Troubleshooting the La-z-boy 3-Position Footrest Feature

[@reclinerrepairguy4155]

I tried to order a set of Pivot Pins this month and was able to get them! Sometimes a rep will give you bad information regarding part availability -- like I did in this video! And other times parts may be temporarily unavailable, but become available again later on.

[@osooro13]

@reclinerrepairguy any recommendations for a recliner, that no longer stays locked in the reclined position? It rocks when the footrest is extended. This occurred after my 3 year old thought it a good idea to jump off the extended footrest.

[@lindamjohnson4989]

If you could please tell me how I can adjust my legs were they won't raise I would appreciate it please please send me a message thank you

[@c.danjou.1696]

I'm 74 y.o., and I still learn from experienced youngsters. Thank you for your demo. I made my 3 positions footrest repair in less than 10 min, while I tought it was over for good. Bravo to you.

[@reclinerrepairguy4155]

@c.danjou.1696 - Good job!

[@popsravendish8617]

Thank you so much for this video! My wife's 12-year-old recliner had started locking in place not allowing her to open or close the recliner. She NEVER used the 3 position aspect of the chair. I simply removed the "pins and springs", removed the connecting arm and now her recliner works smoothly. Perfect. Thank you again.

[@reclinerrepairguy4155]

@pops ravendish - You're welcome!

[@jrimpau]

Thank you for this video! I have a nice leather La-Z-Boy from 2001. The footrest has been sticking off and on and last night became completely stuck in the up position. Using your video as a guide, I completely removed the 3-position lever. I also appreciate the warning about having it all the way open or closed, to safeguard one's hands. I will not need to rebuild, as I only need completely up or completely down. My chair now works like a charm! And it only took about ten minutes and no repairman's bill to pay! (By the way, I am a 68-year-old woman. I'm quite mechanically inclined and relatively strong, and I like to fix things if I'm able.)

[@reclinerrepairguy4155]

@Joy Rimpau - Congrats! Disconnecting the older 3-position mechanisms is a prime example of knowing a few simple steps, rather than being highly-skilled or trained in order to perform the required fix. Good job!

[@jrchefcentral]

Thank yo sooooo much for your videos. I was able to repair my 80 year old Mom's (very old) but much loved recliner.

[@reclinerrepairguy4155]

@jrchefcentral - You're welcome -- good job!

[@dannihardy7874]

You are awesome sir. 1 of the springs attached to the bullet pin broke, just like you showed. I was able to get a customer service parts department number from La-Z-Boy, texted pictures of bullet pins and springs to lady, she ordered my springs, they arrive today. She even knew what type repair video to look for on YT, and your video was exactly what I needed to see what position I needed the 3 position lock needed to be in when I start.

[@XanderJudd24]

Thanks for these videos. My Lazyboy recliner is 22 years old. The reclining gear finally stripped out. I didn’t want to trash the chair. I followed your video to fix it, ordering parts from Amazon. Then I realized the 3-position footrest hasn’t worked for years, so when this video, I fixed it. My parts look a bit different but you gave me enough to fix it. The little springs were broken but I still had the pins. I found a long spring at Ace Hardware with the correct circumference. I cut two springs from this new one and voila! It worked. Thank you. You saved me $1,000 for a new big chair.

[@reclinerrepairguy4155]

@XanderJudd24 - You're welcome -- good job!

[@tjhunter56]

Mr. Recliner Repair Guy, Thankyou for this information!!! It is 2024 and your video is continuing to help people. Thank you!!!

[@reclinerrepairguy4155]

@tjhunter56 - You're welcome!

[@marymcivor4902]

Thank you so much! I have a 1991 Lazy Boy recliner that I bought new and have never had a problem with until the other day when the footrest got stuck in the up position. Thanks to your clear instructions and excellent video footage, I, a 61-year-old woman, was able to pull off the back, flip it over, and remove the small pins and springs around the 3-point ratchet, and now it works perfectly! I never realized that I don’t use the footrest positions any way. I adjust using the back ratchet mechanism. I’m back in my “Lazy Girl” again!

[@reclinerrepairguy4155]

@Mary Mclvor - Congrats!

[@kimkelly2442]

Thank you so much for your videos. I bought a 50 year old Naugahyde petite lazy boy recliner rocker at a yard sale in perfect condition. I didn’t realize the foot rest had three positions! And now I know that if anything goes wrong I can come back to your KZbin channel to figure out what’s wrong!

[@BFTBGSFTST]

Thanks! It was the bullet pin getting stuck was my problem. I have my grandparents lazyboy, was my grandads chair he used before he died, and then my grandma used it until she died. It's mine now and it means a lot to me.

[@reclinerrepairguy4155]

@BFTBGSFTST - You're welcome -- good job!

[@joannethibault2918]

Thank you recliner repair guy. My foot rest wouldn't close and your video gave me the confidence to look at the mechanism. The notch wheel just needed to be clicked back into its proper place - somehow it got out of kilter.

[@wperry1]

THANK YOU!!! I had no idea that piece that was getting stuck in the middle wasn’t necessary to move the foot rest up and down. My chair is quieter, moves easier, and doesn’t get stuck anymore!

[@reclinerrepairguy4155]

@William Perry - You're welcome!

[@danceroomballer]

The bolt that connects my extension scissor to my rear arm has sheared off. I have no idea if I can get a replacement, but I'm so grateful you have helped me learn the correct terms to use as I begin my search. Please keep up the good work!

[@reclinerrepairguy4155]

@Dave Killion -- Those shoulder bolts are no longer available. They're been replaced with plastic Legrest Swing Bushings that are fastened to the Leg Extensions using Truss Head Screws. Learn more by watching the video 'Installing Legrest Swing Bushings' at the ReclinerRepairGuy.com website. And by the way, check to make sure that the round opening in the Rear Swings -- that holds these bushings -- is not elongated from wear. If it's no longer perfectly round, the Rear Swings should be replaced as well. That would be covered in the 'Drive Rod' 3-part video series, also on the website.

[@danceroomballer]

Thanks for the tips, @@reclinerrepairguy4155 . These are not shoulder bolts. I have found La-Z-Boy compatible metal mechanism bolts that look like they will work. recliner-handles.com/replacement-metal-mechanism-bolt-la-z-boy-compatible/

[@imagonna8330]

Thank you! Just took it off completely. Tired of getting stuck in the chair. Works great now and never used the middle positions anyway. Found one pin had some very deep grooves in it once it was out. Thanks again for taking the time to make these videos. So helpful - even I could do it!

[@reclinerrepairguy4155]

Imagonna - You're welcome!

[@EmiRee14]

Thank you! Disconnecting the 3-position lever was all I needed to do to give this old chair a new life. Thank you!

[@reclinerrepairguy4155]

@EmiRee14 - You're welcome!

[@eichelman]

I used WD40 on the pins and got mine working, from your video! My pins would get stuck from position 2 to 3, and it wouldnt close, but now all seems well. This is the best home repair video I have seen, and I have seen a lot!

[@tinahatfield8077]

This video has helped me greatly as my foot rest kept getting stuck in the half way position with me in the chair or out of the chair. I followed your instructions and removed the mechanism with the teeth & the bar. Now, the chair works great. Thank you so very much! Awesome and helpful video!

[@reclinerrepairguy4155]

Tina Hatfield - You're welcome -- I'm glad the video helped you!

[@lynndolphin1473]

Hi Recliner Repair Guy! Thank you sooooo much for the excellent video. Very helpful for the 3 position repair. Got the bullet pins and springs on Ebay for $15. Not sure where the spacer goes but we fixed a 12 year old chair pretty easily.

[@reclinerrepairguy4155]

@Lynn Dolphin - Good job! The spacer that fits on the Drive Rod -- if that's the one you're referring to -- goes between the 2 Lock Plates (gear-like looking parts).

[@johnjordan3126]

Hey thanks! I was just able to repair my old L'Boy that wouldn't close (I disabled the latch). No Patreon hit so I hopped on your website. I've enjoyed watching your videos. Cheers!

[@steveneil3607]

I was just looking for the method to re-attach the pins, springs, and bar to my favorite chair. Thanks for the video!

[@reclinerrepairguy4155]

@Steve Neil - You're welcome!

[@gregerway8369]

This was an awesome video. Showed me how to remove the 3 position locking bar and once removed the chair can now work properly. Thanks for the quick tip.

[@reclinerrepairguy4155]

@gregerway8369 - You're welcome!

[@Go-go_Godzilla]

This was ab-so-lutely the right video for me, thank you very much! Used the information to DIY a spring repair after it snapped. Thanks from Texas, Recliner Repair Guy, you rock!🤘

[@reclinerrepairguy4155]

@Go-go_Godzilla - You're welcome!

[@Asvaldrz]

Thank you for helping me repair my chair from across the world. I really appreciate it.

[@reclinerrepairguy4155]

@Asvaldrz - You're welcome!

[@nelsonbrunanski596]

Thank you so much Recliner Repair Guy. I've been ill and my chair was stuck. When I got out of the hospital I came home to my stuck chair. You solved it perfectly in no time. Much gratitude for your generous contribution. I like your friendly, easy-going style as well.

[@reclinerrepairguy4155]

Nelson Brunanski - You're welcome -- I'm glad the info helped you out!

[@jmlinne]

You are an excellent instructor. Thanks for this

[@reclinerrepairguy4155]

@jmlinne - You're welcome!

[@NeverMetTheGuy]

Thanks for the video, my good man. The pivot pins look a lot like one of the pins within the trigger housing of the Remington 870, although they're going to be wide. I'm gonna need to dig around for them to see if that would be a viable option even though they wouldn't be factory. Also, the entire time you're saying "upgrade" to the "modern" PLASTIC parts by buying extra crap, my brain was screaming "Cut it out of metal!" I may still be young, but I've learned that plastic is almost never an upgrade. Merry Christmas, brother.

[@reclinerrepairguy4155]

@NeverMetTheGuy - I just placed a La-z-boy part order that included Pivot Pins. I want to see if they might be available again. Check with your local La-z-boy dealer to see if they may have some left in stock. "Upgrade" was a poor choice of words, "convert" would have been better. I have to say though, that I do recommend the conversion for those who use the 3-position feature heavily. The plastic clips are easier to swap out, typically last a long time and are cheaper to replace.

[@reclinerrepairguy4155]

@NeverMetTheGuy - I was able to get the Pivot Pins I ordered. If you've not tried to order them yet, give it a shot!

[@chrisnaidoo4596]

Thanks for sharing your intimate repair knowledge in a very meaningful & easy to understand manner :)

[@reclinerrepairguy4155]

@CHRIS NAIDOO - You're welcome!

[@stephenrasdahl1578]

Thank you for your videos! Great information. Take multiple pictures of the mechanism of your chair. That's saved me more than once. 😅

[@reclinerrepairguy4155]

@stephenrasdahl1578 - You're welcome -- great tip!

[@connorcmedia]

Bro. Thank you so much. I had to fix the pin real quick. I totally appreciate you. My grandma’s chair is so old that you can’t even put up the footrest.

[@reclinerrepairguy4155]

@Connor Cochran - You're welcome!

[@connorcmedia]

@@reclinerrepairguy4155 yessir reply from the man himself!!!

[@terryknights1]

Thanks for the clear video, I could see the parts I needed to fix as one of them had fallen off

[@reclinerrepairguy4155]

@Terry Knights - You're welcome!

[@patriciamattson4645]

That suggestion worked great. Really appreciate you

[@brenthebert472]

Thanks for the video. My recliner was operating well until the last few months. The first 2 footrest positions lock as they should, nut fails to lock in the 3rd, straight out position. I can literally push it back down.

[@reclinerrepairguy4155]

@Brent Hebert - I've seen some older La-z-boy's develop this issue as they age. It's not a problem unless the footrest is closing when you don't want it to. If that's the case, it can be due to a few different causes. If you can't identify the problem, hire a repair tech to help you out.

[@rickgriggs1365]

Thanks for the video! Found pins & springs on eBay, so I bought extras. Would have been nice to see re-installing the pins/springs for any tips - that was a challenge.

[@DudleytheBostonTerrier]

Thank you for these videos!

[@reclinerrepairguy4155]

@DudleytheBostonTerrier - You're welcome!

[@brianking6750]

Thank you! I was able to fix my recliner for the cost of a spring. Easy fix.

[@reclinerrepairguy4155]

@Brian King - You're welcome. Easy fixes are the best kind!

[@CW2TRH]

Thanks. You just saved me $1200. Wife had ordered two replacement chairs. :-)

[@reclinerrepairguy4155]

@CW2TRH - You're welcome!

[@Gwerd]

Thanks, I fixed my chair with your tutelage!

[@reclinerrepairguy4155]

@Drew Gauley - You're welcome!

[@danielnemschick3988]

Your videos have been very helpful. I am a furniture repair technician. Why don’t you have any video of the installation of the upgraded metal drive toggle in place of the plastic one ? I do this repair at least once a week. ?

[@reclinerrepairguy4155]

@danielnemschick3988 - Coming soon!

[@lilgogo527]

Thank you so much! I was completely lost on how to fix my damn chair until I found this video lol

[@reclinerrepairguy4155]

@Lil GoGo - You're welcome!

[@lorenzocole8166]

TYVM ! I just got my recliner to close.

[@reclinerrepairguy4155]

@Lorenzo Cole - You're welcome!

[@ronaldkruml]

Thank you for helping to repair my chair!!

[@reclinerrepairguy4155]

@Ronald Kruml - You're welcome!

[@deejohnson5163]

My manual recliner foot rest is being used and out of no where it just drops a few inches. Sometimes it happens immediately and sometimes it's an hour later. It recently dropped the foot rest all the way to the floor. Any ideas, any videos to follow ??? Thanks.

[@theoriginalplasticwrap]

I have an older style 2004 model with the pins. My u/c bracket (spring hook) broke on it and no nearby dealers sell it anymore. Seems like finding parts for older model chairs is impossible.

[@reclinerrepairguy4155]

@theoriginalplasticwrap - The parts you need for your 3-position footrest setup should still be available. Contact La-z-boy through their contact (email) form on their website to find out.

[@Scoobydoonut]

I have an old lazy boy rocker recliner, the wire that pulls the foot rest up and down has broken several times, that I fixed with some wire I bought from fleet farm, but this time after I fixed it, I have been having this problem of it only going to one position, which I'll look at to see if I can see what you are showing here, even though mine does look quite a bit different, but the problem that's really bothering me is that when it's reclined it seems to not lock in place. So when I'm laying back the chair still rocks back wards. What could cause that?

[@reclinerrepairguy4155]

@Scoobydoonut - It sounds like your Ratcheting Recline parts may be worn and need replaced. See this video ---> kzbin.info/www/bejne/mmmlnGWgacmWY80

[@nancynabholz1178]

We have a La-z-boy reclining sectional sofa. We have trouble closing the footrest on one end, while sitting on it. The footrest hits something and won't close. If you get up, then push the footrest with your foot, it will close fine. We have turned it over and can't figure out what's going on with it. We can't see anything that looks out of place or broken. Thanks for any help that you can offer.

[@reclinerrepairguy4155]

@Nancy Nabholz - That could be due to a few different things: The footrest may be striking the floor or the frame of the sectional. Or, the Leg Extension scissors may be striking the front floor rail, or the mechanism may be bent / damaged. I recommend having an experienced La-z-boy repair tech pinpoint the cause.

[@nancynabholz1178]

@@reclinerrepairguy4155 Thank you!

[@lonaockenden2643]

We have a 1995 lazy boy that the footrest sticks in the middle position. Would you suggest we try to replace the springs and bullet pins if we can find them. Everything else looks smooth, tight, and straight. Thank you

[@reclinerrepairguy4155]

@Lona Ockenden - The Pivot Pins don't need to be replaced unless they have obvious gouges on them (surfaces are no longer smooth). The Extension Springs can be replaced, but if they're not broken and the end "hooks" aren't stretched, they will still work. (Order a spare set if yours are still good.) The Lock Plate(s) and 3-Position Lever are the parts that typically need to be replaced due to wear or the Lock Plate getting caught inside the 3-Position Lever during operation. It's been a while, but the last time I tried to order Pivot Pins, I was able to get them.

[@lonaockenden2643]

@@reclinerrepairguy4155 Thank you! We will try to get a new Lock Plate and 3-position Lever

[@jojeeplvr]

Thank you for this post, it worked!!

[@reclinerrepairguy4155]

@jojeeplvr - You're welcome - good job!

[@connersnow298]

Awesome vid and edits and filming and chair

[@mt357mag]

Hi. I have the same type of mechanism as the recliner you are working on in this video...metal parts & bullet pins except I have 2 metal position levers that connect together, one large & one small & I also have a large coil spring.. I'm having trouble figuring out how to install the position levers and where do I connect the coil spring & does the coil spring face up towards the cusion? Thanks.

[@reclinerrepairguy4155]

@Marty Tobias - I don't have a photo to send you at the moment. Contact me through my email address -- [e-mail] -- and I'll try to send a photo when I'm back in the shop.

[@mt357mag]

@@reclinerrepairguy4155 Thank You Sir.

[@tearjerkMASS]

What is the name of the large semi-circular silver part next to the scissors mechanisms on each underside of the chair? The circular parts rotate when the recliner lever is engaged or disengages. One of the "circular parts" is inoperable because the rivet holding the circular part to its attachment on the recliner operating shaft sheared off completely. How do I stretch the spring to align the circular part with the stationary "ear attachment" on the recliner lever shaft? I can't afford to replace this chair so I hope you can help me.

[@reclinerrepairguy4155]

@tearjerkMASS - The "C"-shaped part is the Toggle Subassembly. The purpose of this part is to hold the tension springs that assist the mechanism in opening & closing. Newer chairs have 1 Toggle, while older models can have 2. With one failed Toggle, you should still be able to open & close the recliner. But you may notice there's less of an assist from the springs. If that's the case, you don't need to repair the failed Toggle. If you decide to repair/replace the bad part, get an experienced repair tech to quote the repair.

[@hlramos24]

I have a Merax reclining massage chair I got it two weeks ago and it's already giving me the footrest is stuck open the backrest is laying down I can't lock it back down it's a manual footrestplease if you can advise me on how to fix it I rather not have to go and call for them to come and fix it if it's something simple

[@EdCatlett]

Thanks so much for this. The recliner I have is one my parents used to have and has the old metal 3 way. I was able to get that disconnected so now the footrest does go all the way down and will lock up. A side effect is that now the ratcheting for the back doesn't work anymore. I don't believe I will be able to get replacement parts that will work. I suspect the answer is no but is there any way to get the back to ratchet as well? I was thinking maybe some way to plug the gaps in the 3 way and re-connect it. Thanks in advance!

[@reclinerrepairguy4155]

@EdCatlett - The Ratcheting Recline tips (pitches) the entire chair back. It's separate from the 3-Position Footrest function. The Back tilt is yet another separate function, independent of the other two. (See the 3-Position Footrest & Back Tilt Tension videos to learn more.) Disconnecting the 3-Position function will not stop the Ratcheting Recline (or back tilt) from working, if it was working properly to begin with. However, you may have to use the chair a bit differently to engage the ratcheting feature. For example, if the chair is slumping forward when the footrest is fully extended, you'll need to move your weight back in the chair to engage the Ratcheting Recline. 2 ways to do that: #1 If you have long legs, move 1 leg off the extended footrest & onto the floor & push back to engage the ratchet. Or push back against the arms. Or, #2 Do not sit or lean forward when opening the footrest. But rather throw your shoulders back a bit when opening the footrest to engage the ratcheting recline. If none of these suggestions help, find an experienced repair tech to troubleshoot the problem.

[@donriley9053]

Okay, I took the swivel base off, and was able to remove the springs and pins, and the arm. Put the chair back together, and the footrest goes up, but won't lock in place. What should I be looking at?

[@reclinerrepairguy4155]

@donriley9053 - If the footrest is closing on its own -- not staying open -- you need to inspect the Leg Extenders (scissors), Toggle tension spring & other parts along the Drive Rod. You're looking for bent, broken or damaged parts that are preventing the footrest from locking out into the full-open position. However, if the footrest is staying open, but the chair itself is dipping down in the front, that's likely due to worn Ratcheting Recline parts. See this video for more ---> kzbin.info/www/bejne/mmmlnGWgacmWY80

[@SnowWalker1]

All these videos and you don't have my dang problem ☹ My footrest padding popped off the footrest bars, whatever they're called. I've been noticing screws here and there that fell off onto the floor but I wasn't sure from where since the footrest has always been...not quite right.

[@SnowWalker1]

Btw, I'm a woman, and not too mechanically inclined.

[@georgedoughty6679]

Just bought a used lazy boy recliner. Don't have much money to repair. Trying DYI ,,,,not having any luck....I'll try some more.......wish me luck

[@ff-zg5ym]

My electric lazy-boy recliner foot rest is stuck in a half way position and will not close. Any suggestions would be greatly appriciated.

[@reclinerrepairguy4155]

@f f - Could be a mechanical or electrical problem. Have a repair tech check it out to make a determination.

[@ltlt733]

Thank you for your helpful videos! I have a 15 year old La-z-boy recliner that is worn and broken, yet I have to fix it due to lack of $ :( la=Z-Boy sent parts, yet.... Your vids helped me replace my drive rod, repair footrest mechanism, and figure out the reliner ratchet dilemma I had. ( I missed proper position of pawl release rod, used a repositioned retainer clip to fix, as removing drive rod again was not an option) I firmly believe Rube Goldberg designed this whole mechanism, hard to wrap my 64 year old brain around, age?

[@heatherlanoue8404]

Hi, found your great videos. I am actually looking for the silver "clips" that connect the springs to the coils. I'm missing two on my inheritanced 80s lazyboy!!

[@reclinerrepairguy4155]

Heather Lanoue - They are available thru La-z-boy (or one of their dealers). Since you're not the original owner, you won't have a parts warranty, but you can still order and pay for those parts.

[@heatherlanoue8404]

@@reclinerrepairguy4155 ok I will look, do they have a specific name that I can look for? Thank you for your time.

[@markkloth8912]

I watched and fixed my chair. Thanks

[@reclinerrepairguy4155]

@Mark Kloth - You're welcome!

[@kathleenmccarthy1801]

Thank you! You saved my chair!!

[@reclinerrepairguy4155]

@Kathleen McCarthy - Actually, you saved your chair -- congrats! :)

[@janicedoherty3905]

I just bought an old second hand Lazy Boy recliner. The fabric and wooden legs are beautiful, but the springs and mechanical parts are very rusty! I am 78, female, and I can’t push it to recliner position without someone else moving the back of the chair backwards. Then it goes smoothly. My son is coming soon and I am trying to search for replacement springs, but need your advice as to what else may needed for him to help ease the tension needed for me to recline. Any help? I have no knowledge of how old it is. It has no mechanical power and no levers, only push back by me!

[@reclinerrepairguy4155]

@Janice Doherty - For parts, check with La-z-boy to see if they're still available. For lubricating the mechanism, see this video ----> kzbin.info/www/bejne/gafZoYV_g9R4eas

[@ronglaze746]

I have an electric Lazy Boy. 2019 1HR530.I know it was designed to not lock when in the recline position (Lousy Design) But the Foot rest only lifts up about halfway maybe 3/4. It will not go all the way up or flat. Any suggestions?

[@reclinerrepairguy4155]

@Ron Glaze - Have an experienced repair tech inspect the chair. Many newer La-z-boy electric recliners do not open as far as older models. The tech can tell you if that's the case, or if there's a problem with the mechanism operation instead.

[@MyHairyChin]

I picked all these metal parts plus some, today, so these are all available in my area...

[@RodneyKarstens-kf7rg]

How would I go about acquiring the springs that connect the pivot pins on the 3 position mechanism? The pins and one spring are there , one spring missing Thank you

[@reclinerrepairguy4155]

@RodneyKarstens-kf7rg - Order the parts from La-z-boy. See this video to learn more -----> kzbin.info/www/bejne/a36ZlWdmp917Y9U

[@wilkyflex]

I have a relina-way chair and it feels like the bearings or rollers are bad. Are those easily replaced? Looks like they are riveted on. Can anyone help? Thanks

[@MrGoatWalker]

Do you know the size and thread of the scissor mechanism pin? I've stripped mine and I've only found replacement pins without information about the thread specs. Thanks

[@reclinerrepairguy4155]

@MrGoatWalker - Can you email a photo of the part? If so, send it to me at [e-mail]

[@stan8235]

Thank you as well! Simple fix for an stuck extended foot rest on my wife's wall hugger Lazy Boy. I would not have figured out the pin and spring position mechanism without watching your video. While trying to figure it out my wife remarked "does it need a little WD-40? Well, turns out it did, on the springs holding the position pins. Fixed! Now for the other problem. The rollers which allow the chair to slide forward while the back goes down, are worn. I believe at least one of them is damaged. Do you have a video that shows taking apart that part of the base?

[@reclinerrepairguy4155]

Stan - I haven't done a video on the rollers (Bearing Link Subassemblies) yet. They come with a plastic cover over the steel wheels for quiet operation. Over time, the covers will crack, split and eventually start falling off. This can make operation noisy and/or rough. Since the covers are not available separately, the entire Bearing Link Subassembly has to be replaced. Having said that, you can try this first: Remove the plastic plugs on the end of the base tracks (where the rollers travel). Clean out all the dirt and crud that accumulates in the track and causes rough, uneven operation. Also, remove any remaining bits of the plastic covers from all the rollers (if any cover is completely intact, leave it on). This should solve the rough operation problems. However, the missing covers allow the steel wheels to make contact with the steel base, which can be noisy. The only solution for that is to replace the Bearing Link Subs with new ones that will come with the covers installed.

[@stan8235]

@@reclinerrepairguy4155 Thank you very much. I am going to try cleaning out the tracks. You are right that it makes the operation noisy. I might try to replace those bearings (Bearing Link Subs) later as you mentioned. I will try this first and see. Thanks again

[@ChristianP85]

Thought I'd try this with my problem with my old lazyboy, you recline all the way back so you're laying down basically and it locks and you can't slide back, pretty frustrating though it is a 2005 model. Not sure if it's fixable though. Great video though ☺️

[@reclinerrepairguy4155]

@Christian P - If it's a manual recliner and you're referring to the back not returning to an upright position, check out these Seat Swing (the parts that control back tilt) videos: kzbin.info/www/bejne/m3i8hGRtnduCsLs and kzbin.info/www/bejne/oKuxYqtrn79gnaM If that doesn't help, have an experienced La-z-boy repair tech check out your chair.

[@ChristianP85]

@@reclinerrepairguy4155 thank you for the help, checked out the video's and managed to fix it by unwinding the springs fully :)

[@reclinerrepairguy4155]

@@ChristianP85 - You're welcome - good job!

[@gardengirl11ify]

Ours is about 4 years old and electric. Footrest got stuck in the up position. The motor made a grinding/working hard sound as we finally got the footrest down. Afraid to try using the footrest again. Any suggestions? Thanks. Great videos.

[@reclinerrepairguy4155]

Rebecca McDowell - Sounds like a lift motor may have failed. If you're a DIYer, checkout Troubleshooting Electric Recliners --> reclinerrepairguy.com/general_repairs.htm#troubleshootelectric If not, contact your La-z-boy dealer and have them check it out.

[@samuelthomassr.7051]

It works,thanks ,you have a new subscriber.

[@lorenzocole8166]

How do I actually change that mechanism ? I have to manually release the pin every time my wife reclines the chair. I know that I need to buy the part, I'm not sure what to call it to even order it. Thanks so much.

[@reclinerrepairguy4155]

See the video series -- 'Drive Rod Replacement' on the ReclinerRepairGuy.com website. Those videos include removing & reinstalling parts along the Drive Rod. The video where you placed this comment shows you how to disassemble the parts. Assembly is done by simply reversing these steps. Tip: Use a bent paper clip to stretch & install the small extension springs. It's easier than using your fingers & less likely to damage the springs. Here are the new parts you'll need to rebuild the older, metal 3-position footrest mechanism. * 3-Position Lever - 1 * Lock Plate(s) -- your setup may have 1 or 2, depending on the age of the chair * Pivot Pins - 2 * Extension Springs - 2 Be sure to add any other parts you need to your parts list, including pins & clips that hold parts in place. When in doubt regarding part names, you can always email them a picture.

[@teller1290]

Mine was bough in 01/04 and doesn't have ratchet looking gear thing. Mine just has more of a "U"-shaped hook thing on each side. Any idea what I can do?

[@reclinerrepairguy4155]

@teller12 - Not all La-z-boy recliners have the 3-Position Footrest feature. If you don't have the metal setup shown in the video, there is another type which uses the plastic 3-Position Locks shown in this video ----> 'The La-z-boy Recliner 3-Position Footrest.' [ kzbin.info/www/bejne/Y6awipynd9Vjr5Y ] If you don't have those, you don't have this feature. HOWEVER, if you check out the video I suggested, it will explain how you may be able to use the plastic locks on your recliner.

[@rondenhollander3832]

What size are the bolts that go into the footrest. I have to replace one for a family member that lives 2 hours away and I want to get it here before heading there. Are they 8-32, 10-24, or other size?

[@reclinerrepairguy4155]

@Ron DenHollander - Sorry, I don't know the size. You'll have to remove one & take it to a local La-z-boy dealer. Or, try a hardware or home improvement store where you can try to match it up.

[@roybrooks3913]

Have a lazy boy climbing foot rest is up no power got a coat of 68 on it what do you think the problem could be

[@roybrooks3913]

Code 68 on it

[@jsgll...godgunsliberty2025]

My 3 position lock does not look like the one in your video its a bit different, and I cannot figure how to replace both of mine broke I have a 2019 model do you have any videos of the new style plastic 3 position lock replacement.

[@reclinerrepairguy4155]

JSG II... God, Guns & Liberty - Yes! ----> reclinerrepairguy.com/lazyboy.htm#lazy3position

[@peterromano1911]

How do I adjust or repair the foot rest on the electric chairs ? My foot rest does not close completely.

[@reclinerrepairguy4155]

@Peter Romano - The first step is to determine if the footrest is being obstructed, or if there is a damaged actuator (or other part) that is causing the problem. Remove the back & turn the chair over onto its arms. Plug in the unit and open & close the footrest while observing the footrest & reclining mechanism parts in action. (Keep your hands aways from moving parts!) Your findings will determine your course of action.

[@peterromano1911]

@@reclinerrepairguy4155 Thank you.

[@cathystultz8379]

Okay, I don't want to purchase the wrong part. My Lazy-Boy footrest drops when I put the weight of my legs on it. I should contact a Lazy-Boy dealer and purchase a plastic 3 position lock. Am I correct?

[@reclinerrepairguy4155]

@Cathy Stultz - The first step is to do an inspection (or have a repair tech do one) to determine the cause for the footrest drop. Remove the chair back & turn the bottom over to view the mechanism in action while opening & closing the footrest with the handle. DOING ANY INSPECTION OR REPAIR IS AT YOUR OWN RISK!! The footrest can open or close unexpectedly, causing injury if your hands are inside the chair! Look for bent, broken or otherwise damaged mechanism parts. If none are found, note whether the 3-Position Footrest is controlled by metal parts or the black plastic locks. If metal, follow the suggestions in this video. If the plastic locks are present, remove them as shown in this video --> kzbin.info/www/bejne/Y6awipynd9Vjr5Y Reassemble the chair & test operation. If the footrest no longer drops, the old plastic locks were the cause. If it still drops with the locks removed, you (or the repair tech) missed the problem during the inspection phase.

[@cathystultz8379]

@@reclinerrepairguy4155

[@lexconor8498]

My older, inherited Lazyboy, while fully functional (rock, swivel, recline) makes quite a bang at the moment the footrest is released from the raised position . If i tip back simultaneously, i can avoid it. Is it broken? Or is that just how it is?

[@reclinerrepairguy4155]

Lex Conor - The noise you hear is the Ratcheting Recliner feature disengaging, and that is normal. You've figured out how to avoid making this noise by relieving the pressure on the parts before disengaging (using the handle to lower the footrest). Another method some people use is to place one foot on the floor (if your legs are long enough) and push back just before lowering the footrest. To learn more about the Ratcheting Recline Feature, see this video ----> reclinerrepairguy.com/lazyboy.htm#ratchetrecline

[@gailangeluski8700]

I wish I had discovered your videos before we got rid of one of our old lazyboy recliners. Do you have any suggestions for firming up the lumbar area in a lazyboy back? I really hate using those separately purchased lumbar supports and they ruin the appearance of the chair.

[@reclinerrepairguy4155]

Gail Angeluski - To add padding to the lumber area of the inside back, see this video --> kzbin.info/www/bejne/hpfNoY2wib2DeNE. It will show you what type of padding to use & how to fit it properly. If you don't have the 3-pillow back configuration shown in the video, you'll have to loosen the outside back panel to access the back of the lumbar area. Next, cut open the lumbar compartment from the backside. Install padding as needed. Then sew or staple the compartment shut & finish by reattaching the outside back panel.

[@hosamanisureshsuresh1500]

I'm suresh Hosamani I'm laz boy wark bost

[@nicolegoupil7179]

Replacing older metal parts with newer plastic ones? Wouldn't the opposite be the "better quality" option, more permanent fix? ? Are metal parts even available?

[@reclinerrepairguy4155]

@nicolegoupil7179 - When placing a part order with La-z-boy you can ask about the parts to make sure everything you need is still available. The metal configuration requires about 7 parts to provide the 3-position feature. And 2 of those parts -- the Extension Springs -- that hold everything together, are tiny & can easily be damaged (over-stretched) during installation. Also, the Drive Rod needs to be partially removed to install the Lock Plates. As a result, this repair takes some time & all 7 parts need to be in good working order for it to work properly. With the plastic parts, however, you only have 2 parts that can be replaced in less than 5 minutes (if you've done it before). And they can last a fairly long time. Keep an extra set handy & you'll be able to swap them out any time that it becomes necessary. Easy-peasy.

[@piche50]

do you know what size of springs I need for pivot pins I cannot seem to find them under the chair ?

[@reclinerrepairguy4155]

@Dar Piche - I don't know the size, but the Part name is Extension Springs. This is a common part that a dealer may have in stock. When requesting this part, let them know that they are part of the older 3-position setup, so they know exactly what springs you're referring to. Be sure to request 2.

[@23reynaldo]

My non has a 5 years old electric la z boy recliner and plastic mechanism that lift the footrest broke. They provide me the part Do you have any video how to replace it or advise ? Thanks

[@reclinerrepairguy4155]

Reynaldo Pena - No videos on that subject yet, sorry. If it's the plastic part that slides onto the Drive Rod, that's not an easy fix. I would recommend having a La-z-boy repair tech do that one. However, if it's not that one, the other plastic parts are pretty easy to replace. Contact your dealer for a sketch if you're having trouble visualizing how the broken part was originally attached.

[@tabhorian]

Perfect. thanks. You can fix anything these days with youtube

[@aszostek3799]

We have had our La-Z-Boy recliner for about 25 years! It is a great recliner. The footrest has been acting up lately, and today it would not go down past position 2. We were just about to toss it in the trash, but thought we'd check KZbin first. So glad we did. This was the video we needed! I removed the 3-position feature and we're just using it as a 1-position chair now. Will make a decision of whether or not to fix it later, if we can't find a suitable replacement. Thank you Recliner Repair Guy!

[@reclinerrepairguy4155]

@aszostek3799 - You're welcome -- good job!

[@IanPatton]

I can't do the work myself - arthritis - so I'll need to take it into a shop. How long did your repair take. The shop charges $75.00/hr so I'd really like to know. Thanks.

[@reclinerrepairguy4155]

@Ian Patton - It's about how long they take (not me) and what specific repair(s) they'll be doing. If they are experienced with La-z-boy repairs, they should be able to give you a quote after they inspect your chair.

[@IanPatton]

@@reclinerrepairguy4155 Thanks very much.

[@joecook]

Where do get the springs that go on the pivot pins

[@reclinerrepairguy4155]

The Extension Springs can be ordered through the manufacturer -- La-z-boy -- or one of their dealers.

[@TG-gq7dd]

My handle on my lazyboy is very hard to push and pull. Do you know what I can do to make it easier?

[@reclinerrepairguy4155]

@T G - I'd have a repair tech check out your chair to make sure there are no mechanical problems contributing to this issue. If your chair has an adjustable tension spring, they can also adjust that to see if that helps. If there are no mechanical problems, there are handle extenders (generally sold by medical supply companies) that may help. If none of the above suggestions resolves the problem, you should consider purchasing a power recliner or lift chair.

[@TG-gq7dd]

I turned the chair over and put wd40 spray on all the moving parts and the handle works much easier.

[@valeriefania6492]

Hi can anyone help. I just got 2 3 position recliners. I am having trouble closing them. I have it fully opened in the third position but when I try to close it it kind of clanks down all at once is is very loud. I cant seem to make it smooth close.I dont know what I am doing wrong,,, Any help would be appreciated. thank you

[@reclinerrepairguy4155]

@Valerie Fania - That's normal operation for this La-z-boy design. To avoid this sound, some users do the following: 1) If you have long legs, take 1 foot off of the footrest and place it on the floor beside the chair. Push back -- against the floor -- while closing the footrest. This will relieve the pressure. 2) Rock back in the chair just before lowering the footrest. This takes some coordination, but it works if the ratcheting recline is not maxed out (tilted back all the way).

[@Nancyandherfriends]

Omg this was my issue too! Thanks so much. Now my dogs won’t jump every time I close the chair!

[@jimike4716]

I turned my couch upside down and nothing obviously wrong. So I just oiled it, let it soak in. Moved the foot rest to work it in and it worked again.

[@lexconor8498]

Can you make a one position foot rest lazboy a 3 position by easily adding the part?

[@reclinerrepairguy4155]

Lex Conor - Yes, as long as you have a set of Rear Swings with the required cut-out shown in the video. Newer chairs will have this cut-out, while older models may not.

[@blairbunker]

The Spring connected to the bullet pin has a NAME the proper vocabulary used in a parts search would be?

[@reclinerrepairguy4155]

@blairbunker - Timestamp: 1:45

[@EntertainmentHub92]

Can you help me I need my foot rest keeps falling down when I put even the weight of my legs on it it's a lazy boy idk the model number

[@reclinerrepairguy4155]

@EntertainmentHub92 - If you've inspected your mechanism Leg Extenders, as suggested in the video & found no problems, you can try disconnecting the 3-Position Lever (or 3-Position Locks, if you have those). If the footrest still won't stay up, have an experienced repair tech take a look. However, if the entire chair pitches forward, but the footrest stays in the fully open position, this is a Ratcheting Recline problem. Again, have a repair tech take a look.

[@lindacharlton8798]

I have a lazboy but my does have have the metal part for the foot rest my is just a wire.

[@juliawoodhouse8541]

Why would my footrest just pop up when I sit on it.

[@reclinerrepairguy4155]

@julia Woodhouse - That's fairly common with cable release recliners. If the footrest is not closed completely so that it latches shut, it can spring open on its own.

[@rosies401]

Who in Cheyenne Wyoming fixes leg rests on a discontinued recliner?

[@corinnelivingston8876]

My remote ( not wireless) is not getting power. Green light on box, no lights on remote. Chair is 10 yrs old

[@reclinerrepairguy4155]

@corinnelivingston8876 - Basic electric recliner troubleshooting tips ---> kzbin.info/www/bejne/p6qmZqKoZr6Zma8 More tips on finding help with your repair ----> kzbin.info/www/bejne/aXi7aX6IiJeijLc

[@corinnelivingston8876]

@@reclinerrepairguy4155 thank you so much. I have followed all the steps and will replace my remote.

[@thesweetestgrl]

I'm having a problem with mine...its not the 3 position one. I can't close it smh it is a lazy boy

[@reclinerrepairguy4155]

melissa lopez - Contact your sales/service agent to report the problem. If the chair is less than 1 year old, you should still have full warranty coverage. If it's older, they may still be able to diagnose and repair your problem. If not, they should be able to refer you to someone who can.

[@richardpflieger2049]

Bravo!!!

[@donaldcook5339]

Can I send you a picture of my problem

[@reclinerrepairguy4155]

@donald Cook - Ok, send it to -----> [e-mail]