Tractor Engine Swap Wiring Kawasaki to Briggs to Kohler

goo.gl/cEXL1Z Click link to get the GS-338 8 inch wire crimpers. Only $8.99 and Free Shipping. In this video, I go over tractor engine wiring for swapping out an engine on a tractor. See how the wiring harness on tractor engines are wired for Briggs, Kawasaki, and Kohler. I also talk about different ways to splice wires. Disclaimer:
Doublewide6 has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’s videos. Use this information at your own risk. Doublewide6 recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6. Please support Doublewide6 by donating to his Patreon Account / doublewide6

[@epasko5713]

Motor swap FYI, ANY of the coils under the flywheel produce AC only, There may be Up to THREE total! (more on that) You did get it right later on the video calling that little three spaded lug device correctly IS a Rectifier as well as a battery charging Regulator, only 1/2 wave with only 2 diodes BTW a Full wave bridge would have 4 diodes and 4 wires, for better amperage and smoother DC (1/2 is just fine for tractor unless your installing a car stereo :)) now, About that third coil, Kohler came up with a Motor/Brake system (Kinda like on your chopsaw or moterized mitre box where when you release the trigger the blade stops almost Instantly) for a few model years ( on the 17 OHV maybe others) two extra wires Put out damn near 90 Volts at full RPM so be careful! If you run into this Just cap them off, great wire splice tutorial, I had my money on your "hook splice" but you sure proved a proper pair of crimpers is the way to go for sure! Thank's keep it up!

[@Dancing_Alone_wRentals]

I like the time you took to patiently go through the steps.

[@aleblanc3547]

Great tutorial on wire splicing! I have a new respect for the crimp-type connector, that's for sure. If you remember, please let us see the new muffler install as well.

[@doublewide6]

A LeBlanc I will let you see the new muffler when I'm mounting it. I'm hoping it does not hit the back guard on the tractor. In the video I had the back guard removed.

[@AKdogs1]

Thanks, was able to swap Kohler for Kawasaki with the wiring help

[@timpope1221]

Excellent info and your explanation of the topics you are covering makes it very easy to follow and understand, thanks for taking the time to make video's ...great work !

[@susanaustin9967]

Great video, thanks, I'm going kawasaki to Briggs pretty soon your video gave me confidence!!!! Have a great day !!!

[@Dennis-cy4wv]

Thanks for posting this. It is exactly what I was looking for.

[@montgomeryward9952]

Really helpful video 👍 thanks again

[@Lovinflyindrones2022]

How did u start making you tube vids ??? U r a natural at it

[@shawnmrfixitlee6478]

Good info.. I prefer solder and shrink tube . I know it is not always possible though !

[@QQTrick1QQ]

You could slide a pick in the connector of the wire you want to change, pressing down on the pin and pull the wire with end out and slide it into the correct one.

[@roboverholt2035]

I dont like them scotch clips . Any wiring I repair I either soder it or but connectors with shrink tube

[@stevanrose7439]

I’m with you those scotch locks suck. They might get you out the door but they will corrode and you will loose connection. Don’t ever use them on a trailer wiring harness. I throw them out and get good connectors. You can thank me later.

[@abetterlife44]

Thank you so much for the detailed video. Could you please tell me where you were able to find the higher output stator in order to work the blades?

[@Lovinflyindrones2022]

Great video

[@2LateIWon]

Great vid. by the way

[@doublewide6]

2LateIWon Thanks, I think it is some really helpful info. for anyone swapping an engine.

[@Mando2593]

Do u have the name of the adpter

[@hammohammbbyblksheep4251]

hey witch wire did you splice into and what dit it go to i see crimps on both

[@paulwillard5924]

Alternator on engine produces AC voltage (usually, modern engines) regulator/rectifier changes AC voltage to DC volts, unless a diode is used instead…. Just to clarify…😵‍💫

[@heffedirte6243]

With the electrical connector, you can depin it and repin it in the correct orientation. And your solder joints are not hot enough. Don't tell people to fix extension cords. Someone stupid might try and burn down a house with people in it

[@charleslarrimore6521]

why not use the. grease filed connect by 3m

[@markpatterson8863]

Hey dw6 will a vertical shafts 18 hp easily swap to a sears gt6000 that had the opposed horizontal briggs? I have my doubts everything seems wrong . Axel steering pto you name it.Have you ever recovered one of these gt from the 90

[@timothycovey5169]

I need some advice on an engine swap. Maybe you could help ?

[@Lovinflyindrones2022]

Do u ever have rats get in your motor. Two times so far rats has put insulation and not sure what else inside my motor on my zero turn gravely

[@michaelbenoit248]

What happened to the Kawasaki?

[@paulfox4134]

can you recommend what briggs and stratton I could use to replace a Kawasaki fr651v that has more horse power then 21.5? thank you

[@RR-qf8rb]

I changed my 19hp kohler motor. it was on a 2007 Troy bilt the block cracked. Kohler courage 19hp sv590-006 the other mower was a 2002 troy bilt with a briggs 17.5 motor. I put the briggs on the mower that had the kohler on the kohler the two wires coming from the stator ran to a voltage regulator.on the briggs it don't have one. do I need to put the voltage regulator on the briggs motor. it keeps draining the battery when off. also each mower don't have a pto Thanks for any Help Ron-513-8053050

[@426superbee4]

SMART MOVE > SCREW KAWASUXME ! Briggs and Kohler both good engines

[@gamo98]

what a botchy job