How to Replace CV Axle Assembly 2008-2013 Nissan Rogue

Buy Now!
New CV Axle Assembly from 1AAuto.com trq.video/ib-1...
This video shows you how to install a new CV Axle assembly in your 2008-2013 Nissan Rogue. A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications.
This repair was done on a 2009 Nissan Rogue S 2.5L Sport Utility 4-Door AWD Automatic and the process should be similar on the following vehicles:
2008 Nissan Rogue
2009 Nissan Rogue
2010 Nissan Rogue
2011 Nissan Rogue
2012 Nissan Rogue
2013 Nissan Rogue
Tools you will need:
• Flat Blade Screwdriver trq.video/obiA...
• 18mm Wrench
• 13mm Socket trq.video/obsB...
• 18mm Socket
• 21mm Socket
• 32mm Socket trq.video/ocx-...
• CV Axle Shaft Popper Tool
• Dead Blow Hammer
• Pliers
• Socket Extensions trq.video/obsB...
• Torque Wrench trq.video/oaDb...
• Cotter Pin
• Gloves trq.video/o3I-...
• Safety Glasses
• Bucket
• Chisel trq.video/okH-...
• Floor Jack trq.video/o4i-...
• Hammer
• Jack Stands trq.video/oSI-...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Nissan Rogue 2008-13 1st Generation: • Nissan Rogue 2008-13 1...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@619enigma]

You don’t need to remove the ball joint just loosen the strut bolts and turn the wheel to the right and let the top bolt slide out leaving the bottom bolt loose but not out all the way and if you have to take the second one out it won’t do any thing to the strut as long as it’s lifted off the ground so no tension is there, and let the strut lean forward so at that angle the axle will slip out easy I’ve changed two of these now I’m on a third one and bearing

[@guerramundial9868]

I love TRQ videos, and parts.

[@stratusboy]

Removing tie rod end from knuckle makes life a lot easier when doing this

[@pavelaevii6687]

Instructive and understandble thanks

[@WillieFufu-lo1nb]

Is this the same process for the 2013 to 2020 Nissan Pathfinder? It looks the same.

[@billwTCan]

Wheel alignment afterwards needed?

[@ConnorSinnott]

Removing the ball joint from the knuckle was difficult. We ended up using a crow bar, placed vertically so the curved bit goes around the knuckle to the bottom of the joint. Then used a sledge on the top of the crowbar to knock it free downward.

[@jaredk777]

Where can I find a slide hammer with the claw?

[@voragonema]

Great! So clear, thanks!

[@witarzan]

How is this video different than the other video?

[@lsologaistoa]

Question My 2008 Nissan Rogue’s dip stick has the HOT label on it, but it doesn’t have the “greater than & less than” symbol marks. It does contain the hashed area and the two notches. The Hayne’s manual states to fill the fluid between the two notches once the transmission fluid is brought to hot temperature. You’re saying to fill it to the HOT marks. Which is correct? By the way, the operator’s manual doesn’t give any guidance.

[@LUISSERR89]

Thisone needs a new lower control arm ball joint too

[@billwTCan]

Why cut the Cotter pin instead of filing both sides?

[@elymannylem9126]

How many pounds is the slide hammer?

[@codykellogg2540]

Ones passenger side the other is drivers side trq has videos on both