Truck hub greasing| Rear wheel hub greasing skills | смазка ступицы грузовика | Indian truck

"truck hub greasing"
"rear wheel hub greasing"
"vehicle hub greasing"
"hub grease"
"truck hub grease"
"how to hub grease vehicle"
"tata truck hub grease"
"best hub grease"
"hub grease work"
"how to hub grease big vehicle"
"hub grease by hands"
"Leyland hub grease"
"Velvoleen hub grease"
"Bosch hub grease"
#hubgrease
#truckhubgreasing
#howtohubgrease

[@MrUnderwurlde]

From the repair manual. "Torque the hub retaining ring to 13 heavy hammer blows"

[@TylerDurdenFL]

That's spec, right!?

[@laverdadesmejor]

you forgot to specify the size of the hammer!

[@trcythmpsn]

We just use torque guns until they make a different noise and that's good enough 😆

[@MrUnderwurlde]

@@laverdadesmejor I did...."heavy"

[@dell7054]

It's not America dude

[@kylenevel8809]

My heart sank a little when he dropped that bearing onto the mat and it slid into the dirt

[@JoeMama-ke1so]

That and also they contaminated the brake shoe. Pretty funny watching this as a semi truck mechanic.

[@Trinida374]

No need to worry it was going to get clean and regrease anyways

[@nipperdog7777]

Same. OMG and that solvent and no gloves. Do those guys make it to 50 years old?

[@weeb3277]

3:46 then hit it over a rock after washing it

[@shirsendumaiti5682]

@@nipperdog7777 yes they do, not a snowflakes like yall. And indian roads are punishing for these trucks, they kno what they are doing.

[@Kami_kaze808]

I was soo relieved when i seen them use new grease. At first i thaught they were going to reuse the old grease they were harvesting

[@BoopSnoot]

Don't be silly of course not they'll use that for frying up their lunch

[@TruthHurts2u]

Damn, I've been doing it all wrong. I never knew you had to bang the bearing on a rock before installing it.

[@ShawnTheRazor]

How else are they going to destroy the bearing before installing it?

[@SubramaniamLakshminarayanan]

See all the mud on the floor? They fell from the bearing after being dislodged from that bang on a rock.

[@DevilDaRebel]

@@SubramaniamLakshminarayanan See the chips and structural damage over the banging? The

[@akidim13]

OSHA inspectors would of dropped dead the second they saw no gloves being used

[@dtsang508]

Ain’t nobody got tam fo gloves…

[@aaronm.3581]

Who cares?

[@UndefinedBailiwick]

Sandals are standard workwear for them at construction sites, they don't really have any type of OSHA program.

[@lt4324]

@Mike Studmuffin LOL, I and many mechanics from my time have NEVER USED gloves when working on machinery and my vehicles for over 50-60 years! I used to work with SOLVENT for cleaning, even gas and trans fluid. It just never affected myself or relatives. I tried gloves once and could not stand them, too sweaty and could not grasp small parts at all. It may be good for YOUR generation with safety issues and or policy, but I never had any of my relatives who lived well into their 90's die of cancer, well I take that back, one did but he was 88 years old AND did not want treatments. I NEVER had issues because of no gloves also. It depends strictly on the person and their heritage/ Genes. I for one, never will use gloves but then again I am from a different time than yourself, and I do not mean it as a bad thing. Take it ez, Tom in NV

[@NeonAstralOfficial]

@@lt4324 yeah bro you can brag about "your time" or whatever. But you can't deny how fucking unhealthy that is considering more "complex" mixtures nowadays that have to meet arbitrary modern standards, new ways of processing these chemicals with new additives making them MUCH more dangerous. Not to get into your DNA which you coulkd have resistance to this shit, some people will just look at that and get cancer, not everyone is "immune" to chemicals like you are. With your "abilities" im sure you could brag about "back in my day we handled Uranium with bare hands" YEAH SURE buddy, "back in your day" you prob snored metal shaving for fun and drank gasoline too, look how durable you are everyone should follow your dumb ass example.

[@ImNotADeeJay]

For no apparent reason,I feel the urge of washing my hands

[@trevor.o6047]

Exactly what i thought lollll

[@ricardobocus6304]

Red tacky grease, the worst...

[@1marcelfilms]

Hand wash and a ton of moisturizer

[@luna-pw9ln]

No wonder that Bearing burned out you aint supposed to have 10000' pounds of torque on the Bearings

[@x-man5056]

tight as it will go, plus 1/4 turn. Cringy.

[@dave161141]

The clearance is set by 34 blows of standard shop hammer. And we here bother with torque wrenches... "first world problems" :D

[@twiggy6899]

At 2:06 he's holding the sleeve that goes between the inner and outer bearing which sets the preload. basically making it impossible to over tighten the jam nut and put too much preload.

[@JohnDoe-hg9pj]

Grease looked like it was done recently when they removed it. Also why would you grease a bearing in the dirt?

[@cannotwest]

Isn't it toxic for the hands?

[@user-wj9wq7mk4h]

No, it actually kills the germs on your hands.

[@ErikS-]

They are putting a "little bit" too much grease in the bearings. So much grease will create viscous friction, increase the temperature and start decomposing. They really seem to have no clue what they are doing.

[@austinlane5533]

I feel like most of these "repairs" are only going to last a few hundred, maybe 1000 miles and they're right back in the shop getting the parts "fixed" again. People are praising these guys and they're literally packing dirty grease into tiny tolerances that hold alooot of weight in the load. No way these repairs last long.

[@seana2375]

It's because it's a shit hole desert country

[@gasa1165]

Yeah they are packing the bearings like it’s mustard grease, if they used the mustard grease then it would have been ok cause it’s more liquidy than the red grease.

[@polarbear1034]

Yeah at that point with that much grease you’re just going to get a churning effect and high temperatures and all that excess grease will just get pushed out of the way, I think common practice for people that don’t know is if I put as much grease as possible it will be better but really a 1/3rd packed bearing would actually run cooler and have a longer life cycle as compared to a 100 percent packed bearing

[@shirsendumaiti5682]

Bunch of western snowflakes lmao

[@ДенисПетров-п3в]

Кругом песок, меняют ступичный...

[@WilliamVG]

No protective gloves from touching petroleum chemicals? Ok....

[@elnauta9525]

This will last few month, in the best scenario. This is a very good example how not to do this job, is a disaster.

[@lesschattermoresplatter5769]

Everything about this video was cringe worthy

[@tzon6802]

just like you

[@lesschattermoresplatter5769]

@@tzon6802 just like your mom…

[@mart43]

They do there best with the stuff they have show some respect my dude!

[@lesschattermoresplatter5769]

@@mart43 I’m not talking about the work they do. I’m talking about everything that has threads or grease on it, they throw in the dirt “dude”. No respect earned, no respect given and I don’t give out participation trophies.

[@jackcameroon8423]

Who taught you to work on axles? The Flintstones?

[@santarsbuilders7905]

Очень хорошо проделали работу ребята молодцы смазали на совесть🤝🤝👌👌

[@circuitrex]

And this my friends is how you get hand cancer.....

[@SniperMakedonero]

Great job. Imagine if this boys are having clean workshop with newest tools.

[@dell7054]

Not gonna happen it's india

[@josephwillis1581]

These guys either don't know they should be using gloves or they don't have access to them.

[@少佐-i9d]

素手で作業してて疾病が気に成るな 　(^○^)きゃははははははははははは～♬ぷっ

[@coltonadkins7929]

It'll be in again in a week for the same issue. Idiots clearly don't know what early wear due to dirt and sand is.

[@laverdadesmejor]

This is a very good job, at least this is how I was taught, but then I wasn't working in THE DIRT!

[@chunkyhebrew8805]

Yooo... And I think I'm doing something when use bleach/Lysol wipes bare handed 😄

[@davidhumphries7092]

What in the name of Merlin the patron saint of hiways is going on here? There should be 90 weight gear oil in those hubs!

[@harrysingh23116]

its grease idiot

[@uu9rj]

@@harrysingh23116 Hes far from an idiot... Most hubs these days use an oil bath and for good reason, lubricates better so they fail less often, the only real advantage to a grease bearing is that if you have a seal go you dont lose all your lubrication at once, but the downside of that is if you have an issue in a grease bearing it can take awhile to make itself apparent, whereas with oil you can see the problem right away and address it.

[@x-man5056]

@@uu9rj spot on.

[@x-man5056]

@@harrysingh23116 look in the mirror, David is right.

[@austinlane5533]

@@harrysingh23116 Hey, idiot.. there's a big difference in grease and gear oil.. go back to whatever it is you do. Comments aint working for ya.

[@tima.478]

Umma need to check the torque spec. on that wheel nut...

[@x-man5056]

was it 5 hammer smacks or 7?

[@henrygoodbar9477]

xD

[@Prosmotren]

5:23 soon you will be disassembling again, because you knocked the oil seal on the axis.

[@whiteknight1442]

Hope it will brake when needed

[@vxpm5817]

LMAO

[@MPhazers]

XD

[@kaszojadpolak1560]

Bozo

[@user-kx3xg1dk8p]

Took me a couple of seconds, but then it hit me like that truck

[@dammdaniel9953]

How stupid can you get they are just greasing the bearing not the brake shoes dumbass do your research before commenting something stupid and dumb .

[@gumballer133]

I can't say I have ever seen an axle like this that isn't oil lubricated, even if it isn't a drive.

[@TrillShatner]

In poor areas, all the lowest end tractor/trailer/work vehicles are completely made from spare parts. After about 1million+ miles the lubricant in them has long since worn down into a substance thin enough to escape the housing until it begins to seize up~

[@FerrickOxhide]

Worked on some trucks from the fifties and the gear oil seal was on the end of the spindle, outside of the nuts. All bearings were greased.

[@gumballer133]

@@FerrickOxhide Ohh wow, yea I could see that. I've never owned or worked on any trucks older then the late 70s.

[@wes326]

Hurts my knees watching this.

[@applejacks971]

Vanguard dry van's have oil less hubs. We have a couple 2021's that are like that.

[@londzale3163]

Reuse the same grease ver resourceful technicians

[@rpthrottle9237]

Not worth it Grease was good

[@muhammadaditiyoabiyoga3064]

Agreed

[@jjano2320]

Well, at least they check it and don't wait until there's a problem.

[@jwdean9163]

Sand and grease, good combination.

[@dmitriybelousov7246]

Смазка с песком это видимо там норм ... а так да стараются

[@Lomaster-v9f]

Они вообще знают, что существуют другие инструменты. Трешетка головки)

[@ЛераАндропова]

Не говори! А ещё кровь из глаз идёт когда они руками без перчаток и моют детали и смазывают. Фу бляя

[@rmam2656]

Poor hands 🤦🏻🤦🏻🤦🏻

[@tima.478]

Yeah, this dude probably has 7 different kinds of 'grease' monkey cancer coursing through his body!!!!

[@Rajesh-pm2xj]

Now i get it , those ugly grease are those used for shop shutter serveice in India .....Damm cheaters

[@themancalledx1342]

Few pounds of dirt/dust in your grease is juust fine

[@DiscoMiata]

They get what they pay for….cheap labor But to be honest this is how the normal conditions are their

[@patrickhutchins6935]

does anyone in India wear socks?

[@seana2375]

Really earning that 14 cents today

[@jorheybhai]

That's the way our mechanic works Why you need gloves They are practical mechanics not only theoretical like other countries have They can rebuilt engine and gear They can hear the sound and can tell what's wrong with your vehicle

[@volkane33]

Bro made this trucks wheels cleaner than an average Indian street food

[@brucedale4465]

Oh I can’t watch another how to be a mechanic in india!!!!!!!!!!!!

[@LuisRamos-nn9qk]

Just like an LMTV lol, good times

[@richardholmes9295]

Most mechanics have a set off different size spanners these have different size hammers.

[@Heisenberg8307]

😄

[@theponz618]

Nothing like washing up in a bowl of cancer.🙄

[@НикИванов-ф2к]

I respect workers! They honestly earn their living!

[@joro808]

My dad works on semis and he uses power tools and that isn't easy work

[@StreetTramper]

Better replace the wheel bearing as well

[@kaisyaya8492]

i reckon they maintain these wheels regularly in order to make the bearings last longer, since new parts are too expensive but labor is cheap

[@stardog2779]

Im pretty sure new parts are hard to come by. This isn't America where you get on your car and drive to o'riley or autozone

[@coltonadkins7929]

@@stardog2779 you drive to neither of those for components like this. And they're available in America, and expensive as hell. But for good reason. Notice how he got everything all nice and muddy and dirty during the cleaning process? I'm sure they maintain it regularly because it fails once a week due to their terrible ability to keep contamination out of their bearings.

[@jefftate01]

Be sure and dump solvent on the brake pads.

[@greasyviking]

Gotta love the preload technique

[@jonfaber4836]

Just gonna fix everything right there in the dirt

[@WalnutTorneo]

国柄もあるのかもしれないが、全てにおいて酷すぎる 部品や工具の扱いが雑過ぎてここに仕事を頼もうとは思わない 地獄

[@fuffoon]

Mmm, rasberry jam and roller bearings. Delicious!

[@JB-ef7ks]

Apparently nobody there knows how to properly pack grease into bearings!;

[@lt4324]

Are you refereeing to a Grease packer OR by hand. I just push the grease as best I can into the bearings, and not just rub grease all around as MAYBE they did.

[@Power-qh9pm]

Too much grease and it'll just get clogged with dirt. The right amount is always better than just slathering it on

[@runar4993]

It still looks like way too much for me I guess I'm wrong lol

[@Power-qh9pm]

@@runar4993 no you're right. He's using entirely too much. It'll just attract dirt and debris easier.

[@DanS-dc5vu]

@@Power-qh9pm wrong. Bearings are SUPPOSED TO BE PACKED WITH GREASE

[@magnetomusic13]

I can teach this guy how to work clean and proffesional 👌

[@Ramirez83786]

Easy talk if you're not from there

[@magnetomusic13]

@@Ramirez83786 all about use ur braing boddy

[@seanthebaptist6757]

You probably wouldn't last half a day over there

[@magnetomusic13]

I bet you wont last not even a week working wiht my boddy you will quit in 2 days maybe same day

[@magnetomusic13]

@@seanthebaptist6757 lil boy am from the island so am used to head boddy 🤣🤣🤣

[@asmotormechanic2040]

Aapane hub khola aur usko Greece bhar ke fitting karna bhi shuru kar diya ustad ji mujhe aap yah bataiye aapko kaise pata laga ki yah hub tight hai ya dhili hai

[@robertcachia6484]

That's what I like about KZbin you can always learn from other people's mistakes.

[@catchbug9]

한국 군대 운전병은 이 작업을 자주합니다. 일명 허브까기.. ㅋㅋ

[@drumtwo4seven]

Relaxing

[@shubhamsaindane]

Guys I think you not to be understand has guys methods and tricks Indian mechanics work on experience besis not to be companys manual , in India 60% mechanics are not educated but this guys experience are autstanding , and USA mechanic are changing car engine oil charges ($ 25 doller )in Indian currency 2 thaugan rupees and Indian mechanic full vehicle service in 500 hundred rupees this is big difference USA mechanic and Indian mechanic and his salary... Don't judge a book by its cover I am mechanic in india 🇮🇳🇮🇳🇮🇳 24×7 mechanics support

[@АнисГареев]

Дай бог вам здоровья ребята! Удачи!

[@kingdude2089]

I have never changed seals that didn't also need new pads from the hub oil pouring out. I have no idea why the bearings went bad before the seal.

[@HeyDude93gt]

I never changed big truck seals that didn’t use gear oil

[@applejacks971]

@@HeyDude93gt we have a couple 2021 Vanguards vans that are oil less hub. Grease only from the factory.

[@Bialy_1]

"why the bearings went bad before the seal." overloading of the truck... that is most likely why. In 3rd world countries they often putting cargo in the truck until there is space in it and do not care how many tons they loaded in it...

[@mx4menot4u]

I’m sure his hands would give mine blisters if I gave him a hand shake.

[@prajjwalchaudhry9277]

Idk u are such pampered

[@belalevai8721]

Magyarországon a szerelök nem ismerik a zsírt.

[@gx8raympm2zj54]

베어링보다 사람이 먼저 소모되겠네 구리스를 베어링에 바르는 건지 손에다 바르는 건지 아마 장갑을 줘도 귀찮아서 안쓸거야 그리고 저 맨손으로 밥을 먹을거니까 그야말로 기름밥이네 아프면 아픈대로 죽으면 죽는대로 산다

[@stephenstephen6754]

Huga buga job

[@Im_Munsan]

20년전 운전병으로 복무 하면서 군대에서 했던 거랑 똑같네.. 나 저기 가서 일 할수 있을것 같아. 베어링에 구리스 넣을때는 탬버린 치듯이 넣어야 하는데..가스켓 없어서 초코파이 박스로 만들고…

[@truthfulteachingsautorepai5475]

Those bearings were packed correctly If any of you are not diesel mechanics you should shut up . I pack bearings all the time and they are packed this way from the factory with lots and lots of grease . They also did not damage the seal when putting it on the axle They did a great job for not having all the proper tools .

[@naginato4841]

The leaf springs on this thing is crazy

[@greasyviking]

This video send my anxiety into full blown WHAT THE FUCK BRO!!! mode. Bring that batch by the shop I'll rebuild em all on the house

[@mikanov100]

Im sure they cant read... there are warnings on all the chemicals they use in this video... but facinating none the less

[@юрий-л4л4к]

Твою мать , я не увидел что ставится сальник внутри, или это как то по другому работает.? Извиняюсь просто не заметил.

[@xRENEGADE156]

The thing that gets me about all these kinds of videos is that the dudes are doing all this heavy duty work in fucking sandals

[@chubbyjohnson5480]

Poor guys trying to earn a living. I'm not going to pick their efforts apart.

[@Ardeact]

wow they have to maintain a bunch of these trucks without power tools

[@mattfillmore6297]

NOT CORRECT , He didn't use 6 cans of brake clean

[@유한경-d5n]

장갑 끼고 작업 손 다침 항상 건강을 챙기자

[@senorburrito1]

I think we can all agree, that his hands stink, and they have since he started working here.

[@sluge1]

Tara is a good track from India

[@КириллЗубков-ж3ю]

3:02 а колодки не судьба снять, чтобы на них не попало дизтопливо, или смазка?

[@TheElkinpalkin]

а смазка там почти никуда не попадает. он вынул оттуда старую смазку ,которая почти цвет не поменяла. она даже в смазывании не участвовала

[@КириллЗубков-ж3ю]

@@TheElkinpalkin Он мыл солярой места под подшипники. И все это добро ручьем польется на колодки...

[@jwdean9163]

My first thought also.

[@robertbould2638]

At first glance i thought the thumbnail was a raw rack of ribs.

[@Ernestoboy83]

I bet the skin of the hands is pretty greatful for this treatment.

[@azzante34]

...and after all that work, in comes a JDAM.

[@이름111-m3v]

더러운물이랑 폐유 그냥 길거리에 버려버릴것같은데...

[@benmiller5125]

Why do they insist on doing EVERYTHING on the ground. I get it's a poor area, but man tables are cheap. Also, way too much grease in those bearings and ??? preload applied.

[@MrRoque-pg3yr]

All by hand no machine tools. That’s a tough job.

[@murillogumiero]

The excess of lub is way worse than the lack of it.

[@mechanicmanish9593]

वीडियो अच्छा बनाया लेकिन इसमें बहुत कमी है वीडियो में कौन पर बेरिंग बैठाने के बाद दो पाठ और लगते हैं जिसको आप ने दिखाया ही नहीं

[@levharagezyan4596]

Я когда превью увидел сначало подумал что это рёбрышки.

[@aqimjulayhi8798]

The thumbnail looked like a skirt steak with nice marbling. Damn I’m hungry.

[@sptomcat866]

輪軸保養，現場都是黃土地灰塵沙粒，能做的好嗎??

[@sebastiandychto6080]

Nie mogę tego oglądać jak w tym piachu to wszystko robią!!!! Ale smaru nie żałował XD

[@Candle_Melting]

어우,, 수송부에서 두돈반 정비한 거 생각나네..;;

[@nuclearimbecile7674]

TATA MOTORS! Remember the Tata Nano? The car that could barely reach 100kph?

[@asmotormechanic2040]

Aapki yah 50000 km bhi chalne layak nahin hai aap ho na isko acche tarike se Sukha fitting karna tha taki pata lag sake ab hamari hub dhili hai ya tight hai

[@kyunghyunbae2208]

알수없는 알고리즘으로 들어왔는데.... 운전병 PTSD 씨게 오노 5톤차 허브 구리스 작업 진짜 개빡셋다 아직도 작업순서가 기억나ㅜㅠ

[@yunseok-01]

야외공업소지만 깨끗한 구리스 들어가는거보니 기분 좋네요 :)

[@skillstruckrepairer3880]

Good work, a little dirty, but honest work.

[@MayorMcheese12]

I dont think they have enough grease on there

[@skwol5184]

How much grease you want? Yes!

[@SandeepKumar-nw7oh]

Welding ka Mal kyon nahin bhara andar uske bad tool lagta hai kharab per aise hab Chadha Di