I Expertly Repair Broken Fiat Tractor Wheel Axle Most Amazing Technique // Must Watch This Video #lexpertlyrepairbrokentractoraxle #Most amazing technique #pkdiscoveringtechnology #fiattractorwheelaxle
Пікірлер: 202
@akaretnikov3 ай бұрын
Зачетный выключатель у станка! Видать ктото словил уже в лобешник ключ из патрона😂
@the_hate_inside10852 ай бұрын
Yeah, neat repair. But if you didn't overload every vehicle like madmen, in the first place, you wouldn't have to repair it at all...
@metalmickyАй бұрын
No mechanical sympathy……
@AGodHimself14 күн бұрын
In your defense, they break parts we don't break here in the US. So...... I agree with the both of you. (20 years auto technician)
@mercedesvan-doors342 ай бұрын
Some real engineering skill in this one, machine is clean and tools well kept. One piece of advice I would give is DON'T earth the weld through the lathe but directly on to the part, the arc will travel through bearings and eventually cause damage and failure. Good work.
@samotiag2 ай бұрын
Ребята за сотками на этом станке не гоняются, раз на нем варят и массой на деталь не заморачиваюnся.
@brandbmw6642Ай бұрын
мда. хоть бы направляющие прикрыли от сварки)
@alishabani4801Ай бұрын
درودبرشما خیلی هم ممنون از این کلیپ زیبا ❤ وبا درود به این داداش که استاد کار ماهری هستش کارش درسته دستش درد نکنه ایوالله دارید ۱۰۰۰تا ❤❤❤❤ انشاءالله همیشه موفق پیروز باشید در پناه خداوند ❤👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍🙏🙏🙏🙏🙏🙏🙏
@honkie2473 ай бұрын
The tractor sheared off a 2 inch forged steel shaft, and this repair is going to hold? More clickbait.
@alamanamoose2 ай бұрын
I had to go find my TI-83 calculator and did the math for you. This repair will hold just fine.
@honkie2472 ай бұрын
@@alamanamoose More clickbait.
@lrac77512 ай бұрын
The tractor will make it home, and that coincidentally, is where the warranty expires
@Robett-r4l2 ай бұрын
So apparently you're not smart enough to know that there are different hardness of Steel and for all you know which you don't know that center pin could be harder than the original Steel. But we wouldn't expect you to understand that because you're lost in la-la land and think you're smarter than what you actually are
@honkie2472 ай бұрын
@@Robett-r4l 46 years in a machine shop. You're correct, I have no idea. Even if the center pin is of a harder steel, the parent metal that is remaining has been reduced by approximately 50% by boring a hole and threading the hole for the center pin. So now you have the same load applied to the hub, but now there is only 50% of the parent metal left to take the stress. Now it will break twice as fast under the same load. Also, threading something in a situation like this causes stress risers, which will be the origination of stress cracks and failure in the parent metal. These types of posts are just clickbait to get views. Have you ever noticed that you NEVER see the repaired part put in service??
@rizvan32942 ай бұрын
Прочность -50℅
@Use_2024Ай бұрын
-80 кажется
@binhyen94632 ай бұрын
Bạn rất giỏi , tặng bạn 1 like. Lời chào từ Hà Nội, Việt Nam ❤
@renetannos2 ай бұрын
por sentido común la pieza volverá a fracturarse exactamente donde termina el perno que metiste. ese espacio queda completamente debil.
@alexsamu978728 күн бұрын
This repair will hold for 1 month maybe.
@Bretware9043 ай бұрын
Fake clickbait photos......blocked!
@grafluckner332 ай бұрын
Das , Sind Handwerker der Absoluten Spitzenklasse . ! - IMMER , WILLKOMMEN !!! Toller Beitrag !!!
@dianrangkuti9633Ай бұрын
Lll
@armandofernandezrobledo61202 ай бұрын
Las chispas con la bancada sin protección, no está nada bien
@محمدمسعود-ل9زАй бұрын
شاهدت هذا المقطع اكثر من مرة بسبب روعة و جمال العمل ؛ و لك مني كل تقدير و احترام احتسب عملك عند الله فتدخل الجنة دون سابقة عذاب وللمصور و المخرج كل التحية والتقدير
@annaskorek65672 ай бұрын
Wykonanie b.dobre!Byłem tokarzem 19 lat więc wiem jak wykonać.takie przypadki.
@davidgreenwood524122 күн бұрын
The usual health and safety gear on I see
@mrclassic22843 ай бұрын
Welding on the lathe is welding thru bearing surfaces
@RayMillTN12 ай бұрын
its ok, they are using the bearings rated for 200A
@DavoShed2 ай бұрын
Maybe he had the earth clamp on the tail stock 🤠 Perhaps he didn’t really drop the part on the bed when undoing the chuck. Maybe he didn’t really grind the face flat while the part was in a lathe! Perhaps he didn’t use the same threading tool for everything. There were definitely no stress fractures in that piece of previously sheared off bar used to effect the repair. I think his Expert status is intact. Personally I don’t know how anyone can weld in sandals
@bjoe74fmАй бұрын
instrument makers there not,, welding on a lathe spindle ,, how to break cardinal rules of maintaining machinery integrity lol
@flixemerson9582Ай бұрын
Dilapidated and dusty environment...nearly barefoot workers and fluttering clothes (easy pickup of kinematics), dirty machine and no protection of exposed sensitive parts. Kids out of school and forced to work, against the most basic norms...what future will this country have, ruled by those who keep the people poor and ignorant, just to ensure long life for political leaders?
@SergeyKingFox19 күн бұрын
Красиво.... но бессмысленно!!
@dalgleish120ify2 ай бұрын
Will never hold… shotty welding, no pre heat….
@pohakumana428828 күн бұрын
OEM Parts, just because it's shinny doesn't mean it new. I wouldn't put any weight on it.
@Exnay7772 ай бұрын
Go to the previous video...they show the shop that forges complete units...welding is not the way to go...will be broken again, and soon, the way these guys operate their equipment! And, they are weld-happy, problem is there's seldom the proper weld prep and too few passes. Here, he machines most of his weld off the part! But, I suppose that here it's a given the part will not last long, as you get what you pay for...
@artszabo1015Ай бұрын
Back in the old days us drag racers would narrow our rear ends and this is the EXACT method we used to shorten out axles. They held up to 2000 horse power and giant slicks without breaking. You have no clue what you are talking about other than your negative imagination. Art from Ohio
@piratelute8934Ай бұрын
LMAO the pseduo science of just tapping it level. What the actual fuck notice the time skip? This is literally impossible
@daveticehurst41912 ай бұрын
One turning tool does everything including threading !!!! Bet the thtreads are not to standard. Lathe slideways not covered up whilst welding, all the spatter going onto the slides. Looked a reasonable job in the end, wonder how long it will last. ?
@simonwelburn8799Ай бұрын
The skill of this fellow is incredible. Do you know how hard it is to make an interference fit between a metal shaft and hole? This worker does it so matter-of-fact and gets it right first time! Unbelievable!
@glotonoska3742Ай бұрын
Та біс із тою роботою, хтось знає навіщо у нього за спиною на стіні висять порвані ремені
@shuancook90052 ай бұрын
Nice safety shoes 👞 again 😀😀😀😀👞
@JR-nj8le17 күн бұрын
They already have advanced machinery in India??? 😡 BREXTIT NAU!
@hilmidukkel21852 ай бұрын
Usta çok özensiz kara düzen çalışıyor.Kaba talaş kaleminin açısı yanlış .yüksekliği yanlış.Kalemin ucu parçanın merkezinden yüksek.diş kaleminin açısı fazla ve fazla derin açıldığı için dişler döndü .Parçalar sıkı girmesi gerekirken çok boşluklu vidalandı içerideki vidanın mukavemete faydası yok.Ben bu tornacıya iş yaptırmazdım.
@ФигВам-д2р2 ай бұрын
Если цельный металл сдох, что уж говорить про эту порнографию
@jurybur_bobkov2 ай бұрын
а почему он полную не выточит, сможет же. видно токарь хороший. может дорогой металл?
@CharlesTryon-f9z2 ай бұрын
Gotta do what you gotta do I guess that was a 2”shaft that broke this might hold for a bit but will brake again like the other comet everything is overloaded there. But it’s not bad for what he has to work with.
@carlosgallo10792 ай бұрын
Comparado con la piezas q venden hoy en día, prefiero esta 👆
@georgewalton-b5s3 ай бұрын
a drop of oil helps
@Joefred772 ай бұрын
He probably doesn’t have any, fk it bone dry it is,😅
@76629online2 ай бұрын
I feel sorry for his old lady...I bet its chaff city for her! LMFAO!
@ЮрийКолесник-р7р3 ай бұрын
Я думаю еслеб делать горячую посадку ещоб билоб лутше делать несколько десяттк в плюсе е насажевмемую часть нагревать при нагреве отверстие увеличевается ну єто лутше пресом насаживать ответную часть и после остивания обварить и проточить в нужний розмер єто мое мнение 😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊
@jurybur_bobkov2 ай бұрын
я вообще сомневаюсь что такая тонкая стеночка что-то удержит. а если водила буксовать начнёт на асфальте? не провернёт ли эту чудо-ступицу? :)
@teobaldocarrenocaceres58122 ай бұрын
Un trabajo perfecto , felicitaciones !!👍👍👍
@desmo1fullАй бұрын
qualsiasi riparatore in Europa sa che questo non è affatto un buon lavoro,ma queste persone fanno il massimo con i mezzi a loro disposizione,li possiamo apprezzare solo per questo
@walter97243 ай бұрын
Long sleeves while using a lathe is bloody dangerous.
@beltranmiguelw2 ай бұрын
This people they don't know nothing about safety , they don't wear shoes, gloves, safety lenses noting they're focused in make money only
@trailblazer10472 ай бұрын
Safety seems not an issue over there,might have been that way for modern world in the beginning 1800's
@vintagerecordambassadeur409821 күн бұрын
They’re real men. They laugh at danger
@izharansari7498Ай бұрын
जुगाड़ू काम करते हो नया डाल कर छुट्टी करो
@pkfan511220 күн бұрын
Why mechanic doesn’t write down the number
@hisyamhisyam75632 ай бұрын
terbaik👍😊
@marcosavila8215Ай бұрын
these guy deserve every single cent they do with their content, i love it, amazing workers
@Cicade-dn4kb6 күн бұрын
Бедные люди... Они думают что если выглядит как не сломанная, то и пойдёт! Были бы у них технические знания, они б не занимались этой бессмысленной псевдоработой.
@Андрей-с8н9с2 ай бұрын
трактор на продажу tractor for sale
@pohakumana428828 күн бұрын
When your time is worth nothing and you can't afford parts, AMAZON does deliver in Pakiland don't they? All they Customer Service is there.
@alexeis610612 күн бұрын
Все это здорово, но если они сломали ту ступицу, то сломают и эту.
@elmu92616 күн бұрын
😊❤في الله مغاربة
@BanothJhoshap2 ай бұрын
👍👍👍👍👍👍👍
@trailblazer10472 ай бұрын
Id say that would last,good job.Those vehicles take a beating.And they are doing this for the camera,wonder if they are doing things a certain way to save time.
@brunodalessio46222 сағат бұрын
Wizard of the lathe!
@mahmoudbencheikh30312 ай бұрын
chapeau bas
@ParmjitsinghKhurmiАй бұрын
Good work by ❤❤❤
@EdVB32402 ай бұрын
son unos verdaderos maestros. felicitaciones !! 👏👏👍👍
@76629online2 ай бұрын
Eff it, that flange didn't need to be that thick anyway. lol. I reckon it'll probably last until they make the next video anyway.
@vladimirberac6666Ай бұрын
Založiť a potom uvidíš
@masudjang8992Ай бұрын
Good job
@vladimirberac6666Ай бұрын
Emulzia netreba načoo
@hansjung76182 ай бұрын
Das ist klar, wenn man es nicht probiert weiß man es nicht. Sandalen bei der Arbeit geht hierzulande gar nicht aber wenn man vieles auf die Füße kriegt muss man eben Sicherheitsschuhe tragen, das lässt man auch mal das Härten weg, Hauptsache es funktioniert nachher😊
@Reinaldo.Gongora2 ай бұрын
Espero que no le digan al cliente que la hicieron nueva fue reparada y creo que los indu son honestos
@barsyurtseven24233 ай бұрын
Mükemmel işçilik..
@anhtuanle466428 күн бұрын
pakistan quá giỏi
@arabiatit2arabiat14 күн бұрын
ابدااااااااااااااااااااااااااااااااااااااااااااااااااااااااااع والله اروع من شغل الماكينه الالمانيه ... ابداع تسلم ايدك
@orzubektoxtayev9562Ай бұрын
Бумайди
@petermoto4092 ай бұрын
Nothing expert or amazing about this hack-filled video.
@franklangone712Ай бұрын
No oil for cutting?
@GaryTruesdale19 күн бұрын
yup
@yayasumarya78422 ай бұрын
😂😂😂😂😂
@videosjoseruben2 ай бұрын
How long did the repair take? Question from Mexico City?
@Justone37229 күн бұрын
👍👍👍👍👍👍👍
@umitsakar6563Ай бұрын
❤🇹🇷🇹🇷🇹🇷👍👍👍👍👍👍👍harikasın usdam masallah
@ferroalloys59419 күн бұрын
Still not raining in any of these videos, remarkable! ):-)
@Skills-f4fАй бұрын
❤❤❤❤
@aussi321216 күн бұрын
he not only can run that lathe , but he has a great idea to repair that axle, using that threaded shank
@agusmm5970Ай бұрын
😯
@ismaelrojas40852 ай бұрын
Exelente trabajo !! 👏👏👏
@JohnDoe-ft2nh2 ай бұрын
These people are sooo good. Thank you for the video.
@tuhoa2373Ай бұрын
Tho tiên hay và gioi qua ďong dô long iêu
@imaginary25405 күн бұрын
amazing 👍
@KleinKonig-jd4mzАй бұрын
toll
@dorkuchotanihu95892 ай бұрын
Let's hope this steal shaft works, Anyway Good Job😂😂😂
@Use_2024Ай бұрын
Гарантия до ворот
@ЛеонидБрынских-у1с2 ай бұрын
И не прикапаешся, как заводская запчасть.
@wagner9161Ай бұрын
Assisti até o fim sem perder nenhuma parte.... muito bom o seu trabalho. Parabéns do Brasil..
@ktmtragic13972 ай бұрын
The drive handle is on the other side of the chuck !🤨
@markchodroff2503 ай бұрын
Something not done in many countries, but it looks like it would last if not it will be repaired again!
@TheUltimate65Ай бұрын
This repair wil work in all time in the future...👍👍👍👍
@Fulvioaci20 күн бұрын
bravi
@georgegonzalez24762 ай бұрын
It's likely to last from 6 minutes to an hour.
@tamacoronado27782 ай бұрын
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@barskaplan5589Ай бұрын
Eli e sağlık usta güzel işçilik
@edgardoprincipe2617Ай бұрын
asi se trabaja felicitaciones desde Argentina
@vanuongcao9272 ай бұрын
Ở đất nước nào vậy?
@活生-j3sАй бұрын
这种拼接法,强度明显不够 正确的做法是两边切斜口满焊
@kamillwojtowiczz33242 ай бұрын
Cast iron replaced with this GG
@miltonoooo2 ай бұрын
✅️👏🏼👏🏼👏🏼👏🏼excelente trabalho irmão!!!
@ChâuDuong-p3r2 ай бұрын
lại gãy tiếp tục .
@buktatoni3 ай бұрын
Super! Gratula...
@czirakiattila43983 ай бұрын
Azért ez több sebből is vérzik.😅 Ez a tengely a véglehajtásban van. Ha megfigyeled kompletten kiszedték a lehajtást féktengelytokkal kerekestől, talán féket javítanak. Erre a versenyzőnk elő húzza a kerékagy egyik részét a váltó difi részéből🤣😂 ahol a féltengely lenne amit látni is jobbra rajta a szalagfékkel.😂 Ez így mese habbal.🤣🤮🤠👌👎 Persze a rávaló fogaskereket nem látni de tettek oda pár hézagoló alátétet.
@buktatoniАй бұрын
@@czirakiattila4398 Az akaratot értékeltem és azt,hogy nem dobnak ki mindent ,közben pedig papolnak az ökolábnyomról. Egyébként valóban merész megoldás ami csak a gyakorlatban dől el,hogy mit faragtak?