xTOOL D1 10 Watt Laser Engraver - Awesome Results!

  Рет қаралды 47,442

Tripods Garage

Tripods Garage

Күн бұрын

Пікірлер: 76
@TheGuitarman1968
@TheGuitarman1968 2 жыл бұрын
Really nice review! I have the Makeblock xTool D1 10 watt laser engraver with the optional roller engraving device and 8 leg extensions. I also purchased the Xtool Honeycomb Bed and Comgrow Enclosure, along with the xTool D1. This laser engraver is amazing, and it will engrave and cut (with limitations) a lot of different materials. Makeblock is also releasing a 20 watt laser and power supply upgrade (plug and play) for the Xtool D1 in May of 2022. The xTool D1 laser engraver is easy to assemble and use (with a small learning curve). The proprietary "Laserbox" software is very limited in what it can do, and spending an extra initial $60 (then $30 annually) for the very advanced and useful "Lightburn" software is almost a must. The key to making the xTool D1 work well is setting the tension on all 3 belts correctly and evenly, and also keeping the track rods lubed. Also, the xTool Honeycomb Bed really helps a lot with heat dissipation, so that you don't burn or discolor the material that you are engraving or cutting. A good enclosure (like the Comgrow) with a smoke extraction setup is also very helpful, especially when cutting. The cable management of the xTool D1 could be better, but it is easily remedied with a little creativity. The trick to speeding up engraving times is learning the proper laser speed and intensity to use. Also, setting burn/cut layer priorities , and increasing "whitespace" travel speed in Lightburn really helps a lot to immensely decrease engraving times. Learning to center an engraving on materials also takes a bit of learning, and the red crosshair targeting laser really helps (it is 16mm off of the main blue laser, and the distance can be adjusted for accuracy in Lightburn). However, using the (shift) "fire laser" and "framing" features in Lightburn really help with the centering issue, once you learn to use them. The WiFi works well, but only works with Laserbox for now. However, when using WiFi you still have to physically push the start button on the xTool D1 for safety reasons. I have not used the phone App. option yet, so I cannot speak for how well it works. I highly recommend the xTool D1 if you are getting into laser engraving, and are not ready to shell out the money for an expensive CO2 laser quite yet. However, just remember that this is a very real "laser," and the UV light is very damaging to your eyes (never look directly at the laser without good eye protection). I highly recommend ditching the included (green) safety glasses and purchasing some professional (amber) laser glasses that are certified to block laser light in the 455nm range. Afterall, you only get one pair of eyes in your lifetime. Also, never burn plastics like PVC, as they will produce deadly Chlorine Gas when heated. Even regular wood smoke can be toxic and irritating, depending on the species of wood. Especially exotic hardwoods like Purpleheart. If anyone has any questions regarding the xTool D1 just let me know, as I have quite a bit of experience with it now, as well as the Lightburn software. I am always willing to help fellow laser users.🙂 PS. The only reason I can think of as to why they call that metal rod an "optical shaft" is that it really hurts if you poke yourself in the eye with it. 🤣
@Mando5
@Mando5 2 жыл бұрын
I appreciate you pausing the video while showing the different parts! thanks
@Adamantus
@Adamantus Жыл бұрын
Thank you for a complete, understandable overview of the Laser Engraver. Nicely organized and presented.
@cyclepathsgravelclub
@cyclepathsgravelclub Жыл бұрын
Will the 5watt laser engrave and Cut wood and such materials
@antonioponzio309
@antonioponzio309 Жыл бұрын
Hi, this laser engrave aluminium? If yes, is this mark dark black?
@TripodsGarage
@TripodsGarage Жыл бұрын
Hello, unfortunately it "will not" engrave aluminum. None of these 455nm laser will engrave metal. You will need to get a 1064nm laser to engrave aluminum.
@christalpeters
@christalpeters Жыл бұрын
Thank you for a detailed video on this product
@7311951George
@7311951George Жыл бұрын
I can’t find where I can buy the 3D print legs holder for the XTool legs
@chrislmink
@chrislmink 2 жыл бұрын
I have been looking at this laser for a bit now and I must say I will probably go with this one. Light burn basic might be their way of getting people to buy the better software. Thanks for the review
@TripodsGarage
@TripodsGarage 2 жыл бұрын
It is one fantastic laser! Yeah the software supplied is lack luster and needs some work. Thanks for watching!
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Easter sale, get 5% Off using coupon code TripodsGarageEaster - from "April 6th to May 6th" www.xtool.com/?ref=if7I0mUlth-h&
@MrJNiece
@MrJNiece 2 жыл бұрын
Thank you for the review! I just purchased mine and I’m still learning. Thanks for including the spoil board dimensions! The XTool honeycomb board comes in inches (but shows in mm on the website) and I’m still trying to figure out which I should stick with (in/mm). Wish I paid better attention in grammar school when they wanted us all to learn the metric system. Would have been helpful if the US converted! I’m still trying to figure out how to match the grid in lightburn to the spoil board. Any suggestions? Again, great review.
@duster.
@duster. 2 жыл бұрын
John, I will be 69 in November and use metric all the time, multiples of 10, nothing easier
@AndrewAHayes
@AndrewAHayes 2 жыл бұрын
I have a K40 but its not big enough for some of the projects I have planned so I have been thinking about making a tool change for my MPCNC but cant find any laser half as powerful as the Co2 laser in my K40, I cant easily put the guts of the K40 on the MPCNC as there are mirrors involved and I dont want unprotected laser beams in my shop, I suppose I could enclose the MPCNC which I have also been thinking about, but then I would need open access to the machine for servicing and the changing of the tool head from time to time. It wouldn't be so bad if I could get my hands on a larger diode laser system but as of yet they are still relatively small
@kwkstar
@kwkstar 2 жыл бұрын
I ordered one with the upgraded roller and your discount got me $50.00 off, Thanks! All of the parts will not be here until the end of the month though!
@TripodsGarage
@TripodsGarage 2 жыл бұрын
That is awesome! Glad you were able to save some money 💰!I will be getting the RA2 rotary also. I love using mine, hope you get as much enjoyment out of it as I do 👍
@kwkstar
@kwkstar 2 жыл бұрын
@@TripodsGarage I just hit abunch of garage sales getting cups painted ss and porcelain. And all sorts of metal things for the rotary fun jig
@LisaHarsh
@LisaHarsh 2 жыл бұрын
I love your reviews. Thorough and honest.
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Thanks! I totally appreciate it! Thanks for watching and commenting
@tanyad6179
@tanyad6179 Жыл бұрын
Will this machine engrave a hockey puck?
@learnmakerepeat7140
@learnmakerepeat7140 2 жыл бұрын
Thanks for not disappointing, John. 👏👏
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Thanks bud! Thanks for watching and commenting!
@duster.
@duster. 2 жыл бұрын
Brilliant review, thank you. Mine arrives tomorrow
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Thanks! Hope you enjoy the D1!
@cassianoeberhardt
@cassianoeberhardt 8 ай бұрын
Does it cut paper like for wedding invitations?
@TripodsGarage
@TripodsGarage 8 ай бұрын
It can, suggest start with really low power. Just because it can flare up fast.
@petercasper224
@petercasper224 2 жыл бұрын
Fantastic and honest review! Really enjoyed watching.
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Thanks much appreciated!
@elizabethbatchelor3068
@elizabethbatchelor3068 2 жыл бұрын
What is the honeycomb mat you used? Where can I get one?
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Link is in the description below 👍
@UnitTx1953
@UnitTx1953 2 жыл бұрын
Where did you graphic for the cutting board from?
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Found it on Etsy
@michaeld954
@michaeld954 2 жыл бұрын
Can you do mirrors
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Yes it can
@astedino
@astedino 2 жыл бұрын
Hi, are you using the lightburn or the program that follows with xtool?
@TripodsGarage
@TripodsGarage 2 жыл бұрын
I used LightBurn for most of the engravings. I used the xTool Creative Space for the tumbler and the large bamboo cutting board.
@jeniferwaelty2844
@jeniferwaelty2844 2 жыл бұрын
How thick is your MDF board and what is the size of it?
@TripodsGarage
@TripodsGarage 2 жыл бұрын
The MDF is 26in sq by 1/2. Thanks for watching and commenting 👍
@ravynsage
@ravynsage 2 жыл бұрын
@@TripodsGarage Thanks for the video. So where did you obtain the MDF? Was it custom cut?
@jasonwooca1
@jasonwooca1 2 жыл бұрын
what is the actual laser working area size LxWxH? 🙏
@TripodsGarage
@TripodsGarage 2 жыл бұрын
The actual size is approximately 600x590x150mm
@CncObsession
@CncObsession 2 жыл бұрын
Maybe a small drag chain for the cables. Cheap on Amazon.
@ryansmith5115
@ryansmith5115 2 жыл бұрын
Great video man, very informative. Looking at purchasing one currently. Would the 10W version be powerful enough to cut through say 6mm plywood and 6mm acrylic?
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Greetings! Thanks for watching and commenting! It is tough to say if it will cut through 6mm of plywood on one pass. The reason, not all plywood is the same, nor very consistent. My answer would be, maybe in two passes, since it is an engineered wood. If you are looking to cut clear acrylic, it cannot. It can cut black acrylic at 5mm with one pass at 1% speed 100% power. Otherwise it might need another pass. Remember, the further the laser is from optimal focal length, the weaker it becomes. Let me know if you have any further questions.
@omare777
@omare777 2 жыл бұрын
Your code gave me a 40 bucks discount, thank you for that! and for the review! One question (of many), what where the settings for the bamboo?
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Awesome! Everyone likes saving money! The bamboo was engrave at 65% Power and 100mm/s. Like any material, I would suggest testing first when you can. Thanks for watching and commenting!
@peteryuen5526
@peteryuen5526 2 жыл бұрын
Can it cut clear acrylic?
@TripodsGarage
@TripodsGarage 2 жыл бұрын
This can cut black acrylic. Unfortunately it cannot cut clear acrylic. You will want a CO2 laser for that.
@lindacalderon6417
@lindacalderon6417 2 жыл бұрын
What product did you put on the glass?
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Tempera Paint - www.amazon.com/gp/product/B000F8R276/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1
@lindacalderon6417
@lindacalderon6417 2 жыл бұрын
@@TripodsGarage Thank you!
@TheLouisianaHobbyGuy
@TheLouisianaHobbyGuy 2 жыл бұрын
I have a honeycomb build mat or thing too! 🤪 Good review as usual!
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Yeah, this may things 😂. My dog Oreo kept on coming in and out of the garage, and must hav re-recorded that about a dozen times due to background noise. I was to that point it will remain a laser mat thing 😂. Thanks bud 👍
@mgpmbass3616
@mgpmbass3616 2 жыл бұрын
I have one of those honeycomb build mat things being sent to me.
@johnkemas7344
@johnkemas7344 2 жыл бұрын
xTool has replaced the basic laser box software with their XCS Creativer software, but nothing beats Lightburn!
@Firstleaker
@Firstleaker 2 жыл бұрын
Taco Tuesday 😂😂! Now that is an awesome review 👍. I really like the build quality, and you got some amazing results. Another great review Tripod!
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Yes! Taco Tuesday! Of course there will be food that is engraved!
@justinhamrick1099
@justinhamrick1099 2 жыл бұрын
Awesome work! 👊. Idk what to say I bout a xtool
@woodwaker1
@woodwaker1 2 жыл бұрын
Cleanest burnt tacos ever - what food will be next? I'm sure Bear loves all of his new tags.
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Yes! Bear loved the taco shells! He kept on bumping the tripod knowing it was for him 😂. Also Bear does love the new laser engraved tags!
@charmycharmQA
@charmycharmQA 2 жыл бұрын
Can XTool D1 10W engrave on stainless steel ? I mean engrave not only print
@TripodsGarage
@TripodsGarage 2 жыл бұрын
It will mark stainless steel. I could feel the ever so slight etch in the container I showed with the Ford Tough logo. If you want to engrave and etch stainless steel, and other metals, you should go with a fiber laser.
@rubendgutierrez2590
@rubendgutierrez2590 2 жыл бұрын
Sorry he solicitado en varias oportunidades conocer más de la máquina /y/o distribuidores representantes ( ventas ) catálogo y mantenimiento de la máquina y valor No he recibido noticias Gracias Rubend Miami Fl
@mgpmbass3616
@mgpmbass3616 2 жыл бұрын
Another awesome review! However, I'm surprised that no Peeps were harmed in this review. Speaking of Peeps, a Peep cook temp cutting board would be neat.
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Yeah, the Peeps didn't want to come back after the last laser engraving review 😅! A Peeps cook temp cutting board, now that is an idea! Thanks for watching and commenting!
@sanjeewajayarathna7037
@sanjeewajayarathna7037 2 жыл бұрын
#WeAreWithGota
@vefaylmaz1524
@vefaylmaz1524 Жыл бұрын
176 min for cutting board ? so slow
@TripodsGarage
@TripodsGarage Жыл бұрын
Yeah I was surprised as well
@PerfectChord
@PerfectChord Жыл бұрын
That's 10,560 seconds. That is slow.
@bruceyoung1343
@bruceyoung1343 2 жыл бұрын
$660. I don’t think so
@TripodsGarage
@TripodsGarage 2 жыл бұрын
Plenty of choices out there.
@LeoVasquez
@LeoVasquez 7 ай бұрын
This took way too long to unbox and quit using big words. Just unbox it.
@TripodsGarage
@TripodsGarage 7 ай бұрын
Yeah, imagine how long it took to assemble without editing! I know the assembly and use of big words is not nearly as exciting as racquetball, but I try.
xTool D1 pro 10w laser, watch this before you buy
23:04
Anthony Scolaro
Рет қаралды 44 М.
Will a Diode Laser Engrave Steel? | xTool D1 Testing
32:49
Clough42
Рет қаралды 215 М.
Try this prank with your friends 😂 @karina-kola
00:18
Andrey Grechka
Рет қаралды 9 МЛН
Сестра обхитрила!
00:17
Victoria Portfolio
Рет қаралды 958 М.
黑天使只对C罗有感觉#short #angel #clown
00:39
Super Beauty team
Рет қаралды 36 МЛН
How It's Made: The Master Forge
36:16
CharaChorder
Рет қаралды 1,7 М.
Best Beginner Project-  Xtool D1 Pro
14:37
The Laser Channel
Рет қаралды 10 М.
This is like printing money with the xTool P2
18:24
New Yorkshire Workshop
Рет қаралды 254 М.
How to Etch Glass with the xTool D1 10 watt Diode Laser
13:56
Build Dad Build
Рет қаралды 183 М.
Watch This video Before You Buy the xTool D1 Pro!!!!!
17:15
Ken Moon
Рет қаралды 81 М.
The ULTIMATE xTool D1 Pro Review + Deep Dive
35:53
Laser Everything
Рет қаралды 36 М.
Best Laser for Beginners - xTool D1 10w
18:20
wittworks
Рет қаралды 39 М.
I was wrong about the xTool D1...
7:13
Make or Break Shop
Рет қаралды 36 М.
Try this prank with your friends 😂 @karina-kola
00:18
Andrey Grechka
Рет қаралды 9 МЛН