How to Replace Front Lower Rearward Control Arm 2006-10 Dodge Charger

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@tyronedavis1672]

I know this is a 10 month old video but did you start on driver side.

[@liamauigbelle4588]

I do believe it is recommended to put the weight of the car on the front suspension and then proceed to torque all the bushings replaced to the required torque spec in order to avoid premature wear on the bushings.

[@jamesbarlowjr.3762]

Liam Auigbelle That’s what I thought. I usually put a 4x4 block on the floor jack on the hat of the rotor and jack it up to where your almost lifting the vehicle then tighten.

[@2004redspecv]

yes you are correct, you must have the vehicle weight on the suspension before torquing down to correct specs. we do this to center the bushing to be at zero tension when the supsension is centered.

[@pochomachuca9629]

Yes, I did this on jack stands, so I put my floor jack under the rotor and lift it until the weight of the car was on the jack, then I torqued everything on. Still went to my local Firestone and they did an alignment, just to be safe

[@mikesanderson72]

It's really hit or miss with these videos on being helpful with fixing an SXT 2010 charger AWD.

[@Wastelandyung24]

My mechanic told me get either this one or the forward one how to I know which one cuz we don’t understand each other lol sorry... help ? Tire like jumps a lil when I break should I just get both

[@Mopar3.6LV6]

Is this the same procedure for a 2018 Charger SXT RWD? Everything looks very similar. Gotta replace this part. Found that the bushing is cracked.

[@Andre-hq8bb]

what is the tourqe spec on the wheels on the SRT 8?

[@darrenclark3946]

Does the ball joint move a certain way when I install it for the lower rearward control arm period for 2009 Dodge Challenger RT. Does the ball joint move in the 360 degrees

[@kylerchaffin5814]

My brother in Christ there was smoke coming from that metal bolt & nut. Slow er Down

[@sr8shoota]

What is the name of tool at 1:47

[@03creations34]

jaw puller

[@eduardo7193]

I wish I can see the whole video u know with editing I gotta do upper lower and lower rearward tomorrow 😫

[@gyver471]

Where are you located? I need it done on my car I have a charger.

[@gregbrewerjr7676]

has anyone used any of this TRQ stuff?how does it hold up over time?cant find any reviews

[@pochomachuca9629]

No, but I’ve seen videos of people who have bought and installed their products, and so far the reviews are not good. For the way they describe the quality of the product, I’ll put them on the same category as Detroit Axle

[@kylerchaffin5814]

Bro has successfully vandalized and destroyed this car, violated in every way imaginable

[@deaconwest]

You make this look so easy

[@lacitykid9224]

Bro your supposed torque the rubber bushings only after you preloaded the suspension 😮🥲 That would cause premature wear if not instant damage of the new bushing once you lower the vehicle and the full weight of the vehicle lands all the suspension and steering components where they are supposed to be with the wheels on and moving down the roads 🫠

[@chargerjai0078]

Could you all do a video on how to change the rear control arms for rwd Dodge Charger 2008, it’s no videos out there

[@TRQ]

+Charger Jai 007 We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-TRQ

[@justheretowatch9451]

looks like you threaded that bolt bad.

[@torrenceestes1443]

Yo thats what mine looks like... It's in two pieces though is that not normal?

[@jomglew]

Nice

[@donpoochi]

how much this repair cost about

[@mediaguy4037]

$800

[@christianwilliams1894]

My mechanic charged me 100$ and he got it done in no time and my car drives smoothly down the highway.

[@TRQ]

+Ćhristian Williams Thanks for the feedback! 1aau.to/m/Shop-TRQ

[@beastinowt3569]

2.5hours tops unless it’s a rusty mother

[@masonhawkins2431]

Your videos are always great but i hate the way you say vehicle.

[@Chriselectricfingers]

No preaload in the CA !!! Then turk to 130 buddy or that rubber bushing will desinagrade prematuraky!!! Smh

[@michealpatterson3945]

He forgot the torque for the bushings of the front lower forward control arm

[@TRQ]

+Micheal Patterson Thanks for the feedback! We'll pass this info along to our production team. 1aau.to/m/Shop-TRQ

[@Chriselectricfingers]

U turk bolts in CA under preaload not in the AIR!!! SMH

[@MostGenericUser]

Nice