadlightRevolution]

Yeah, sometimes those bulbs can be tight. Glad to hear you were still able to get it done though!

[@mattb9664]

That's how mine is- I don't want to scratch the reflector with needle nose.

[@joshcarter9110]

This is the best method! So much easier!

[@lovedeepsaini4016]

I actually busted my bulb because it was too damn tight. Your comment was a life saver!!!!! Thank you so freaking much!!!

[@ryanpaulsen7395]

100% easier. Wish I would have started with this technique. Instead I broke a bulb and that was a disaster. He warned me too.

[@tomtoland2168]

Awesome video! On the map lights, I did the same as another poster and removed the 2 screws and dropped the whole assembly. No fuss, and took less than 5 minutes. I also turned off the light switches before trying to remove the bulbs. :)

[@jspur22]

I saw someone use tape to take the lights out and it worked great. Just made a tiny funnel of duct tape and secured it then pulled the light out. Cracked my first light with the pliers lol.

[@HeadlightRevolution]

Either one works!

[@michaellowery4001]

Thanks for your help!!! Just completed installation on my 2022 Toyota 4runner TRD off road premium

[@HeadlightRevolution]

🤘

[@petergunn1701]

Great video! Appreciate the walkthrough and the talk through. Cheers.

[@HeadlightRevolution]

Glad it was helpful!

[@ryanpaulsen7395]

Great instructions except one thing. The map lights. Just unscrew the two bolts. Then unplug the single connection cord and take your time and do it properly

[@MrBerett315]

The door lights pop out from the sides easier and the vanity lights as well. Overall it really helped though

[@HeadlightRevolution]

Thanks for the feedback

[@nottoclever1]

Super helpful video. Thank you!

[@michaeltatham4307]

So I used this video as a reference and on a 2011 4runner the center dome light that you say be careful, I broke the bulb and had glass all over, so the way it worked the best is to pull down the surrounding plastic trim from the rear facing side about 1-1/2" and twist the bulb socket out and pull out the bulb, way easier and less dangerous.

[@HeadlightRevolution]

That a great tip, thank you!

[@bluecruiser2019]

This is a great upgrade. I just bought my wife a 2020 TRD Pro, Would love to change out all of the interior with LED's. Is there a whole kit or do I need to buy everything separately?

[@makmaley5946]

Dang, this is my question too. Was hoping someone would’ve answered you lol.

[@makmaley5946]

kzbin.info/www/bejne/hpvQhHqAZaaknrs Both sets of lights you need are listed in the description

[@HeadlightRevolution]

We do have a full interior kit available on our website!

[@ayawoke9906]

Thank you and greetings from Phoenix!

[@HeadlightRevolution]

Our pleasure!

[@tonybe4726]

What an awesome video it was so helpful thank you very much!!!

[@steveturvey6168]

There are two screws inside the Sun glass holder. Take those out and you can pull down the whole thing and take the bulbs out from the top. So much easier and you won’t break a bulb.

[@HeadlightRevolution]

Good tip!

[@jwb4bb]

Used scotch tape for the front map lights. Tape on the side and then pull them out. Easy!

[@MariaSanchez-lb4kp]

Wrap painters tape around the bulb and pull down. It’s that easy!!

[@HeadlightRevolution]

Not possible for every bulb!

[@bobl997]

Hey folks, any T10 bulbs work (I like Lasfit) and 31mm Festoon. Again I’m a fan of Lasfit products. For the needle nose method, grip near the base and pry out, dont squeeze the bulb.

[@HeadlightRevolution]

That’s a solid install tip. Using needle nose pliers near the base and prying out instead of squeezing the bulb can definitely make removal easier and prevent breakage.

[@bestofthebest4967]

There is two little screw when you open the sunglasses storage next to and it is the most and best way ever to remove your bulb lights

[@HeadlightRevolution]

Thanks for your tip

[@W0nTonSoup]

Very nice explanation and demonstration for removing the plastic covers and bulbs, thanks 👍

[@HeadlightRevolution]

No problem!

[@jspur22]

Dude this is so sick Im going to do this tomorrow.

[@HeadlightRevolution]

🤘

[@thegrayguy]

Great video, helped me out big time 👍🏼

[@HeadlightRevolution]

Glad it helped! Thanks for watching!

[@JosephMullaney]

Awesome presentation; methodical, logical, and precise. I went to your site to buy, but I only see Level 1 or Level 2 as the purchase options. I want to buy exactly what you recommended and installed, how?

[@HeadlightRevolution]

Joseph, here they are: Map light - headlightrevolution.com/gtr-lighting-crystal-lens-diffuser-t10-194-168-led-bulbs/ Dome light - headlightrevolution.com/gtr-lighting-small-style-lightning-series-led-dome-light-board/ Rear hatch - headlightrevolution.com/gtr-lighting-31mm-canbus-festoon-led-bulbs/ Door lights - headlightrevolution.com/2014-2018-toyota-4runner-interior-door-panel-led-lights-upgrade-kit-level-2/ Vanity light - headlightrevolution.com/gtr-lighting-ultra-series-t10-194-168-led-bulbs/ Also, be sure to check out these reverse lights. They will blow you away with the amount of visibility they give you out the back: headlightrevolution.com/2014-2018-toyota-4runner-reverse-lights-led-upgrade-kit-level-2/ Show less

[@m.fernandez8943]

the map light bulb is difficult to get out, tried pliers. tape, gloves to get a grip, didnt succeed .

[@rossagge]

@@m.fernandez8943 If you haven't gotten it yet, get as close as you can to the base of the bulb with a pair of smaller needle nose pliers and almost pry the bulb out instead of pulling. I did it with the size he had but I think a smaller size would work better.

[@crdczo3]

Marial Fernandez im sure you got it out by now but for anyone else reading this, just pop the whole assembly out. There are two screws where the sunglass holder is and then it pops out with a little pressure near the corners by the lights. Once its out just twist the bulb housing and pull it out. You dont even have to unplug the whole assembly from the roof

[@df446]

It floors me the number of Toyota truck owners - "professionals" - that don't know the overhead center console is designed to be removed from the ceiling for bulb replacement. The bulbs come out with a quick quarter turn - from the top. Mr. Toyota designed it that way.

[@HeadlightRevolution]

Right on, thanks for the tip man! We are not Toyota professionals by any means, but we are lighting experts, so any new information we can get on those vehicles is helpful! Thanks for commenting, have a great day!

[@contrerasmarroquin8295]

thank you very much friend you helped me a lot 👍👍

[@HeadlightRevolution]

You are welcome!

[@Weatherby406]

Can’t feel the tips of my fingers anymore but it’s done

[@ChickensForEggs]

How about the glove box light? Can't quite figure out how to replace that one!

[@HeadlightRevolution]

Shoot us an email, we can help! [e-mail]

[@kevinshamoon6653]

I have a 2022 Toyota 4 runner limited. What size leds do I need for the dome and trunk lights? Thanks!

[@yourdailyblockchain]

I see a couple different year ranges on your website. I actually have a brand new 2022 4Runner but I'm guessing Toyota hasn't changed their interior bulb size. Does this kit also fit new 2022 models? Thanks.

[@HeadlightRevolution]

It sure does!

[@rustyryan2474]

Which light would you use to change the front passenger side footwell?

[@HeadlightRevolution]

Shoot us an email at [e-mail]

[@andrewcarbone6192]

Hope you still check this thread -- are there any issues if you have a mix of the standard and LED bulbs in the interior? Just want the LEDs in the puddle door lights and cargo area. Thanks!

[@HeadlightRevolution]

Nope, no issues! (:

[@JohnJones-ff4nu]

Put tape on the overhead lights to pull them instead of using pliers.....

[@Jh0ac]

Exactly what I did.

[@natehawkins2910]

3:33 “we’re installing these 32 mm...” (as bulb says 31mm on it) lol

[@davidrockwell8542]

Thanks very much. This video was extremely helpful!!

[@HeadlightRevolution]

Glad this helped you out! We have tons of installs for that vehicle, so make sure to check them out!

[@ddoghunt3471]

IF You Have Trouble,,, open sunglass case,remove two phillips stews, pull entire panel down with firm grip on both sides.. unplug electrical from roof(easy connection) bulbs twist out replace with new! SAVE TIME AND FRUSTRATION!

[@HeadlightRevolution]

Thanks for the tip, thats what we like to hear about!

[@timurs7398]

Thanks! I almost pulled it out without unscrewing two stews 😂

[@superbagel7781]

lol should’ve did this the first time I shattered one of the bulbs in there😂

[@eevanskiteboards]

Thank you for the great video

[@HeadlightRevolution]

Our pleasure!

[@spirithealershamanism]

THANK YOU. Fabulous video

[@HeadlightRevolution]

You are so welcome!

[@blessedlife93]

You cannot find that pry tool at an automotive store. That’s a snap on product referred to as “gods thumb” and it is worth the money

[@HeadlightRevolution]

Good info!

[@asands]

Awesome video! Always helps to watch someone else do it. Do you know where I can find compatible colored bulbs for my 2020 4Runner?

[@HeadlightRevolution]

Reach out to us, we got you! 218-755-5200 [e-mail]

[@johnrommelt6560]

Any updates to this? I have a 2020 4Runner

[@HeadlightRevolution]

Here is everything we carry for this gen 4runner. www.headlightrevolution.com/japanese_trucks/4runner/4runner_14_21

[@StegoRex99]

would this lighting kit for my 2024 4runner?

[@HeadlightRevolution]

Yes, it will!

[@Brandon_Thomas]

can't find the lightning board anywhere, any help?

[@ninetytwohundred]

Please advice again on the vanitys..whut GTR ultraseries bulbs is it?specific?

[@HeadlightRevolution]

Reaching out to our CS team would be the fastest way to get some help, give us a call or email! 218-755-5200 [e-mail]

[@cristinageston541]

Can you use the lightning boards on all of the lights or only the middle dome light?

[@HeadlightRevolution]

We no longer have these, sorry! Just normal festoon bulbs now!

[@JohnWon-l4n]

Ditch the pliers and use tape to remove hard to reach bulbs. Wear gloves. Turn off at switch and turn on after switching bulbs. Otherwise, great video.

[@HeadlightRevolution]

Good tip!

[@xihearthype]

I can't decide if these lights are tremendous or not

[@HeadlightRevolution]

What do you mean Kevin?

[@MrHeuristics]

So, the gtr lighting board is no longer available. I'm guessing that, without a proper heat sink, it was melting dome covers and an extreme fire hazard?

[@HeadlightRevolution]

It is not available anymore, but not because of any heat issues. That is just a product that we didn't sell enough of to justify keeping it in stock. Let us know if you have any other questions, we are here to help! Have a great day!

[@805Monty]

Helpful thank you 🤙

[@HeadlightRevolution]

Glad it helped

[@leizzai]

Thanks for this! I studied your video the night before installation. Took me about 10 minutes total working time. I used the plastic wedge tool that came with the bulbs, yikes lol. I'll invest in one similar yo the one in your video. Btw, do you know about glovebox LED install?

[@HeadlightRevolution]

It would work the same way, just need to pull the bulb out and pop in the new one!

[@TnFJ62]

Hey, I don’t want too assume but are these interior lights on the latest gen 4Runner compatible for the 4th gen 4Runner?

[@robertwehlau8906]

Actually I think the link you posted has everything correct?

[@JBSchotte]

I did this a couple months ago and everything was good. Now the lights on the rear hatch are flashing and dimming. The bulbs seem to be seated correctly. Any ideas?

[@furiousfragment7082]

Sell your car

[@HeadlightRevolution]

If you bought this from us shoot us an email and we can help you out! [e-mail]

[@furiousfragment7082]

@@HeadlightRevolution Wow 1 month after his comment thanks to me you noticed it.

[@pawelm552]

Hi have you try to change map lights on Highlander 2021?

[@HeadlightRevolution]

We have not tested that in house, but it should be pretty simple for you to just remove that factory bulb, and double check that it is still a halogen in that applicaiton! Let us know if you have any other questions, we are here to help!

[@pawelm552]

@@HeadlightRevolution Hi I already checked possibility to change map lights- this is impossible because there are diodes lights

[@vondutch666]

thanks for the install help! take care

[@HeadlightRevolution]

Glad we could help with your install, let us know if you need anything else!

[@debrajaye129]

What Yorkim festoon bulb will fit a 98 Toyota 4Runner? Would like to change dome, map and back hatch bulbs. "Garage" says the 31mm won't work on the 98.

[@HeadlightRevolution]

My lookup guide does not give me that map light size, but I have confirmed that the dome light and rear hatch light will both be a 31mm festoon LED! If you could pull out that map light, shoot us an email with the images and we will be happy to get you set up with the correct replacement for those! 31mm Festoon LEDs: headlightrevolution.com/gtr-lighting-31mm-canbus-festoon-led-bulbs/

[@protonmail2268]

Needle nose pliers are fine lol. Just go easy :)

[@HeadlightRevolution]

True!

[@EvolveProgress]

Map lights: It's way easier to flip down the glasses compartment and remove 2 screws holding it up and unclip 1 wire harness to access the bulbs. They are in little turn-lockers that can be easily flipped around if you happen to install the lights with the polarity reversed. So much easier that dickin' around with needle nose pliers trying to get a grip a small glass bulb....it would suck to do all that just to find out you put them in backward.

[@HeadlightRevolution]

Good tip!

[@ramonruiz2653]

Where can I find that lightning board don't see it on hr sight or gtr sight either

[@HeadlightRevolution]

We have the link in the description. Here you go. www.headlightrevolution.com/2014-2019-toyota-4runner-full-led-interior-upgrade-kit-white-1418.4RUNNER.INT_2

[@gonzogonz915]

Please do a episode on the GX460

[@HeadlightRevolution]

We’ll see what we can do!

[@fredmolaa]

Please share the link where we can get the bulbs

[@HeadlightRevolution]

The links to the bulbs used are in the description!

[@michaelspencer5290]

I can't get the dome lights out evem with pliers. Any advice?

[@HeadlightRevolution]

Shoot us an email, we'll help! [e-mail]

[@faithnclutheranchurch4252]

Try a small piece of electrical tape rolled with the adhesive side in, open enough to slip over the bulb. Once over the bulb press onto the bulb and pull with slight wiggle. Works every time for me.

[@Bmac2112]

Check this SUPER EASY method out: kzbin.info/www/bejne/qmSko6eQfaykq9k

[@Ahmad-gf6ku]

Will the same lights work for a 2015 4runner limited?

[@Muddson2121]

Yes

[@ashlynswan6874]

Does the kit come with everything shown here on the video?

[@ryuujiryuu9961]

No the lightning board didn’t come with the kit when I bought it apr 2021

[@HeadlightRevolution]

This board was discontinued.

[@androidandtecnologia]

Thanks bro

[@dominiquestephenson195]

I'm guessing that even though my 4runner is an 03, if it uses any of these types of bulbs im good to go? You dont list an interior kit for my dinosaur, can you assemble one? One last question...does the 03 runner (4X4 Sport, V6, halogen reflector HL) require (reccommend) using Canbus bulbs or other power supply tech stuff? Thanks!

[@HeadlightRevolution]

Give us a call, we can get you an interior kit for your 4Runner! :) You won't run into any CANBUS issues. 218-755-5505

[@talontd3727]

Damn that sucks. I checked the website and you don't have anything for a 2012 4runner except for a ditch light bracket.

[@HeadlightRevolution]

We have just not tested options in that vehicle, that doesnt mean that we don't have anything for you! If you email into us with your vehicle information, we would be happy to get you some recommendations!

[@mat1228]

They looked good until I saw the prices, they’re ridiculous.

[@HeadlightRevolution]

Hey there! Sorry our prices weren't what you were expecting. Hopefully you can find something that fits your budget.

[@Bmac2112]

The visual upgrade is worth the cost. Think about that $144 spread over the 5-10 year life of the vehicle, $0.04-$0.08 per day ...

[@tribalb]

Wish will be your best friend when it comes to this

[@djfunknuckle3375]

@6:22 those lights for the vanity are not T10's? mine wouldn't work. 2nd problem, when trying to put them up, i launched the bulb up past the housing. where are the clips on that housing so i can remove the housing to try to fish the bulb out?

[@HeadlightRevolution]

Hey DJ FunkNuckle! Give us a call and we'd be glad to answer these questions! 218-755-5505

[@allancrimii8801]

Try turning the bulbs the opposite direction. The kit i bought seems to be polarized and only works when facing the right direction. Hope this helps

[@ninetytwohundred]

Same issue here..try rotating them around didnt work..swap left to right and vice versa didnt work either,i think the interior kit didnt come with that vanity light in the video HR pls advice

[@dspdrew]

@@ninetytwohundred Yeah, mine didn't come with that bulb either. With all the different bulbs in the kit than were used in this video, I was pretty confused as to what I bought.

[@lignas]

Is this compatible for 5th gen 4runner?

[@HeadlightRevolution]

You are in luck, as the 5th generation 4Runner was what we used in the video! This kit was designed for that vehicle, so they will totally work for you!

[@semajluwensky907]

Any Reason Why These Lights Will Flicker?

[@joeibarra9003]

License plate?😊

[@HeadlightRevolution]

We have two options! - www.headlightrevolution.com/HR-Toyota-4Runner-14-20-XB-LED-License-Plate-Lights?quantity=1 - www.headlightrevolution.com/2014-2019-toyota-4runner-license-plate-led-lights-1418T4RUNNERLED.PLATE_2?quantity=1

[@jimchesnutt7879]

Has anyone done the side mirror puddle lights?

[@HeadlightRevolution]

We have some plug and play models for 10-13 4Runners! www.headlightrevolution.com/HR-4Runner-Sequoia-96-20-XB-LED-Mirror-Puddle-Lights?quantity=1

[@robertwehlau8906]

Hi there. Nice instructions. Do you have a link for a full lighting upgrade for interior for a 21 4Runner trd pro? Thank you

[@medinagames7375]

Thank u it helped a lot 🐐

[@HeadlightRevolution]

Glad to hear that this video helped you out, thanks for watching!

[@Cowslike2moo]

Instead of using pliers to pull out the light. I wrapped duct tape around the bulb and pulled it out.

[@HeadlightRevolution]

That works too!

[@W0nTonSoup]

Dam I should’ve done that because getting those lights out even with pliers was a pain

[@mikehesq007]

Great video! Thanks!!

[@HeadlightRevolution]

You're welcome Mike!

[@tyrk0820]

I would like to purchase exact same automotive flat pry bar. Where can I find one?

[@HeadlightRevolution]

Here you are! This isn't the same kit, but it has tools much like it with many more options as well! Link: www.amazon.com/Removal-Upholstery-Fastener-Automotive-Aircraft/dp/B074N4SS4N/ref=asc_df_B074N4SS4N/?tag=hyprod-20&linkCode=df0&hvadid=198070022856&hvpos=1o2&hvnetw=g&hvrand=15830167909683980832&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9020241&hvtargid=pla-355480490366&psc=1

[@allancrimii8801]

I got a 5 piece set at Advance Auto for $13

[@alpanday69]

How to change footwell bulb?

[@HeadlightRevolution]

Should be very straght forward, we do not have a video on this unfortunately. Sorry about this!

[@HeadlightRevolution]

Shoot us an email if you are having any trouble! [e-mail]

[@alpanday69]

Thank you👍

[@rustyryan2474]

@@alpanday69 did you figure out how to change this bulb?

[@Goofyahh4567]

Will the dome & rear hatch lights linked above fit an 04 SR5? Thanks

[@HeadlightRevolution]

They will fit!

[@Goofyahh4567]

@@HeadlightRevolution perfect thanks

[@verachen8671]

Hi friend, are you interested in installing the power tailgate to 4runner?We would like to cooperate with you.

[@HeadlightRevolution]

No thanks, Vera 🙂

[@JohnWicksPencil14]

Takes about 20 mins, just wrap your needle nose pliers in blue tape to avoid breaking the map lights

[@HeadlightRevolution]

Can use tape too!

[@michaelbennett8218]

I tried the pliers and was afraid of breaking the bulbs. The needle nose pliers kept slipping off the bulb. Also tried wrapping tape around the bulb, didn't work for me. I then used double sided tape on a pair of needle nose pliers. I trimmed the tape making a long slender triangle matching the jaws of the pliers. Bulbs popped right out with no slippage from the pliers and required less pressure insuring I didn't break the bulbs. Secondly, concerning the door puddle lights. It's much easier to disconnect the wire connection then removing the light assembly so you can see it better and work on it much easier. There's a grey plastic cover over the bulb which needs to be removed to access the bulb. I found by inserting a small flat screwdriver in the gap just below the apex of the arch of the cover and applying a little pressure the cover pops right off. After installing the new bulb and replacing the grey cover all you have to do is reconnect the wires before inserting assembly back in the door. Hope these tips help!!

[@andrewhuffman7156]

Turn the light off before taking the bulbs out...

[@VanillaGorilla502]

Thanks

[@HeadlightRevolution]

Not a problem, glad this helped!

[@jacobbell1503]

Glovebox?

[@HeadlightRevolution]

T10/5 typically!

[@djfunknuckle3375]

where can one get that pry tool?

[@HeadlightRevolution]

You can actually get these pry tools are your local parts store or even Walmart!

[@808Stevie]

11 bulbs including the vanity...

[@CathyFerraro-c4f]

You think the factory would install LED lights, they should for the amount of money that you pay for them

[@HeadlightRevolution]

Most OEM Manufactuers offer LED package now, but they aren't cheap!

[@JM-td8qp]

For the vanity bulbs you may want to consider sticking to filament bulbs unless you can find an LED retrofit that has a decent Color Rendering Index (CRI). LED's are great for everything else but if you have a bitchy girlfriend who actually spends time on that vanity she's not going to like a low CRI bulb to apply makeup which deals with proper coloring and shading.

[@andrewevanoff1192]

Don't use pliers to remove the front bulbs!!! You'll brake it. Remove 2 screws behind the glasses compartment with a Phillips screwdriver and remove the whole overhead console. The bulbs are held in a plastic socket. Twist it to remove and replace the bulbs properly and much easier. It literally takes a minute, maybe two. DO NOT USE PLIERS!.

[@HeadlightRevolution]

good tip!

[@Bmac2112]

This method is WAY easier and doesn't require additional disassembly: kzbin.info/www/bejne/qmSko6eQfaykq9k

[@natehawkins2910]

Andrew Evanoff I wrapped friction tape around my pliers tips and never broke any.

[@adamtanksley]

Great video man! Unfortunately I shattered one of my map bulbs when trying to remove with pliers. The first one worked fine. If anyone has any advice for getting it out I would very much appreciate any guidance! ¯\_(ツ)_/¯

[@HeadlightRevolution]

Very tiny needle nose pliers, and a picker if you have one! You should be able to wiggle the T10 base out

[@jasonhoffman9083]

@@HeadlightRevolution I had something different happen. The bulb was really tight. Some how the bulb and the base went back up in the hole. Does the overhead console come off?