How to Replace Front Lower Ball Joints 2003-2007 Honda Accord

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@user-wb9wk3gw7q]

Great video! You left out the part where he puts the retaining ring back into the knuckle.

[@dknight211]

While replacing one of the front lower ball joints on my 2007 Honda Accord, I used a ball joint separator instead of a pickle fork. As I tightened down the ball joint separator with a hand ratchet, it shot out to the side (with all that built up energy from being tightened down) and hit my gloved thumb and almost broke it. I can see now a pickle fork is much safer!

[@jonathanbarros9948]

great video and very well explained, going to help a lot with mine tomorrow

[@richardspaulding5035]

Why did you not show reinstalling the retaining ring????

[@marshallpomeroy224]

Any recommendations for getting the axle back in place with grease fittings on the ball joint? The ball joints I purchased came with grease fittings

[@christophergrandison5365]

Great vedio, but I never saw when you install the hub.

[@Waldo1982]

Axel lug on a 4 cylinder is 32mm and 36mm on the v6 I believe

[@rubensolares9929]

Exelente muy didáctico lo mejor es la inclusión de los torques gracias por compartir.

[@rubencarorubio4992]

Good job bro, i love Honda

[@josefranciscoesquertalaman3827]

Presente en las aventuras de mecánica automotriz TRQ, cordial saludo desde Navojoa Sonora México 🎉

[@ShaunRygg]

At what point did you replace the bearing? That’s brand new

[@jrwgss1971]

Anyone who owns a air chisel, likely doesn't need to watch this video. Since you used the ball joint press for the install, you really should've shown how to use it instead for the removal of the ball joint. And as 2 others have mentioned, where did the brand new hub bearing magically come from???

[@LuisMartinez-pd1bl]

You left A1 Auto ??

[@elmerorellana9061]

Muchas gracias e aprendido mucho con tus videos y también e ahorrado $$$$

[@atlflores9623]

Anyone know where I could get a tin cap that goes behind the wheel bearings ? 8:00 is what I’m referring to

[@danp7463]

That lower ball joint look like it's the wrong size. There's a few options on ball joints when it comes to Hondas.

[@ramonesfreak2010]

PSA: replacing the bearing/hub isn’t needed for this install. Its new because they most likely filmed a video for the procedure to make more content. Theres no point of taking everything apart every time for each video. They recycle clips and do everything at once.

[@bluray4687]

You never showed the reinstallation of the tin

[@TRQ]

+@bluray4687 Thanks for the tip! We'll pass this info along to our production team. 1aau.to/m/Shop-TRQ

[@mariarivas6377]

Thanks.

[@TRQ]

+@mariarivas6377 Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@kongxiong6005]

I am almost 100% sure that you're catching socket is not big enough. I have a socket similar size and the ball joint is too long

[@SashaNem]

thanks

[@keijogronfors925]

Thats not so clean when you open that and it isnt so easy to put the paljoin out

[@christophergrandison5365]

Great vedio, but I never saw when you install the hub.

[@christophergrandison5365]

Great vedio, but I never saw when you install the hub.

[@christophergrandison5365]

Great vedio, but I never saw when you install the hub.