I prefer it with the wire clipped. However, I love the idea of a switch on the back of the set. It's the best of both worlds in my mind.
@ezl70527 жыл бұрын
I suspect the wire is part of the AGC circuit and the switch idea might cause a problem if it's activated with the radio on. RS had real good service manuals and it would be nice to look at the schematic to see what part of the circuit the wire is used in. Thanks for the review.
@SpectreOZ7 жыл бұрын
I prefer performance with the Wire clipped (much smoother tuning) but as an alternative to a switch how about a variable resistor? that way you could tailor the mute Vs. noise effect to your most acceptable compromise...
@martinmartinl44207 жыл бұрын
I don't call cutting a wire really a mod. I like muting while tuning better. But it's up to the individual's ear which effect they actually like. I think the switch idea is also doable.
@william_k4arx11 ай бұрын
I know this is old but couldn't resist. No pun intended. Personally, having already getting this far, I would either add a mono 3/32 plug and receptacle or the like. Maybe add an external switch to activate said circuit.
@TheRadiogeek7 жыл бұрын
You could drill a hole in the back panel and install a switch. I don't know if it makes that much of a difference to be worth it or not. I would need to play with it some more to decide. Could you tune in some stations with voice or music and then tune around the so we can hear the effects of the mod better? Thanks.
@hamrad887 жыл бұрын
I listened to it both ways after the show and I am still on the fence.
@richard83426 жыл бұрын
It seems to me, if you are dx-ing low sig stations by ear you need the mod. I do not see why some one would want the VFO to mute when in use. Very good video. Thanks
@hamrad886 жыл бұрын
Agree 100%
@Littlelewie1513 жыл бұрын
I would just put a high cut filter in it for the noise. Mike's radio repair has a video on doing them on cb radios. Its a simple capacitor from the volume control to ground.
@jihad3557 жыл бұрын
hi, i have same radio and same problem om MW 510 to 1720 Khz i canot receive any radio
@TheOpenAirGarage7 жыл бұрын
You could extend the wires and add a small switch to turn it on and off.
@hamrad887 жыл бұрын
I think I mentioned that idea.
@TheOpenAirGarage7 жыл бұрын
hamrad88 yea you did right after I commented. I should have watched to the end before I commented.
@hamrad887 жыл бұрын
No problem.
@jaysonhaworth55312 жыл бұрын
After about 5/10 seconds on AM mine goes silent all others you an hear any ideas
@driverfilmsshortwavechannel7 жыл бұрын
I think the switch idea is a good idea, particularly if the signal is weak and in the noise.
@hamrad887 жыл бұрын
driverfilmsshortwave Thanks
@watershed447 жыл бұрын
+hamrad88 I agree with you Tom, in this case it seems like the MWT function is not to big an issue with this radio. But I agree the manufacturers should allow the consumer to chose MWT on or off to their liking. A cheap way to please everyone.
@hamrad887 жыл бұрын
Thanks for your comments.
@krzysztofbednarek94855 жыл бұрын
Good job , Thank You
@hamrad885 жыл бұрын
You are welcome.
@LegacyLost7 жыл бұрын
I had that Lowbander guy do a few mods on mine which is the first model non a or b ..... He did the mod you did,added some foil tape in the case to reduce stray RF,did his listed NB mod but it overloads and distorts the audio with it on when receiving strong signals,also do you get a power supply hum with the radio on and volume off at all?Mine does that ..... I can always tell if I forgot to shut it off cause I can hear the hum ... 73
@hamrad887 жыл бұрын
No hum from mine.
@metusa6666 жыл бұрын
No hum from mine sometimes the transformer coil or laminations may be a little loose. Try plugging in a different supply via the external power jack a cb power supply would do
@bilkenhampton7 жыл бұрын
Works great on my 394... b series on a more popular ie...80 meter lower side band that's where this radio sings
@hamrad887 жыл бұрын
Thanks for you comments.
@petergore1972 Жыл бұрын
Peter Gore Seer, I Have One I Put A Extension Speaker To With A Bit More Base,My Speaker Is 5 Inch, And It Help To Loose The Crackle, That Little Ariel Is Fantastic,It Screwes Into The Board, I Am Not Going To Tamper.
@bretwayne83027 жыл бұрын
I think it's better cliped!
@hamrad887 жыл бұрын
I am still on the fence after listening to it both ways after the show.
@vonzigle7 жыл бұрын
I think that even though the audio is not muted, the synthesizer is still going in 5 khz steps. So it is only a chance that you will catch a signal going by 5 MHz (in this case)... Think that if this were my radio, would leave it unmodified.
@metusa6666 жыл бұрын
I pot a miniature toggle switch on it works ok I switched it on and off with the set switched on it hasn't blown anything yet time will tell i'll let you know if it does