Turn a $12 Box in 10 Minutes - The EDC Box

Turn a twelve dollar box in ten minutes. Via some simple small batch production run techniques on a lathe it's a simple project anybody can be successful at. Plus it's a great way to make a lot of gifts out of scrap wood.
This is an hour of tips and techniques. Good for beginners and experts wanting to learn or refine skills.
Link to the "4 Cuts" video mentioned: • Four Cuts - A Wood Tur...
----------------------------------------------------------
This channel is based on the value for value proposition. We depend upon patrons like you to fund our channel if you receive value from it. The time away from 'real work' that is our biggest expense. So if you feel these videos and series are of value to you and others please consider shopping and patronizing these sites:
- wortheffort.com
- squareup.com/m... (also for Donations)
- paypal.me/wort... for PayPal donations
- / wortheffort_ww
- / wortheffort_sg
- / wortheffort
Non-"Affiliate" Amazon list of recommended stuff - www.amazon.com...

[@joosts6535]

I really enjoyed watching this for over an hour at 3 o'clock at night. I don't even own a lathe.

[@thatguy5362]

Man I tell you what I got a lathe and it’s worth every penny and I don’t even do anything but make baseball bats and balls for the kids and some canes because I just got started but if you get the money to start the 3 foot lathe at harber freight is not bad for the price and for getting started.

[@codyayers2870]

Same dude

[@bethtorres5361]

Cocaine is a hellova drug

[@uncIeben]

Same

[@toonybrain]

😆

[@davidmsmith268]

I wanted to share something that some may see as obvious. Last night I was finishing up a small oak cylinder box like these and once I had it shaped and pulled off the lathe I couldn't pull the top off! I tried the rubber grabber sheets like you'd use to get a jar open with no luck. After a few minutes of thinking, I realized the wood had been sitting outside in the cold for a long time and I heated it while turning it. SO, Dropped it into the freezer for about an hour, pulled it out and the top popped right off. I hand sanded it down a bit to make sure it didn't happen again.

[@christophermckinney984]

As my dad would always say, that’s using your head for something other than a hat rack!

[@niklar55]

Quicker, if you have some, just spray it with pipe freeze.

[@mrbrianbray]

As a teacher, I respect you as a teacher. I stopped part way through to share this because this is what good teaching looks like.

[@KMFWR]

Me too! I agree fully!

[@studiohost]

excellent teacher x 100!!!

[@jamessinclar6118]

I was surprised it was an hour long. However, you broke it down step by step. Which is good for a for the true beginner like myself. Very informative and appreciated. This hour of watching will help me fine tune mine, hopefully, to 10 minutes. F the haters. Thank you!

[@wortheffort]

Ya, I talks too much.

[@jamessinclar6118]

@@wortheffort , not at all.

[@gfishin1332]

Shawn - I'm a 70 year old beginning turner (focussing mainly on fishing lures). Of all the videos on KZbin that I have watched, yours have been the most useful - and entertaining. I also really appreciate the practical and useful marketing ideas.

[@wortheffort]

Thanks

[@billy19461]

I am 73 and have been turning about 2 1/2 years.

[@povanator]

I'm fairly seasoned but mostly self-taught via these types of videos and I must say you are a hell of a teacher. I appreciate the safety notes and the "I shouldn't, buts..." thanks for posting!

[@twobluestripes]

This is a phenomenal demo. I’ve had one semester of woodturning at my woodworking program, bought a used jet mini like we used in class, and was hoping to get going on turning at home for exactly the reasons you said: easy to complete to a finished object fairly quickly, to make small gifts and saleable objects. I loved the explanation about the types of cuts as well and am going to be checking out more videos!

[@desironna]

The way you explain everything, amazed me ! It will leave no question in the end of tutorials..Amazing !

[@drobb4207]

Shawn is sincere and really, really wants to help us all. A rare quality in this day and age! Thanks Shawn! Don R

[@wortheffort]

Thanks

[@nemoemanon6679]

If he really, really wanted to help, he’d tell us the dimensions of the blank, diameters of the bits, drilling depths, etc. He’d share his story board.

[@wortheffort]

Nemo Emanon I did. Gave you a long closeup for you to pause on.

[@gmr3156]

I dont know. Im not sure if you really want to help us. I mean the only way to prove that would be to come to each of you subscribers homes and recreate that 1 scene from the movie Ghost. EDIT: But on a lathe obviously.

[@PaavoLammikko]

@@nemoemanon6679 Are you unable to figure out some stuff yourself? Do you need to have EVERY detail served before you can do anything? Make your own damn storyboard and be proud of it!

[@mmgross144]

You are an excellent teacher. Thank you for taking the time to share.

[@wortheffort]

Thanks

[@scottmorse1798]

humbug! they can make their own. im gona keep wartchin though, best teacher since jr high school and im 62.

[@jasonclinton3367]

When you pulled the one apart to show the internals, I couldn't figure out how you would get that one to stay together. You got me. Amazing work. Gonna give this a try soon.

[@Lostfriar1]

I've been wood working for a long time, turning wood on a lathe for a few years and I really appreciate your videos. Great content, supper presentation...!

[@jdscott20101]

Your videos are long but thats only because you cant fit so much amazing information and detail into 5 minutes. very impressed with your knowledge and willingness to share such in depth knowledge. please keep making great videos so we can all learn these great tips to be better. awesome video angles. no BS with begging for likes and what not. just great raw woodworking. love it. very glad i found your channel

[@LSatch]

Thanks Shawn for another great tutorial. I’m a better turner because of you. I know it’s a pain to produce and edit these but they really are helpful. “Worth the effort” for me to watch.

[@wortheffort]

Thanks

[@NMranchhand]

This is instruction equal to the best lectures given at the finest and oldest woodworking clubs in America. Literally, literally tied for the best of any, ANY, instructional video on KZbin. Special mention: the discussion of the ratio of time, money, and effort to the expected use and value of the product; a life lesson.

[@wortheffort]

Thanks

[@chrisdenison6550]

Just found you - what a breath of fresh air cheers Chris “The Aussie living in the Netherlands “🇦🇺🏁

[@jerryeaton2117]

J Vista is a little bit more aa ww iteal than wq Ed w2. D.d.jhmjjjj

[@LynnLaceyLLWW]

One of the best turning videos I've seen in a long time. Thanks

[@arukahwoodworking5487]

Hey, Shawn! I just wanted to say THANK YOU for all the videos you post. You're incredibly encouraging and educational, and I have been getting more into the craft because of you. Just made my first "EDC" box yesterday and it was exhilarating! Wouldn't have been able to do it without you!

[@wortheffort]

Thanks

[@elainefeather9465]

Thank you for another great tutorial .Not only “wortheffort “ watching ,but very much worthwhile ! I’m not only learning how to make some very nice beginner items , but , most importantly, learning how to make them safely .

[@treeorwh2]

I love you man. These videos are a treasure to me, just watching this and realizing how to focus on batching very valuable.

[@ph0sgene967]

I literally have never done woodworking outside of shop class and yet I'm enjoying this video. It was recommended to me. You're a great teacher!

[@wortheffort]

Thanks

[@benjamindelgado3488]

Omg I was watching this and got sucked in I didn’t realize it was an hour long till I finished the video amazing work will definitely try to make

[@wortheffort]

Thanks

[@Gix3D]

An hour worth watching.

[@jjcuvs9218]

Ha ha I just noticed it was 1 hour long. One hour well spend. Thanks for all the great tips. I just subscribed!!!

[@OregonOldTimerWOODTURNING]

I watched 4 Cuts yesterday and noticed that I'd watched and Liked it some time ago. That led me to this one. I see that I've watched and Liked this one before, too. Now that I have a year and a half of experience, I get a lot more out of your videos than I did the first time around.

[@loucinci3922]

Good lecture. Well presented. I was able visualize with the cross section prop. Nice touch!

[@wortheffort]

Thanks

[@74KU]

First time I have seen someone teach "peck drilling" in wood, a common method when machining metals, it doesn't seem to show up much in the wood community but certainly is worth the time to do. For what it is worth you will (should) end up with a hole closer to dimension, better surface finish and like you say. Less heat. Love the job.

[@wilcoxtube]

Really enjoy your teaching style. Even though this was an hour, I was interested from start to finish, and I picked up all sorts of tips. Looking forward to making some of these. Thank you for what you do!

[@davidgee1585]

Just bought second hand lathe, last used one at school almost 50 years ago. Your instructions on how to use this are excellent. Looking forward to having a go at these, it also came with a pen mandrill so will give that a go too, made a few bowls and lamps and a salt and pepper set before, but was never taught how to grind to sharpen the chisels. Thanks for posting all this, what a great thing You tube is too!

[@rodw]

I really enjoyed this video. Thanks for sharing your thoughts, skill, and videos, Rodney

[@wortheffort]

Thanks

[@timothyhamilton9961]

I just got my first cheap mini lathe and love practising the basics. i have watched thousands of videos and this is the BEST. Thank you

[@MikePeaceWoodturning]

Always interesting to learn production tricks. Good job, Shawn.

[@wortheffort]

Thanks

[@FRECSF1]

I have to say, I really enjoy your presentation and teaching skills. Wood working has always been intimidating to me. I have a brother and brother in law who does this as a hobby and I think it is great. After watching a few of your video's they have motivated me to venture out a little and start looking at doing some wood work.

[@wortheffort]

Do it. The more trees you use the more they'll plant and the more carbon will be sequestered from the air. Do it for the planet.

[@leonarddavis3684]

I do not have a lathe, but this makes me want one even more, thank you.

[@chuckorsburn4452]

Me to

[@rickschuman2926]

I really appreciate this. I see so many people get into an art or craft and even music who get some kind of kucky and think "l've got this". In my going along, l switched from using an electric lathe to using a spring pole lathe. I was making pattern work for foundry with the electric but the work went away and l moved my shop soon after. I never set that lathe up again but l did build a pole lathe. That was 17 Winters ago now. For the last 13 years l have been setting up and demonstrating at festivals and reenactment events. That first 4 years l spent at home transferring and developing turning skills. After 4 years, l pretty much had the techniques of turning and other green woodworking tools and methods well in hand so l went on tour. Taking the time to develop a deeper and broader range of skills is never a mistake. It is the way to move from hobby to something more fulfilling and,in some circumstances and places, there might be some income but you're gonna have to hustle.

[@markbeiser]

A bunch of not identical spindle turnings? Sounds like it is perfectly suited to my skill level! :D

[@wortheffort]

Ya, make randomness an asset. Production mentality no. 1.

[@UsernameWasLost]

@@wortheffort it's not a mistake, it's a feature!

[@fionam3554]

I use that attitude in golf. Aim at the sand trap! It is now out of play. The ball will end up anywhere in the cosmos EXCEPT that trap.

[@markbeiser]

@@wortheffort When I failed at making reasonably identical spindles for the legs of a small table, I just threw a half ass finish on it and called it "rustic". ;)

[@paulw7770]

Well done! Not a lot of useless chatter, just good information on how to be a productive human. Very enjoyable, thanks!

[@wortheffort]

Thanks

[@thomasarussellsr]

"The family stoner", ROTFLMBO! Great little project.

[@wortheffort]

Every family has one.

[@Mercenary_32]

@@wortheffort LOL 🤣

[@glen3257]

lmao love the skill and keeping it real.

[@juneebennett22]

@@wortheffort Or two or three if you live in Washington state 🤣

[@garyfairbrother5532]

This came up after a Stumpy Nubs video and I was hooked right away by your personality and sincerity so I kept watching and I too don’t have a lathe…don’t even want one. That’s charisma in spades.

[@knottie_gurldeannamorris1136]

Shawn, I really enjoyed this video! Have you thought of making a plastic version, or CNC version, of your template and selling it on your website?

[@wortheffort]

Thanks, you can make one in less than a minute so no need to buy one.

[@garycovington6110]

Yes to this! I watched your video twice learned so much. I then turned one out of scrap oak. Thanks for the video and your knowledge.

[@A50S2D]

I call mine "needle cases" and sell to women who do sewing. I also put a small magnet in the lid so the needles don't fall out when they open it. Then they don't have to take their shoes off to find the lost needles.......

[@wortheffort]

Ya, that's what these are traditionally called.

[@slowfootlabeef704]

Excellent lathe technique and excellent teaching technique

[@CerebralOrigami]

Put the super glue on the inside of the cap so it wont show.

[@wortheffort]

good idea

[@JLP75766]

One of the best instructional video I have ever seen on KZbin.

[@wortheffort]

Thanks

[@alabamahebrew]

Poor Skip, always being left out... lol

[@Sigurd_Alemaker]

Natural born teacher! Loved every minute of this, cant wait to try it out!

[@tedpuckett2779]

“Stan the family stoner”....lol

[@wortheffort]

Every family has one, or that just might be an Austin thing.

[@DragonGateDesign]

I thought it was skip

[@tylervagrancy3842]

@@wortheffort Enable? Is there something wrong with taking advantage of the natural health benefits of cannabis? BTW, a 1 hour video for a 10 minute simple spindle project? Nahh..

[@wortheffort]

@@tylervagrancy3842 Only for people without a sense of humor.

[@gertmassaer2360]

@@tylervagrancy3842 did you actually took the time to watch the whole video ? If you did, you would know theres much more information and tips in the video besides the turning of one spindle project. It's also about batching stuff out, following logic steps to make as much as possible in a short amount of time, tips on how to sell, how to size the tenon... etc. Personaly i think we should admire people who actually take the time and effort to make good quality and detailed content, these days youtube is more and more short video's without much detail becouse of one simple thing... money. Again thats my personal oppinion offcourse.

[@billpayne2713]

The way that you show this is great. It leaves no questions. Thank you for taking time to help a beginner.

[@tmhcanonshooter]

You are an excellent instructor! Best use of a skew that I have ever seen.

[@RalphSutter]

Thanks for a very informative video. After watching, I turned a few EDC boxes but was challenged to get a tight pop-tight fit for the top. I simplified the approach by first turning a cylinder. Next, I parted it and drilled a hole of known diameter in each section. Then, I turned a dowel the same diameter as the hole and glued it into the top, leaving about 1/4" protruding. That protrusion fit tightly into the base. Using this approach, I saved myself from the challenge of cutting a perfect tenon. To simplify even further, I could have purchased a ready made dowel the same size as the hole that I drilled.

[@aliabazaid4293]

You are sincere in your profession, You deserve all appreciation

[@dexhorton]

Thanks for the great teaching! Your explanation on moving the tailstock forward when using the Jacobs Chuck was just what I needed. I searched and searched for that information, and almost returned the chuck because it was so wobbly.

[@ragcell]

Who has time to watch an hour-long video? The problem with this video is that it is like popcorn: it is impossible to stop watching. This is one of the better videos I have ever seen, not that it something I will likely do in spare time (whatever that is…) nor do I still have a lathe on my wish list, this is so damn informative and fun to watch. Kudos Wortheffort for easy to follow and understand and reasoned information. This wisdom is easily applicable to other interests. Thank you.

[@wortheffort]

Thanks

[@bunyardfamily2264]

Hi Shawn. I work at a retail woodworking store and when I get customers that buy a lathe for the first time I always recommend your channel as a must watch for new turners. Keep up the good work!

[@wortheffort]

Bunyard Family thanks

[@billroberts3864]

A great teacher demonstrates good techniques on turning a pin box.

Dude, you're a freaking genius. I used to turn boxes but it was fitting the lid that was most time-consuming. And if I was lucky I could turn, not including finishing, 6 - 8 a day. It just wasn't profitable. Now I can be thanks to you.

[@wortheffort]

6-8 from blanks ain't bad.

@@wortheffort Thanks but there are few turners who understand production and how it relates to price point which may or may not result in sales (no offense guys). I'd love to get all artsy with my work, but it typically isn't worth the time. So like you, I only make what sells and I like to stick to simple designs that I can produce quickly and in large runs with common easy to get wood species. I never considered making these toothpick boxes until you showed me this simple method of hollowing. I'm a little embarrassed that I didn't think of this. Just sneak up on the correct tenon size then all's left is to finalize the proportions. Part it off, oil, and repeat. I've got a big show coming up in a few months and I needed some new products and I think at this price point they'll be perfect. Thanks again.

[@roytaylor5463]

Without a doubt, one of the best instructional videoes I have watched. The commentary was clear and concise and very informative as well as instructional. Many thanks for taking the time.

[@monopinion8799]

Tony you are not the only one. Luckily this video is a gem. Thank you so much fo the wonderful gift for the gift idea. Great introduction and demonstration. Your wonderful.

[@gatekeeper65]

you're beyond generous with the skills and tips you're offering here. These are skills that can take years to learn without this information. Thank you very much. Take care, and have a great day.

[@brianroyle2533]

Brilliant demonstration really enjoyed it and learnt a lot thank you

[@tedcarson2971]

Your videos are rapidly becoming addictive!!! I'm learning so much and having a great time doing it. Thank you.

[@Halscamp]

I finally got around to trying this. Super, Super happy with the outcome. I burnt 1 line at the bottom , 2 at the top and 1 where the top and bottom join together --- you would never know it separates.. Thanks WTE.

[@jameswarner6105]

Shawn, I thank you so much for not only showing us what you are doing but explaining how you are doing it an why you are doing it. I really appreciate the educational quality of your videos. Now out to the workshop to try this. :)

[@gsp911]

I am at the beginning of woodturning and learned quite a lot here. Thanks for sharing. 👍

[@dr.sawdust4278]

I'm watching woodwork video's for a long time now. And suddenly you pop up. You are a real good teacher! I love your video's! I Will watch them all

[@wortheffort]

Thanks

[@seemorevid1]

Your method of finishing the ends and parting off was a very useful tip. I have had the tear out problem, so I will use this idea.

[@danmichaud580]

Great video. Enjoy it when you do a project and explain it from start to finish. It makes you feel like you are doing it for me.

[@wortheffort]

Thanks

[@susanp.collins7834]

Totally genius marketing technique! Gosh - you could use these little boxes for ANYTHING! I'm looking at them for herbs and spices...

[@FreeRangeCreative]

I'm new to turning and have been making a version of these for s few weeks now. Thanks for this!

[@HomesteadSoapCo]

The time and detail you go into is unlike any other turner on yt. I’ve been a fan for a long time and you taught me to turn. 2 lathes and many many projects later I would say you were my teacher. Thanks man. Really.

[@wortheffort]

HomesteadSoapCo thanks. Means a lot.

[@isaacderr2799]

What a cool video! I’ve noticed that the guys who really know what they are doing are never afraid to share their tips and expertise. Sharing the economy of these little boxes is a very kind thing to do. For all he knows, 3 new guys are gunna show up at the art market with armfuls of little boxes selling them for $10 a piece. BUT you can always tell an artist/craftsman who has spent years honing their craft from someone trying to make easy money; and the difference is worth it. Craftspeople will always have a place. Every song, video, book, or purchase is in our pockets for little, less, or money; but there are still live shows, live/movie theaters, literature readings, and art markets. I’m a musician/recording engineer and the lack of human interaction caused by Covid-19 (it’s critical to not overwhelm our healthcare infrastructure, don’t get me wrong) has totally wrecked the human interaction element that is so important to artists/craftspeople’s livelihoods. TLDR: Those who can do, teach. Thank you for giving all the time and effort (not to mention $$$) that goes into a good production quality video made by a true craftsman.

[@wortheffort]

Thanks

[@Christopher_Giustolisi]

I just made haf a dozend of these out of a piece of firewood. Definitely worth the effort.

[@dfu1685]

You are such a wonderful Teacher. Merry Christmas 🎄

[@rpmfoto]

Fabulous info. You are THE best teacher. At 100 K your rocket is just launching.

[@wortheffort]

Thanks. Just launching after nine years....

[@rpmfoto]

wortheffort you’ve been energizing like Goku for 9 years. Now the rocket has enough energy to launch.

[@trishkauffeldt8701]

OMG, I am totally nerding out over this video! I relented and decided to try the skew as you were instructing and FINALLY managed to make an actual item with it, instead of freaking out and quitting! LOL It has always scared me, but all of your tips and tricks were magic. Thank you so much!! I'm so excited right now!😁

[@andoidv8945]

Fantastic!! I learned so much from this tutorial, many thanks

[@wavetrader742]

As an amateur wood turner, I always enjoy your videos. Anyone doing "how-to" videos for any skill would do well to watch your teaching techniques because I haven't seen many people do them as well. All the best to you!

[@wortheffort]

Thanks

[@toonybrain]

That cross section was a great idea, a helpful visual. Thank you for this video. Here in Florida I found that boxwood is a wonderful wood, but it’s a slow-grower. None of the branches one prunes are large. These boxes are perfect.

[@wdnick]

The magnetic base for a cutoff length stop was worth the price of admission. Why have I never thought of this???? No more clamping a board to my fence assuming that I remember this next time. :)

[@wortheffort]

That came in the caliper set from Grizzly. I think it's called the presidents set because it's a group of set up gauges chosen by president of company and is likely their best value product.

[@danchannel9316]

This is fantastic. You are a great teacher. I'm new at the lathe but have taken a few classes. This was more helpful than any of my other classes. Thank you!

[@mrgolftennisviolin]

Made my first edc box tonight! It was my first time using my scroll chuck, and first time using jacobs chuck as well. Thanks for the awesome project idea!

[@hankvermote9353]

You are the best instructor online that I have ever seen. I plan on watching many more of your videos. Thank you!

[@dangood6949]

I rarely watch a one hour video but yours are definitely WORTH THE EFFORT !!

[@TheSilvereagle247]

Very good instructions. I like it. You seem like a great guy. Thank you!

[@shedmanx3640]

Absolutely amazing demonstration and teaching style. That hour felt like 10 minutes. I was captivated.

[@DacaTimberworks.]

Hey bro just wanted to let you know I watched a couple of your vids about 9 months ago when I first started turning and enjoyed them and found them very useful. I'm now revisiting them and find them so so much more useful now that I have a basic grasp of turning and some hands on experience. I'm probably going to rewatch your entire library now because you're such a good teacher and now I need to understand the why's how's when's and what's going on. Thanks for sharing your knowledge and experience it's much appreciated.

[@Chef_PC]

Every time you do a video like this, I jones for a lathe and a nice shop space. Love it.

[@wortheffort]

Getting a lathe is your first step into a rabbit hole of addiction. Be warned.

[@DanaOredson]

Thanks for walking us through this. I've been intimidated by lathe boxes in the past, but the way you teach it seems doable!

[@TheRealKirkHammett]

I like the way you think. Some things you do I might do differently, but I agree with your approach to almost everything.

[@billinfarmington5189]

I know it has been almost a year since you put this up and I have watched it several times. I finally got my buddies lidded box off the lathe after about a month and made my first little box out of maple. I copied out all the instructions step by step and all went really well. Success! Regards, Bill

[@MoFooKiN]

Me too! Man youve taught me so much more on the lathe than the other guys just by the way you go through things. I wish all the teachers ive had taught half as good as you. Keep it up! Im recommending you to all my wood working friends!

[@DavidFraserYHZ]

You have a gift for teaching. Thanks for sharing your skills.

[@billballeza377]

Simply no better instruction to be found. Thank you!

[@lenshandcraftedwoodsigns6033]

Thank you for showing this. They look like a simple enough item to make while honing my skills.

[@stuartwass6672]

Some great tips , stuff I hadn’t thought about, eureka moments 👍🏽👍🏽

[@MrAtfenn]

i cant thank you enough for taking the time to pass on your knowledge and experience to all of us novices of the craft. your long form style takes the time needed to fully teach a subject. rob cosman and you are the two men on youtube that i trust when i need to learn a new technique. again, thank you so much for really taking the time to help the rest of us novices out here

[@pnwguy221]

Thank you sir. You are doing a fantastic job in your shop and teaching new turners like myself the skills of wood turning. I am new to turning and have been watching some of your videos for tips and techniques to apply to my new hobby. You are a great teacher, keep it up.

[@briannahardey8796]

At first this seemed a bit long. Then I realized that it WAS long, but it is because you explain things so well. I learned a lot and am motivated to try making a box. Thanks

[@wortheffort]

Thanks

[@bartman59laj55]

You’re a good teacher, thanks from a beginner

[@AustereHare]

man i love this channel. totally want a lathe